scholarly journals Carbon dioxide adsorption and interaction with formation fluids of Jordanian unconventional reservoirs

Author(s):  
H. Samara ◽  
T. V. Ostrowski ◽  
F. Ayad Abdulkareem ◽  
E. Padmanabhan ◽  
P. Jaeger

AbstractShales are mostly unexploited energy resources. However, the extraction and production of their hydrocarbons require innovative methods. Applications involving carbon dioxide in shales could combine its potential use in oil recovery with its storage in view of its impact on global climate. The success of these approaches highly depends on various mechanisms taking place in the rock pores simultaneously. In this work, properties governing these mechanisms are presented at technically relevant conditions. The pendant and sessile drop methods are utilized to measure interfacial tension and wettability, respectively. The gravimetric method is used to quantify CO2 adsorption capacity of shale and gas adsorption kinetics is evaluated to determine diffusion coefficients. It is found that interfacial properties are strongly affected by the operating pressure. The oil-CO2 interfacial tension shows a decrease from approx. 21 mN/m at 0.1 MPa to around 3 mN/m at 20 MPa. A similar trend is observed in brine-CO2 systems. The diffusion coefficient is observed to slightly increase with pressure at supercritical conditions. Finally, the contact angle is found to be directly related to the gas adsorption at the rock surface: Up to 3.8 wt% of CO2 is adsorbed on the shale surface at 20 MPa and 60 °C where a maximum in contact angle is also found. To the best of the author’s knowledge, the affinity of calcite-rich surfaces toward CO2 adsorption is linked experimentally to the wetting behavior for the first time. The results are discussed in terms of CO2 storage scenarios occurring optimally at 20 MPa.

2021 ◽  
Author(s):  
Amir Hossein Saeedi Dehaghani ◽  
Seyed Masoud Ghalamizade Elyaderani

AbstractIn this study, we initially performed interfacial tension (IFT) tests to investigate the potential of using the Persian Gulf seawater (PGSW) as smart water with different concentrations of NaCl, KCl, MgCl2, CaCl2, and Na2SO4. Next, for each salt, at the concentration where IFT was minimum, we conducted contact angle, zeta potential, and micromodel flooding tests. The results showed that IFT is minimized if NaCl or KCl is removed from PGSW; thus, for solutions lacking NaCl and KCl, the IFT values were obtained at 26.29 and 26.56 mN/m, respectively. Conversely, in the case of divalent ions, minimum IFT occurred when the concentration of MgCl2, CaCl2, and Na2SO4 in PGSW increased. Specifically, a threefold rise in the concentration of Na2SO4 further reduced IFT as compared to optimal concentrations of MgCl2 or CaCl2. It should be mentioned that eliminating NaCl from PGSW resulted in the lowest IFT value compared to adding or removing other ions. Whereas the removal of NaCl caused the contact angle to decrease from 91.0° to 67.8° relative to PGSW and changed surface wettability to weakly water-wet, eliminating KCl did not considerably change the contact angle, such that it only led to a nine-degree reduction in this angle relative to PGSW and left wettability in the same neutral-wet condition. At optimal concentrations of MgCl2, CaCl2, and Na2SO4, only an increase in Na2SO4 concentration in PGSW could change wettability from neutral-wet to weakly water-wet. For solutions with optimal concentrations, the removal of NaCl or KCl caused the rock surface to have slightly higher negative charges, and increasing the concentration of divalent ions led to a small reduction in the negative charge of the surface. The results of micromodel flooding indicated that NaCl-free PGSW could raise oil recovery by 10.12% relative to PGSW. Furthermore, when the Na2SO4 concentration in PGSW was tripled, the oil recovery increased by 7.34% compared to PGSW. Accordingly, depending on the conditions, it is possible to use PGSW so as to enhance the efficiency of oil recovery by removing NaCl or by increasing the concentration of Na2SO4 three times.


2016 ◽  
Vol 864 ◽  
pp. 194-198 ◽  
Author(s):  
Mohd Shahrizan Moslan ◽  
Wan Rosli Wan Sulaiman ◽  
Abdul Razak Ismail ◽  
Mohd Zaidi Jaafar ◽  
Issham Ismail

