scholarly journals Hot Straining and Quenching and Partitioning of a TRIP-Assisted Steel: Microstructural Characterization and Mechanical Properties

2018 ◽  
Vol 941 ◽  
pp. 704-710
Author(s):  
Edwan Anderson Ariza ◽  
Jonathan Poplawsky ◽  
Wei Guo ◽  
André Paulo Tschiptschin
Keyword(s):  
Mechanical Properties ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Characterization ◽  
Atom Probe ◽  
Carbon Partitioning ◽  
Carbon Accumulation ◽  
Processing Route ◽  
Carbide Formation ◽  
Quenching And Partitioning

Advanced high strength steels (AHSS), with yield strengths over 300 MPa and tensile strengths exceeding 600 MPa, are becoming more noticeable in vehicle manufacturing. A novel processing route of a TRIP-assisted steel was developed. Characterization and modelling techniques were used to establish correlations between processing, microstructure and mechanical properties. Quenching and partitioning (Q&P) and a novel process of hot straining (HS) and Q&P (HSQ&P) treatments have been applied to a TRIP-assisted steel in a Gleeble ®3S50 thermo-mechanical simulator. The heat treatments involved intercritical annealing at 800 oC and a two-step Q&P heat treatment with a partitioning time of 100 s at 400 oC. The effects of high-temperature isothermal deformation on the carbon enrichment of austenite, carbide formation and the strain-induced transformation to ferrite (SIT) mechanism were investigated. Carbon partitioning from supersaturated martensite into austenite and carbide precipitation were confirmed by means of atom probe tomography (APT). Austenite carbon enrichment was clearly observed in all specimens, and in the HSQ&P samples it was slightly greater than in Q&P, suggesting an additional carbon partitioning to austenite from ferrite formed by the SIT phenomenon. By APT, the carbon accumulation at austenite/martensite interface was clearly observed. The newly developed combined process is promising as the transformation induced plasticity can contribute to the formability and energy absorption, contributing to fill the gap of the third generation of high-strength steels.

Innovation and Processing of Novel Tough Ductile Ultra-High Strength Steels through TMR-DQP Processing Route

2014 ◽  
Vol 783-786 ◽  
pp. 1009-1014 ◽  
Author(s):  
Mahesh C. Somani ◽  
David A. Porter ◽  
L. Pentti Karjalainen ◽  
Pasi Suikkanen ◽  
R.D.K. Misra
Keyword(s):  
Mechanical Properties ◽  
Physical Simulation ◽  
High Strength Steels ◽  
High Strength ◽  
Structural Steels ◽  
Processing Route ◽  
Quenching And Partitioning ◽  
Direct Quenching ◽  
Thermomechanical Rolling ◽  
Ultra High Strength Steels

Based on the recent concept of quenching and partitioning (Q&P), a novel TMR-DQP (thermomechanical rolling followed by direct quenching and partitioning) processing route has been established for the development of ultra-high strength structural steels with yield strengths ≈1100 MPa combined with good uniform and total elongations and impact toughness. Suitable compositions were designed based on high silicon and/or aluminium contents with or without small additions of Nb, Mo or Ni. The DQP parameters were established with the aid of physical simulation on a Gleeble simulator. Finally, the TMR-DQP processing route was designed for trials on a laboratory rolling mill. Metallographic studies showed that the desired martensite-austenite microstructures were achieved thus providing the targeted mechanical properties. The advantage of strained austenite in refining the martensite packets/blocks was clearly evident. No adverse effect of prolonged partitioning simulating the coiling stage has been noticed suggesting new possibilities for strip and plate products. Promising results in respect of microstructures and mechanical properties indicate that there are possibilities for developing tough ductile structural steels through the TMR-DQP route.

Application of Quenching-Partitioning-Tempering Process in Hot Rolled Plate Fabrication

2010 ◽  
Vol 654-656 ◽  
pp. 82-85 ◽  
Author(s):  
Shu Zhou ◽  
Ying Wang ◽  
Nai Lu Chen ◽  
Yong Hua Rong ◽  
Jian Feng Gu
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Significant Fraction ◽  
Rolled Plate ◽  
Quenching And Partitioning ◽  
Good Ductility ◽  
Hot Rolled ◽  
Rolled Plates

The quenching-partitioning-tempering (Q-P-T) process, based on the quenching and partitioning (Q&P) treatment, has been proposed for producing high strength steels containing significant fraction of film-like retained austenite and controlled amount of fine martensite laths. In this study, a set of Q-P-T processes for C-Mn-Si-Ni-Nb hot rolled plates are designed and realized. The steels with Q-P-T processes present a combination of high strength and relatively good ductility. The origin of such mechanical properties is revealed by microstructure characterization.

scholarly journals Microstructural characterization and mechanical properties of spot welded dissimilar advanced high strength steels

2021 ◽  
Author(s):  
Muhammad Sohaib Khan
Keyword(s):  
Mechanical Properties ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Characterization ◽  
Advanced High Strength Steels ◽  
Spot Welded

