The Effect of Thermal Aging on Mechanical Properties and Morphological Properties of Thermoplastic Vulcanizates Based on Natural Rubber and Polystyrene

2020 ◽  
Vol 990 ◽  
pp. 262-266
Author(s):  
Prathumrat Nu-Yang ◽  
Atiwat Wiriya-Amornchai ◽  
Jaehoon Yoon ◽  
Chainat Saechau ◽  
Poom Rattanamusik
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Impact Strength ◽  
Natural Rubber ◽  
Thermal Aging ◽  
Morphological Properties ◽  
Vulcanized Rubber ◽  
Thermoplastic Vulcanizates ◽  
Internal Mixer ◽  
Processing Properties

Thermoplastic vulcanizates or TPVs is a type of materials exhibiting excellent properties between thermoplastic and elastomer by combining the characteristics of vulcanized rubber with the processing properties of thermoplastics. This research aims to study the effect of thermal aging on the morphology and mechanical properties of thermoplastic vulcanizates (TPVs) based on a mixture of natural rubber (NR) and polystyrene (PS). TPVs samples were prepared using the internal mixer at a mass ratio of NR/PS 70/30, 50/50, 30/70 and 0/100. Tensile properties and impact strength showed that when the amount of NR increased tends of impact strength and elongation at break increased but tends of tensile strength decreased. On the other hand, tends of tensile strength for thermal aging at 70°C for 3 days increased when the amount of PS increase. The blending ratio of NR / PS at 70/30 is the best. It gave a worthy increase from 19.94 MPa to be 25.56 MPa (28.18%).

Effect of Curing System on Morphological, Rheological, Thermal and Mechanical Properties of Thermoplastic Vulcanizates Based on Epoxidized Natural Rubber and Polypropylene

2012 ◽  
Vol 602-604 ◽  
pp. 690-695
Author(s):  
Hua Dong Wang ◽  
Rui Wang ◽  
Mao Fang Huang ◽  
Qi Yang
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Epoxidized Natural Rubber ◽  
Thermal And Mechanical Properties ◽  
Rheological Analysis ◽  
Elongation At Break ◽  
Thermoplastic Vulcanizates ◽  
Internal Mixer

Thermoplastic vulcanizates (TPVs) based on epoxidized natural rubber (ENR) and polypropylene (PP) were prepared in an internal mixer at 180°C. The effects of curing systems (i.e., sulfur and peroxide) on morphological, rheological, thermal and mechanical properties were studied. It is found that the sulfur cured TPVs show higher tensile strength, tear strength and elongation at break than those cured with the DCP systems. The rheological analysis indicates that TPVs cured with DCP system show lower apparent shear viscosity than those with sulfur system. SEM studies show that TPVs vulcanized with DCP system exhibit smaller and finely dispersed rubber domains, which provides it higher thermal stability than sulfur cured TPVs.

Mechanochemical Devulcanization of Vulcanized Gum Natural Rubber

2005 ◽  
Vol 21 (3) ◽  
pp. 183-199
Author(s):  
G.K. Jana ◽  
C.K. Das
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Three Dimensional ◽  
Elongation At Break ◽  
Tear Strength ◽  
Vulcanized Rubber ◽  
Dimensional Network ◽  
Polymeric Chains ◽  
Cure Time

De-vulcanization of vulcanized elastomers represents a great challenge because of their three-dimensional network structure. Sulfur-cured gum natural rubbers containing three different sulfur/accelerator ratios were de-vulcanized by thio-acids. The process was carried out at 90 °C for 10 minutes in an open two-roll cracker-cum-mixing mill. Two concentrations of de-vulcanizing agent were tried in order to study the cleavage of the sulfidic bonds. The mechanical properties of the re-vulcanized rubber (like tensile strength, modulus, tear strength and elongation at break) were improved with increasing concentrations of de-vulcanizing agent, because the crosslink density increased. A decrease in scorch time and in optimum cure time and an increase in the state of cure were observed when vulcanized rubber was treated with high amounts of de-vulcanizing agent. The temperature of onset of degradation was also increased with increasing concentration of thio-acid. DMA analysis revealed that the storage modulus increased on re-vulcanization. From IR spectroscopy it was observed that oxidation of the main polymeric chains did not occur at the time of high temperature milling. Over 80% retention of the original mechanical properties (like tensile strength, modulus, tear strength and elongation at break) of the vulcanized natural rubber was achieved by this mechanochemical process.