Wettability alteration of rock by surfactant has been considered as feasible method for recovery of oil reservoirs by modifying the wettability of rock surface from oil-wet to water-wet condition. The impact of surfactant can be enhanced by adding nanoparticles. Cationic surfactant performed well in carbonate rock by forming ion pairs between cationic head and acidic component of the crude. Meanwhile, nanoparticles will form continuous wedge film between the liquid and solid surface. In this paper, Al2O3 and ZrO2 nanoparticles were used as enhanced oil recovery (EOR) agents. The impact of these two nanoparticles on contact angle and interfacial tension was studied. Besides that, adsorption Cetyltrimethylammonium Bromide (CTAB) surfactant on rock surface was also investigated. The results show a significant change in water-oil contact angle after application of surfactant and nanoparticles. Initial water-oil contact angle for 6 dolomites demonstrate oil-wet condition. Then, the dolomites were submerged in prepared solution for 48 hours. The result shows that, dolomites 2, 5 and 6 changes drastically to more water-wet condition with contact angle 56°, 40° and 47° respectively. For surfactant adsorption, the adsorption is very fast at the beginning. The adsorption rate after 5 minutes was 50 mg/g and after 60 minutes the adsorption rate was 310 mg/g. The adsorption rate slowed down after 60 minutes and after 180 minutes the adsorption rate was 315 mg/g in which the rate of adsorption achieve equilibrium. Nanoparticles retention test and Zeta potential shows that Al2O3 is more stable than ZrO2. The results for interfacial tension (IFT) also show a significant reduction. The IFT value reduces from 8.46 mN/m to 1.65 mN/m and 1.85 mN/m after the application of Al2O3 and ZrO2 nanofluids respectively


2021 ◽  
Author(s):  
Xu-Guang Song ◽  
Ming-Wei Zhao ◽  
Cai-Li Dai ◽  
Xin-Ke Wang ◽  
Wen-Jiao Lv

AbstractThe ultra-low permeability reservoir is regarded as an important energy source for oil and gas resource development and is attracting more and more attention. In this work, the active silica nanofluids were prepared by modified active silica nanoparticles and surfactant BSSB-12. The dispersion stability tests showed that the hydraulic radius of nanofluids was 58.59 nm and the zeta potential was − 48.39 mV. The active nanofluids can simultaneously regulate liquid–liquid interface and solid–liquid interface. The nanofluids can reduce the oil/water interfacial tension (IFT) from 23.5 to 6.7 mN/m, and the oil/water/solid contact angle was altered from 42° to 145°. The spontaneous imbibition tests showed that the oil recovery of 0.1 wt% active nanofluids was 20.5% and 8.5% higher than that of 3 wt% NaCl solution and 0.1 wt% BSSB-12 solution. Finally, the effects of nanofluids on dynamic contact angle, dynamic interfacial tension and moduli were studied from the adsorption behavior of nanofluids at solid–liquid and liquid–liquid interface. The oil detaching and transporting are completed by synergistic effect of wettability alteration and interfacial tension reduction. The findings of this study can help in better understanding of active nanofluids for EOR in ultra-low permeability reservoirs.


Author(s):  
Sergey Bublik ◽  
Sarina Bao ◽  
Merete Tangstad ◽  
Kristian Etienne Einarsrud

AbstractThe present study has investigated the influence of sulfur content in synthetic FeMn and SiMn from 0 to 1.00 wt pct on interfacial properties between these ferroalloys and slags. The effect of experimental parameters such as temperature and holding time was evaluated. Interfacial interaction between ferroalloys and slags was characterized by interfacial tension and apparent contact angle between metal and slag, measured based on the Young–Laplace equation and an inverse modelling approach developed in OpenFOAM. The results show that sulfur has a significant influence on both interfacial tension and apparent contact angle, decreasing both values and promoting the formation of a metal-slag mixture. Despite the fact that sulfur was added only to the ferroalloys, most of sulfur is distributed into slag after reactions with the metal phase. Increasing the maximum experimental temperature in the sessile drop furnace also resulted in a decrease of both interfacial properties, resulting in higher mass transfer rates and intensive reactions between metal and slag. The effect of holding time demonstrated that after reaching equilibrium in FeMn-slag and SiMn-slag systems (both with and without sulfur), interfacial tension and apparent contact angle remain constant.


2021 ◽  
Vol 303 ◽  
pp. 01001
Author(s):  
Yu Haiyang ◽  
Ji Wenjuan ◽  
Luo Cheng ◽  
Lu Junkai ◽  
Yan Fei ◽  
...  

