Quenching and Partitioning of Ni-Added High Strength Steels

2007 ◽  
Vol 539-543 ◽  
pp. 4476-4481 ◽  
Author(s):  
F.C. Rizzo ◽  
A.R. Martins ◽  
John G. Speer ◽  
David K. Matlock ◽  
A. Clarke ◽  
...  
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Processing Parameters ◽  
Carbide Formation ◽  
X Ray Diffraction ◽  
Quenching And Partitioning ◽  
Steel Microstructure ◽  
Advanced High Strength Steels ◽  
Treatment Procedures

High strength steels containing significant fractions of retained austenite have been developed in recent years, and are the subject of growing commercial interest when associated with the TRIP phenomenon during deformation. A new process concept “quenching and partitioning” (Q&P) has been proposed by CSM/USA, and the results show the potential to create a new kind of steel microstructure with controlled amounts of retained austenite, enriched by carbon partitioning. Four steels containing C, Si, Mn, Ni, Cr and Mo, were designed with variation in the Ni and C content, aiming to decrease Bs temperature and to suppress carbide formation during the partitioning treatment. Several heat-treatment procedures were performed in specimens previously machined for tensile testing, while x-ray diffraction was used to determine the fraction of retained austenite. The tensile test results showed that except for the high C high Ni alloy, most of the processing conditions resulted in strengths superior to those of advanced high strength steels (AHSS), although it is importantly recognized that higher alloy additions were used in this study, in comparison with conventional AHSS grades.. A variety of strength and ductility combinations were observed, confirming the potential of the Q&P process and illustrating the strong influence of the final microstructure on the mechanical properties. Experimental results for samples partitioned at 400 °C indicate that higher ultimate tensile strength is associated with higher fraction of retained austenite for multiple heat treatments of each alloy investigated. The amount of retained austenite obtained was generally lower than that predicted by the model. Further studies are in progress to understand the influence of alloying and processing parameters (time/temperature) on the partitioning of carbon and precipitation of transition carbides.

scholarly journals The Effect of Mn and Si on the Properties of Advanced High Strength Steels Processed by Quenching and Partitioning

2010 ◽  
Vol 654-656 ◽  
pp. 94-97 ◽  
Author(s):  
Bohuslav Mašek ◽  
Hana Jirková ◽  
Daniela Hauserova ◽  
Ludmila Kučerová ◽  
Danuše Klauberová
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Microstructural Development ◽  
X Ray Diffraction ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
High Ultimate Strength

The concepts new types of materials are, for economic reasons, focused mainly on low alloyed steels with a good combination of strength and ductility. Suitable heat and thermo-mechanical treatments play an important role for the utilization of these materials. Different alloying strategies are used to influence phase transformations. The quenching and partitioning process (Q-P Process) is one of the heat treatment methods which can result in a high ultimate strength as well as a good ductility. However, these good properties can be obtained only if a sufficient amount of retained austenite is stabilized. The influence of different contents of manganese, silicon and chromium on microstructural development and mechanical properties were experimentally tested. Alloying elements were used to stabilize the retained austenite in the final microstructure and also to strengthen the solid solution. Ultimate strengths of over 2000MPa with ductility over 10% were reached after the optimization of the Q-P Process. The microstructures were analyzed using several microscopic methods; mechanical properties were determined by a tensile test and the volume fraction of the retained austenite was established by X-ray diffraction phase analysis.

scholarly journals Effect of Quenching and Partitioning Temperatures in the Q-P Process on the Properties of AHSS with Various Amounts of Manganese and Silicon

2012 ◽  
Vol 706-709 ◽  
pp. 2734-2739 ◽  
Author(s):  
Hana Jirková ◽  
Ludmila Kučerová ◽  
Bohuslav Mašek
Keyword(s):  
Tensile Strength ◽  
Retained Austenite ◽  
Isothermal Holding ◽  
Bainitic Ferrite ◽  
High Strength Steels ◽  
High Strength ◽  
Experimental Program ◽  
Quenching Temperature ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels

The use of the combined influence of retained austenite and bainitic ferrite to improve strength and ductility has been known for many years from the treatment of multiphase steels. Recently, the very fine films of retained austenite along the martensitic laths have also become the centre of attention. This treatment is called the Q-P process (quenching and partitioning). In this experimental program the quenching temperature and the isothermal holding temperature for diffusion carbon distribution for three advanced high strength steels with carbon content of 0.43 % was examined. The alloying strategies have a different content of manganese and silicon, which leads to various martensite start and finish temperatures. The model treatment was carried out using a thermomechanical simulator. Tested regimes resulted in a tensile strength of over 2000MPa with a ductility of above 14 %. The increase of the partitioning temperature influenced the intensity of martensite tempering and caused the decrease of tensile strength by 400MPa down to 1600MPa and at the same time more than 10 % growth of ductility occurred, increasing it to more than 20%.