Microstructural characterization and mechanical properties of spot welded dissimilar advanced high strength steels

Effect of Processing Route on Mechanical Behavior of C-Mn Multiphase High Strength Cold Rolled Steel

2007 ◽  
Vol 539-543 ◽  
pp. 4375-4380
Author(s):  
Dagoberto Brandão Santos ◽  
Élida G. Neves ◽  
Elena V. Pereloma
Keyword(s):  
Electron Microscopy ◽  
Mechanical Properties ◽  
Mechanical Behavior ◽  
Quantitative Relationship ◽  
High Strength ◽  
Microstructural Characterization ◽  
Processing Route ◽  
Accelerated Cooling ◽  
Microstructural Parameters ◽  
Transmission Electron

The multiphase steels have complex microstructures containing polygonal ferrite, martensite, bainite, carbide and a small amount of retained austenite. This microstructure provides these steels with a high mechanical strength and good ductility. Different thermal cycles were simulated in the laboratory in order to create the microstructures with improved mechanical properties. The samples were heated to various annealing temperatures (740, 760 or 780°C), held for 300 s, and then quickly cooled to 600 or 500°C, where they were soaked for another 300 s and then submitted to the accelerated cooling process, with the rates in the range of 12-30°C/s. The microstructure was examined at the end of each processing route. The mechanical behavior evaluation was made by microhardness testing. The microstructural characterization involved optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM) with electron backscattering diffraction (EBSD) and transmission electron microscopy (TEM). The use of multiple regression analysis allowed the establishment of quantitative relationship between the microstructural parameters, cooling rates and mechanical properties of the steel.

Quenching and Partitioning of Ni-Added High Strength Steels

2007 ◽  
Vol 539-543 ◽  
pp. 4476-4481 ◽  
Author(s):  
F.C. Rizzo ◽  
A.R. Martins ◽  
John G. Speer ◽  
David K. Matlock ◽  
A. Clarke ◽  
...  
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Processing Parameters ◽  
Carbide Formation ◽  
X Ray Diffraction ◽  
Quenching And Partitioning ◽  
Steel Microstructure ◽  
Advanced High Strength Steels ◽  
Treatment Procedures

High strength steels containing significant fractions of retained austenite have been developed in recent years, and are the subject of growing commercial interest when associated with the TRIP phenomenon during deformation. A new process concept “quenching and partitioning” (Q&P) has been proposed by CSM/USA, and the results show the potential to create a new kind of steel microstructure with controlled amounts of retained austenite, enriched by carbon partitioning. Four steels containing C, Si, Mn, Ni, Cr and Mo, were designed with variation in the Ni and C content, aiming to decrease Bs temperature and to suppress carbide formation during the partitioning treatment. Several heat-treatment procedures were performed in specimens previously machined for tensile testing, while x-ray diffraction was used to determine the fraction of retained austenite. The tensile test results showed that except for the high C high Ni alloy, most of the processing conditions resulted in strengths superior to those of advanced high strength steels (AHSS), although it is importantly recognized that higher alloy additions were used in this study, in comparison with conventional AHSS grades.. A variety of strength and ductility combinations were observed, confirming the potential of the Q&P process and illustrating the strong influence of the final microstructure on the mechanical properties. Experimental results for samples partitioned at 400 °C indicate that higher ultimate tensile strength is associated with higher fraction of retained austenite for multiple heat treatments of each alloy investigated. The amount of retained austenite obtained was generally lower than that predicted by the model. Further studies are in progress to understand the influence of alloying and processing parameters (time/temperature) on the partitioning of carbon and precipitation of transition carbides.

scholarly journals Temperature Dependence of the Static and Dynamic Behaviour in a Quenching and Partitioning Processed Low-Si Steel

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 509 ◽  
Author(s):  
Florian Vercruysse ◽  
Carola Celada-Casero ◽  
Bernd M. Linke ◽  
Patricia Verleysen ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Dynamic Strain ◽  
Strain Rates ◽  
Trip Effect ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
Wide Range

Because of their excellent combination of strength and ductility, quenching and partitioning (Q & P) steels have a great chance of being added to the third generation of advanced high strength steels. The large ductility of Q & P steels arises from the presence of 10% to 15% of retained austenite which postpones necking due to the transformation induced plasticity (TRIP) effect. Moreover, Q & P steels show promising forming properties with favourable Lankford coefficients, while their planar anisotropy is low due to a weak texture. The stability of the metastable austenite is the key to obtain tailored properties for these steels. To become part of the newest generation of advanced high strength steels, Q & P steels have to preserve their mechanical properties at dynamic strain rates and over a wide range of temperatures. Therefore, in the present study, a low-Si Q & P steel was tested at temperatures from −40 °C to 80 °C and strain rates from 0.001 s−1 to 500 s−1. Results show that the mechanical properties are well-preserved at the lowest temperatures. Indeed, at −40 °C and room temperature, no significant loss of the deformation capacity is observed even at dynamic strain rates. This is attributed to the presence of a large fraction of austenite that is so (thermally) stable that it does not transform in the absence of deformation. In addition, the high stability of the austenite decreases the elongation at high test temperatures (80 °C). The additional adiabatic heating in the dynamic tests causes the largest reduction of the uniform strain for the samples tested at 80 °C. Quantification of the retained austenite fraction in the samples after testing confirmed that, at the highest temperature and strain rate, the TRIP effect is suppressed.