In order to give full play to the role of imbibition of capillary force and enhance oil recovery of ultralow permeability sandstone reservoir after hydraulic fracturing, the mixed water fracture technology based on functional slick water is described and successfully applied to several wells in oilfield. The core of the technology is determination of influence factors of imbibition oil recovery, the development of new functional slick water system and optimization of volume fracturing parameters. The imbibition results show that it is significant effect of interfacial tension, wetting on imbibition oil recovery. The interfacial tension decreases by an order of magnitude, the imbibition oil recovery reduces by more than 10%. The imbibition oil recovery increases with the contact angle decreasing. The emulsifying ability has no obvious effect on imbibition oil recovery. The functional slick water system considering imbibition is developed based on the solution rheology and polymer chemistry. The system has introduced the active group and temperature resistant group into the polymer molecules. The molecular weight is controlled in 1.5 million. The viscosity is greater than 2mPa·s after shearing 2h under 170s-1 and 100℃. The interfacial tension could decrease to 10-2mN/m. The contact angle decreased from 58° to 22° and the core damage rate is less than 12%. The imbibition oil recovery could reach to 43%. The fracturing process includes slick water stage and linear gel stage. 10% 100 mesh ceramists and 8% temporary plugging agents are carried into the formation by functional slick water. 40-70 mesh ceramists are carried by linear gel. The liquid volume ratio is about 4:1 and the displacement is controlled at 10-12m3/min. The sand content and fracturing fluid volumes of single stage are 80m3 and 2500 m3 respectively. Compared with conventional fracturing, due to imbibition oil recovery, there is only 25% of the fracturing fluid flowback rate when the crude oil flew out. When the oil well is in normal production, about 50% of the fracturing fluid is not returned. It is useful to maintain the formation energy and slow down the production decline. The average cumulative production of vertical wells is greater than 2800t, and the effective period is more than 2 years. This technology overcoming the problem of high horizontal stress difference and lack of natural fracture has been successfully applied in Jidong Oilfield ultralow permeability reservoir. The successful application of this technology not only helps to promote the effective use of ultralow permeability reservoirs, but also helps to further clarify the role of imbibition recovery, energy storage and oil-water replacement mechanism.


Nanomaterials ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 1296 ◽  
Author(s):  
Reidun C. Aadland ◽  
Salem Akarri ◽  
Ellinor B. Heggset ◽  
Kristin Syverud ◽  
Ole Torsæter

Cellulose nanocrystals (CNCs) and 2,2,6,6-tetramethylpiperidine-1-oxyl (TEMPO)-oxidized cellulose nanofibrils (T-CNFs) were tested as enhanced oil recovery (EOR) agents through core floods and microfluidic experiments. Both particles were mixed with low salinity water (LSW). The core floods were grouped into three parts based on the research objectives. In Part 1, secondary core flood using CNCs was compared to regular water flooding at fixed conditions, by reusing the same core plug to maintain the same pore structure. CNCs produced 5.8% of original oil in place (OOIP) more oil than LSW. For Part 2, the effect of injection scheme, temperature, and rock wettability was investigated using CNCs. The same trend was observed for the secondary floods, with CNCs performing better than their parallel experiment using LSW. Furthermore, the particles seemed to perform better under mixed-wet conditions. Additional oil (2.9–15.7% of OOIP) was produced when CNCs were injected as a tertiary EOR agent, with more incremental oil produced at high temperature. In the final part, the effect of particle type was studied. T-CNFs produced significantly more oil compared to CNCs. However, the injection of T-CNF particles resulted in a steep increase in pressure, which never stabilized. Furthermore, a filter cake was observed at the core face after the experiment was completed. Microfluidic experiments showed that both T-CNF and CNC nanofluids led to a better sweep efficiency compared to low salinity water flooding. T-CNF particles showed the ability to enhance the oil recovery by breaking up events and reducing the trapping efficiency of the porous medium. A higher flow rate resulted in lower oil recovery factors and higher remaining oil connectivity. Contact angle and interfacial tension measurements were conducted to understand the oil recovery mechanisms. CNCs altered the interfacial tension the most, while T-CNFs had the largest effect on the contact angle. However, the changes were not significant enough for them to be considered primary EOR mechanisms.


1964 ◽  
Vol 4 (03) ◽  
pp. 231-239 ◽  
Author(s):  
A.S. Michaels ◽  
Arnold Stancell ◽  
M.C. Porter