Mixing Methods Influencing on Properties of Epoxidized Natural Rubber/Polypropylene Thermoplastic Vulcanizates

2013 ◽  
Vol 844 ◽  
pp. 109-112 ◽  
Author(s):  
Chesidi Hayichelaeh ◽  
Charoen Nakason ◽  
Anoma Thitithammawong
Keyword(s):  
Mechanical Properties ◽  
Natural Rubber ◽  
Dynamic Mechanical Properties ◽  
Epoxidized Natural Rubber ◽  
Melt Mixing ◽  
Dynamic Mechanical ◽  
Thermoplastic Vulcanizates ◽  
Mixing Method ◽  
Internal Mixer

Epoxidized natural rubber (ENR)/Polypropylene (PP) thermoplastic vulcanizates were prepared by melt mixing method in an internal mixer. Influences of different mixing methods for incorporation of processing oil into the TPVs on tensile and dynamic mechanical properties of the TPVs and crystallinity of the PP were investigated. Results show that distribution of processing oil in the ENR/PP TPV is important due to the processing oil can promote and in the same time can interrupt an improvement in elastomeric properties of the TPV. Incorporation of processing oil into the ENR phase by preparation of oil extended ENR (the mixing method 1) before mixing with the PP was the better way to produce the TPV. It promoted the TPV with superior tensile and dynamic mechanical properties than the TPVs prepared from the mixing method 2 and 3 in which the processing oil was directly added into the PP phase. Furthermore, the TPV from the mixing method 1 had less effect of processing oil on the PP crystallization.

Preparation and Properties of Sponge Rubber Based on Natural Rubber and Cassava Starch

2014 ◽  
Vol 931-932 ◽  
pp. 68-72
Author(s):  
Komsun Temna ◽  
Nitinart Saetung ◽  
Anuwat Saetung
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Cassava Starch ◽  
Interfacial Interaction ◽  
Morphological Properties ◽  
Elongation At Break ◽  
Cure Time ◽  
The Difference ◽  
Cure Characteristic

In this work, the sponge rubbers based on cassava starch masterbatch in latex phase with the difference technique (non-gelatinized and gelatinized cassava starch) were preformed. The cassava starch contents from 0 to 70 phr were also studied. The cure characteristic, mechanical and morphological properties were investigated. It was found that the scorch time and cure time were increased with an increasing of cassava starch contents in both techniques. The mechanical properties i.e., tensile strength, elongation at break and tear strength were decreased with an increasing of cassava starch contents, except 500% modulus. However, the sponge based on gelatinized technique gave the better mechanical properties than that of non-gelatinized cassava starch. The SEM micrographs of sponge NR from gelatinized technique were also able to confirm a good interfacial interaction between hydrophilic cassava starch and hydrophobic NR.

Cellular Bi2O3/natural rubber composites for light-weight and lead-free gamma-shielding materials and their properties under gamma irradiation

2021 ◽  
pp. 0021955X2199735
Author(s):  
Phakamat Limarun ◽  
Teerasak Markpin ◽  
Narongrit Sombatsompop ◽  
Ekachai Wimolmala ◽  
Kiadtisak Saenboonruang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Gamma Irradiation ◽  
Attenuation Coefficient ◽  
Tensile Modulus ◽  
Lead Free ◽  
Morphological Properties ◽  
Light Weight ◽  
Elongation At Break