scholarly journals The Effect of Alloying on Mechanical Properties of Advanced High Strength Steels

2014 ◽  
Vol 59 (3) ◽  
pp. 1189-1192 ◽  
Author(s):  
L. Kučerová ◽  
H. Jirková ◽  
B. Mašek
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cooling Rate ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructure Development ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
Quenching And Partitioning Process ◽  
Effect Of Alloying

Abstract Quenching and partitioning process with incorporated incremental deformation was optimized for six high strength steels with various contents of carbon (0.4-0.6%), manganese (0.6-1.2), silicon (2-2.6%) and chromium (0.8-1.3%). The optimization was gradually done for each steel with respect to the final microstructures and properties. The effect of cooling rate, quenching and partitioning temperature on microstructure development was further investigated. Interesting combinations of mechanical properties were obtained, with tensile strength in the region of 1600-2400 MPa and ductility of 6-20%.

scholarly journals The Effect of Mn and Si on the Properties of Advanced High Strength Steels Processed by Quenching and Partitioning

2010 ◽  
Vol 654-656 ◽  
pp. 94-97 ◽  
Author(s):  
Bohuslav Mašek ◽  
Hana Jirková ◽  
Daniela Hauserova ◽  
Ludmila Kučerová ◽  
Danuše Klauberová
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Development ◽  
X Ray Diffraction ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
High Ultimate Strength

The concepts new types of materials are, for economic reasons, focused mainly on low alloyed steels with a good combination of strength and ductility. Suitable heat and thermo-mechanical treatments play an important role for the utilization of these materials. Different alloying strategies are used to influence phase transformations. The quenching and partitioning process (Q-P Process) is one of the heat treatment methods which can result in a high ultimate strength as well as a good ductility. However, these good properties can be obtained only if a sufficient amount of retained austenite is stabilized. The influence of different contents of manganese, silicon and chromium on microstructural development and mechanical properties were experimentally tested. Alloying elements were used to stabilize the retained austenite in the final microstructure and also to strengthen the solid solution. Ultimate strengths of over 2000MPa with ductility over 10% were reached after the optimization of the Q-P Process. The microstructures were analyzed using several microscopic methods; mechanical properties were determined by a tensile test and the volume fraction of the retained austenite was established by X-ray diffraction phase analysis.

An Appraisal of Direct Quenching for the Development and Processing of Novel Super-High Strength Steels

2016 ◽  
Vol 879 ◽  
pp. 1819-1827 ◽  
Author(s):  
Mahesh C. Somani ◽  
Jaakko I. Hannula ◽  
Antti J. Kaijalainen ◽  
Devesh K. Misra ◽  
David A. Porter
Keyword(s):  
Linear Regression Analysis ◽  
High Strength Steels ◽  
High Strength ◽  
Processing Route ◽  
Low Carbon ◽  
Martensitic Steels ◽  
Quenching And Partitioning ◽  
Direct Quenching ◽  
Bainitic Steels ◽  
Novel Processing

Recent interests in developing novel super-high strength steels have led to extensive research efforts in direct quenching with or without tempering (DQ, DQT) or combined with partitioning (DQP). Both strip and plate products have been targeted for different applications. For boron-microalloyed DQ/DQT steels, the ASTM A255 approach for predicting the hardenability was considered inapplicable. Fresh attempts were made to develop new hardenability models through non-linear regression analysis by dynamically varying both the boron factor and multiplying factors of most elements in the alloy factor. Based on the recent concept of quenching and partitioning (Q&P), a novel processing route comprising thermomechanical rolling followed by direct quenching and partitioning (TMR-DQP) has been established for the development of ultra-high strength structural steels with yield strengths ≈1100 MPa combined with good uniform and total elongations and impact toughness. Examples of recent advances made in DQ processing and associated challenges, such as those related to the bendability of low carbon martensitic-bainitic steels and influence of boron on the toughness of Nb-bearing martensitic steels are presented.

scholarly journals Microstructural characterization and mechanical properties of spot welded dissimilar advanced high strength steels

2021 ◽  
Author(s):  
Muhammad Sohaib Khan
Keyword(s):  
Mechanical Properties ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Characterization ◽  
Advanced High Strength Steels ◽  
Spot Welded

Microstructural characterization and mechanical properties of spot welded dissimilar advanced high strength steels

Sign in / Sign up

Export Citation Format

Share Document