Influence of the Processing Variables on the Microstructure Evolution of a Bainitic Carbide-Free Steel

2016 ◽  
Vol 879 ◽  
pp. 867-872 ◽  
Author(s):  
M.C. Taboada ◽  
I. Gutiérrez ◽  
D. Jorge-Badiola ◽  
S.M.C. van Bohemen ◽  
F. Hisker ◽  
...  
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
High Volume ◽  
X Ray Diffraction ◽  
Tempered Martensite ◽  
Trip Steels ◽  
Volume Fractions ◽  
Advanced High Strength Steels ◽  
Processing Variables

New trends focused on achieving higher performance steels has led to a so-called 3rd Generation Advanced High Strength Steels (AHSS), in which the typical polygonal ferrite found in TRIP steels as a matrix phase is replaced by harder phases as Carbide-Free Bainite (CFB) and/or (tempered) martensite. Besides, large volume fractions of retained austenite (R.A.) with adequate stability are aimed for to improve the formability of the steels. Si containing steels are regarded as the most suitable to retard cementite formation and consequently reach high volume fractions of RA. In this work, CFB annealing schedules were applied to dilatometer samples of Fe-0.22C-2.0Mn-1.3Si. The overaging temperature TB was varied between 390 oC and 480 oC, and other processing variables investigated were the austenitizing temperature Taus, and the overaging holding time tB. The annealed samples analyzed with LOM, FEG-SEM, EBSD and X-ray diffraction techniques show that markedly different complex microstructures made up of bainite, ferrite, MA phase and retained austenite (R.A) are accomplished depending on the specific thermal cycle. These results are described in detail and discussed in relation to the dilatometry measurements.

scholarly journals Addressing Retained Austenite Stability in Advanced High Strength Steels

2013 ◽  
Vol 738-739 ◽  
pp. 212-216 ◽  
Author(s):  
Elena V. Pereloma ◽  
Azdiar A. Gazder ◽  
Ilana B. Timokhina
Keyword(s):  
Retained Austenite ◽  
Mechanical Stability ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Processing Parameters ◽  
Advanced High Strength Steels ◽  
Austenite Stability ◽  
Retained Austenite Stability ◽  
Size And Morphology

Advances in the development of new high strength steels have resulted in microstructures containing significant volume fractions of retained austenite. The transformation of retained austenite to martensite upon straining contributes towards improving the ductility. However, in order to gain from the above beneficial effect, the volume fraction, size, morphology and distribution of the retained austenite need to be controlled. In this regard, it is well known that carbon concentration in the retained austenite is responsible for its chemical stability, whereas its size and morphology determines its mechanical stability. Thus, to achieve the required mechanical properties, control of the processing parameters affecting the microstructure development is essential.

scholarly journals Temperature Dependence of the Static and Dynamic Behaviour in a Quenching and Partitioning Processed Low-Si Steel

Metals ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 509 ◽  
Author(s):  
Florian Vercruysse ◽  
Carola Celada-Casero ◽  
Bernd M. Linke ◽  
Patricia Verleysen ◽  
Roumen H. Petrov
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Dynamic Strain ◽  
Strain Rates ◽  
Trip Effect ◽  
Quenching And Partitioning ◽  
Advanced High Strength Steels ◽  
Wide Range

Because of their excellent combination of strength and ductility, quenching and partitioning (Q & P) steels have a great chance of being added to the third generation of advanced high strength steels. The large ductility of Q & P steels arises from the presence of 10% to 15% of retained austenite which postpones necking due to the transformation induced plasticity (TRIP) effect. Moreover, Q & P steels show promising forming properties with favourable Lankford coefficients, while their planar anisotropy is low due to a weak texture. The stability of the metastable austenite is the key to obtain tailored properties for these steels. To become part of the newest generation of advanced high strength steels, Q & P steels have to preserve their mechanical properties at dynamic strain rates and over a wide range of temperatures. Therefore, in the present study, a low-Si Q & P steel was tested at temperatures from −40 °C to 80 °C and strain rates from 0.001 s−1 to 500 s−1. Results show that the mechanical properties are well-preserved at the lowest temperatures. Indeed, at −40 °C and room temperature, no significant loss of the deformation capacity is observed even at dynamic strain rates. This is attributed to the presence of a large fraction of austenite that is so (thermally) stable that it does not transform in the absence of deformation. In addition, the high stability of the austenite decreases the elongation at high test temperatures (80 °C). The additional adiabatic heating in the dynamic tests causes the largest reduction of the uniform strain for the samples tested at 80 °C. Quantification of the retained austenite fraction in the samples after testing confirmed that, at the highest temperature and strain rate, the TRIP effect is suppressed.

scholarly journals In Situ Determination of Phase Stress States in an Unstable Medium Manganese Duplex Steel Studied by High-Energy X-ray Diffraction

Metals ◽  
2020 ◽  
Vol 10 (10) ◽  
pp. 1335
Author(s):  
Mathias Lamari ◽  
Sébastien Y. P. Allain ◽  
Guillaume Geandier ◽  
Jean-Christophe Hell ◽  
Astrid Perlade ◽  
...  
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
High Energy ◽  
Internal Stresses ◽  
X Ray Diffraction ◽  
X Ray ◽  
Advanced High Strength Steels ◽  
Stress States