MICHAELS, A.S., MASSACHUSETTS INSTITUTE OF TECHNOLOGY, CAMBRIDGE, MASS. MEMBER AIME STANCELL, ARNOLD, MASSACHUSETTS INSTITUTE OF TECHNOLOGY, CAMBRIDGE, MASS. PORTER, M.C., MASSACHUSETTS INSTITUTE OF TECHNOLOGY, CAMBRIDGE, MASS. Abstract Previous laboratory studies have demonstrated that the injection of small quantities of reverse wetting agents during water displacement can increase oil recovery from unconsolidated porous media. In the present investigation, an attempt has been made to determine more fully the effects of reverse wetting treatments and to clarify the mechanism by which increased oil recovery is effected Water-oil displacements were performed in beds of 140–200 mesh silica sand. Hexylamine slugs (injected after 0.25 pore volume of water through put), when adequate in size and concentration, were effective in promoting additional oil recovery. Their effectiveness increased with the quantity of amine injected. However, slugs of sufficient size and concentration to stimulate oil production at water flow rates of 34 ft/day did not do so at 4 ft/day.Visual studies in a glass grid micromodel have shown that the stimulation of oil production, via aqueous bexylamine, is a result of transient changes in the oil wettability of the pore walls. If the am in e slug is of sufficient size and concentration to induce significant changes in the adhesion-tension, large continuous oil masses will be formed. If the superficial water velocity is high enough to result in rapid desorption of the am in e, a favorable "wettability gradient" may be established across the masses; under such conditions, high oil mobility is observed, and increased oil recovery results. Introduction It is generally agreed that the efficiency of oil displacement by water in porous media is limited in part by capillary forces which cause the retention of isolated masses of oil - resulting in the so-called "irreducible minimum oil saturation". Recent estimates indicate that there are about 220 billion bbl of petroleum in United States reservoirs which are not economically recoverable with present techniques (such as water flooding). This amounts to almost five times the known recoverable reserves. It has been recognized for some time that a suitable alteration in the water-oil interfacial tension and/or the contact angle, as measured between the water-oil interface and the solid surface, should result in better displacement efficiency. Surface active agents can be used as interfacial tension depressants to accomplish this objective, but unfortunately, the additional oil recovery is seldom commensurate with the treatment cost.In contrast to interfacial tension depressants, the effect of contact angle alterations on water- oil displacements has received relatively little attention in the literature. It is known that the wettability affects the displacement process. Displacements in water-wet systems generally result in lower residual oil saturations than those in oil-wet systems. The effect of "transient" wettability alterations concurrent with the displacement process have been investigated by Wagner, Leach and coworkers, wherein it has been demonstrated that the establishment of water- wet conditions during water flooding of oil-wet, oil-saturated porous media is accompanied by significant increase in oil displacement efficiency. Michaels and Timmins studied the effects of transient contact angle alterations resulting from chromatographic transport of reverse wetting agents through unconsolidated sand. It was demonstrated that chromatographic transport of short-chain (C4 through C8) primary aliphatic amines can improve oil recovery and that the recovery increases with the quantity of amine injected (i.e., with either the amine concentration or the volume of the slug injected). Circumstantial evidence indicated that the increased displacement efficiency resulted primarily from transient changes in wettability of the porous medium.In the present investigation, additional information has been obtained on the effects of reverse wetting treatments and the mechanism by which increased oil recovery is accomplished. SPEJ P. 231^


2018 ◽  
Author(s):  
M. Elsharafi ◽  
K. Vidal ◽  
R. Thomas

Contact angle measurements are important to determine surface and interfacial tension between solids and fluids. A ‘water-wet’ condition on the rock face is necessary in order to extract oil. In this research, the objectives are to determine the wettability (water-wet or oil-wet), analyze how different brine concentrations will affect the wettability, and study the effect of the temperature on the dynamic contact angle measurements. This will be carried out by using the Cahn Dynamic Contact Angle. Analyzer DCA 315 to measure the contact angle between different fluids such as surfactant, alkaline, and mineral oil. This instrument is also used to measure the surface properties such as surface tension, contact angle, and interfacial tension of solid and liquid samples by using the Wilhelmy technique. The work used different surfactant and oil mixed with different alkaline concentrations. Varying alkaline concentrations from 20ml to 1ml were used, whilst keeping the surfactant concentration constant at 50ml.. It was observed that contact angle measurements and surface tension increase with increased alkaline concentrations. Therefore, we can deduce that they are directly proportional. We noticed that changing certain values on the software affected our results. It was found that after calculating the density and inputting it into the CAHN software, more accurate readings for the surface tension were obtained. We anticipate that the surfactant and alkaline can change the surface tension of the solid surface. In our research, surfactant is desirable as it maintains a high surface tension even when alkaline percentage is increased.


2018 ◽  
Vol 2018 ◽  
pp. 1-7
Author(s):  
Limin Zhang ◽  
Ning Li ◽  
Hui Xing ◽  
Rong Zhang ◽  
Kaikai Song

The effect of direct current (DC) on the wetting behavior of Cu substrate by liquid Ga–25In–13Sn alloy at room temperature is investigated using a sessile drop method. It is found that there is a critical value for current intensity, below which the decrease of contact angle with increasing current intensity is approximately linear and above which contact angle tends to a stable value from drop shape. Current polarity is a negligible factor in the observed trend. Additionally, the observed change in contact angles is translated into the corresponding change in solid-liquid interfacial tension using the equation of state for liquid interfacial tensions. The solid-liquid interfacial tension decreases under DC. DC-induced promotion of solute diffusion coefficient is likely to play an important role in determining the wettability and solid-liquid interfacial tension under DC.


Sign in / Sign up

Export Citation Format

Share Document