Duplex medium Mn steels are high-potential advanced high-strength steels (AHSS) for automotive construction. Their excellent forming properties stem from the specific stress partitioning between their constituting phases during deformation, namely the ferritic matrix, unstable retained austenite, and strain-induced fresh martensite. The stability of the retained austenite and the 3D stress tensors of each phase are determined simultaneously in this work by in situ high energy X-ray diffraction on synchrotron beamline during a tensile test. The role of internal stresses inherited from the manufacturing stage are highlighted for the first time as well as new insights to understand the origin of the serrations shown by these alloys.

scholarly journals Heat Treatment Design for a QP Steel: Effect of Partitioning Temperature

Metals ◽  
2021 ◽  
Vol 11 (7) ◽  
pp. 1136
Author(s):  
Marcel Carpio ◽  
Jessica Calvo ◽  
Omar García ◽  
Juan Pablo Pedraza ◽  
José María Cabrera
Keyword(s):  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Tensile Tests ◽  
Quenching Temperature ◽  
Advanced High Strength Steels ◽  
New Family ◽  
Automotive Parts ◽  
Fresh Martensite ◽  
Industry Needs

Designing a new family of advanced high-strength steels (AHSSs) to develop automotive parts that cover early industry needs is the aim of many investigations. One of the candidates in the 3rd family of AHSS are the quenching and partitioning (QP) steels. These steels display an excellent relationship between strength and formability, making them able to fulfill the requirements of safety, while reducing automobile weight to enhance the performance during service. The main attribute of QP steels is the TRIP effect that retained austenite possesses, which allows a significant energy absorption during deformation. The present study is focused on evaluating some process parameters, especially the partitioning temperature, in the microstructures and mechanical properties attained during a QP process. An experimental steel (0.2C-3.5Mn-1.5Si (wt%)) was selected and heated according to the theoretical optimum quenching temperature. For this purpose, heat treatments in a quenching dilatometry and further microstructural and mechanical characterization were carried out by SEM, XRD, EBSD, and hardness and tensile tests, respectively. The samples showed a significant increment in the retained austenite at an increasing partitioning temperature, but with strong penalization on the final ductility due to the large amount of fresh martensite obtained as well.

scholarly journals Carbon Redistribution and Microstructural Evolution Study during Two-Stage Quenching and Partitioning Process of High-Strength Steels by Modeling

Materials ◽  
2018 ◽  
Vol 11 (11) ◽  
pp. 2302 ◽  
Author(s):  
Yilin Wang ◽  
Huicheng Geng ◽  
Bin Zhu ◽  
Zijian Wang ◽  
Yisheng Zhang
Keyword(s):  
Retained Austenite ◽  
Volume Fraction ◽  
High Strength Steels ◽  
High Strength ◽  
Simulation Method ◽  
Low Carbon ◽  
Two Stage ◽  
Quenching And Partitioning ◽  
Carbon Redistribution ◽  
Carbon Martensite

The application of the quenching and partitioning (Q-P) process on advanced high-strength steels improves part ductility significantly with little decrease in strength. Moreover, the mechanical properties of high-strength steels can be further enhanced by the stepping-quenching-partitioning (S-Q-P) process. In this study, a two-stage quenching and partitioning (two-stage Q-P) process originating from the S-Q-P process of an advanced high-strength steel 30CrMnSi2Nb was analyzed by the simulation method, which consisted of two quenching processes and two partitioning processes. The carbon redistribution, interface migration, and phase transition during the two-stage Q-P process were investigated with different temperatures and partitioning times. The final microstructure of the material formed after the two-stage Q-P process was studied, as well as the volume fraction of the retained austenite. The simulation results indicate that a special microstructure can be obtained by appropriate parameters of the two-stage Q-P process. A mixed microstructure, characterized by alternating distribution of low carbon martensite laths, small-sized low-carbon martensite plates, retained austenite and high-carbon martensite plates, can be obtained. In addition, a peak value of the volume fraction of the stable retained austenite after the final quenching is obtained with proper partitioning time.

Application of Quenching-Partitioning-Tempering Process in Hot Rolled Plate Fabrication

2010 ◽  
Vol 654-656 ◽  
pp. 82-85 ◽  
Author(s):  
Shu Zhou ◽  
Ying Wang ◽  
Nai Lu Chen ◽  
Yong Hua Rong ◽  
Jian Feng Gu
Keyword(s):  
Mechanical Properties ◽  
Retained Austenite ◽  
High Strength Steels ◽  
High Strength ◽  
Significant Fraction ◽  
Rolled Plate ◽  
Quenching And Partitioning ◽  
Good Ductility ◽  
Hot Rolled ◽  
Rolled Plates

The quenching-partitioning-tempering (Q-P-T) process, based on the quenching and partitioning (Q&P) treatment, has been proposed for producing high strength steels containing significant fraction of film-like retained austenite and controlled amount of fine martensite laths. In this study, a set of Q-P-T processes for C-Mn-Si-Ni-Nb hot rolled plates are designed and realized. The steels with Q-P-T processes present a combination of high strength and relatively good ductility. The origin of such mechanical properties is revealed by microstructure characterization.

Sign in / Sign up

Export Citation Format

Share Document