This work investigated the effects of a radiation-protective filler, namely bismuth oxide (Bi2O3), and blowing agents, namely azodicarbonamide (ADC) and oxy-bis (benzene sulfonyl) hydrazide (OBSH), on gamma attenuation and the mechanical, physical, and morphological properties of cellular natural rubber (NR) composites for potential use as light-weight and lead-free gamma-shielding materials. The contents of Bi2O3 were varied from 100 to 300 and 500 parts per hundred of rubber by weight (phr) and the contents of ADC or OBSH were varied from 0 to 8 and 16 phr. The results indicated that the addition of Bi2O3 enhanced the overall gamma-shielding ability, density, tensile modulus, and hardness (Shore OO), but lowered the tensile strength and elongation at break. On the other hand, the addition of ADC or OBSH resulted in decreases in the density, linear attenuation coefficient ( μ), and overall tensile properties but an increase in the mass attenuation coefficient ( μm), with ADC producing better mechanical properties than samples with OBSH. In addition, investigations on the properties of the cellular Bi2O3/NR composites under additional 35 kGy and 70 kGy gamma irradiation revealed that the irradiated samples had increased density, tensile modulus, and hardness (Shore OO), but decreased tensile strength, elongation at break, and μm after such ageing. In conclusion, the overall results suggested that the developed cellular Bi2O3/NR composites not only had efficient and promising gamma-shielding and mechanical properties but also offered comfort and light-weight to users, which could potentially reduce discomforts caused by wearing heavier conventional radiation-protective equipment.

Properties of Compatibilized SAN/NR Blends

2012 ◽  
Vol 488-489 ◽  
pp. 62-66
Author(s):  
Jareenuch Rojsatean ◽  
Supakij Suttireungwong ◽  
Manus Seadan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Electron Microscope ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Melt Blending ◽  
Elongation At Break ◽  
Reactive Agents ◽  
Internal Mixer ◽  
Scanning Electron

The blend of poly(styrene-co-acrylonitrile) (SAN) and natural rubber (NR) is immiscible and incompatible which lead to poor mechanical properties. Many methods can be carried out to improve the compatibility. In this work, the potential of various reactive compatibilizers in SAN and NR blend was explored. The morphological and mechanical properties were compared. The melt blending of SAN and NR were prepared in an internal mixer with various types of reactive agent such as styrene-co-maleic anhydride (SMA), maleic anhydride (MA), peroxide and mixed reactive agents. The morphological textures of the blends were investigated by scanning electron microscope. Mechanical properties including tensile strength, impact strength and elongation at break were measured. The results of morphological observations revealed that SAN/NR blend with reactive agent, the mixture of SMA and MA show the smallest and the most uniform dispersed NR particles, where the size of NR particle is about 1 µm. The mechanical properties of the blends revealed impact strength and elongation at break were increased with addition of reactive agents. SAN/NR blend with the mixture of SMA and MA showed the highest elongation at break but it had lower impact strength than the blend with SMA.

Physical Properties of Rice Husk Fiber/Natural Rubber Composites

2011 ◽  
Vol 410 ◽  
pp. 90-93 ◽  
Author(s):  
Ladawan Srisuwan ◽  
Kasama Jarukumjorn ◽  
Nitinat Suppakarn
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Rubber ◽  
Rice Husk ◽  
Crosslink Density ◽  
Morphological Properties ◽  
Rubber Composites ◽  
Elongation At Break ◽  
Natural Rubber Composites ◽  
Reinforcing Filler

In this study, rice husk fiber (RHF) was used as a reinforcing filler for natural rubber (NR). NR composites were prepared at various RHF contents, i.e., 10, 20, 30, 40 and 50 phr. Sulfur conventional vulcanization was used. Effect of RHF content on cure characteristics, mechanical properties and morphological properties of NR composites were investigated. The results showed that scorch and cure times of RHF/NR composites were not affected by increasing RHF content. Crosslink density, tensile strength, elongation at break and tear strength of NR composites slightly decreased with increasing RHF content whereas M100 and M300 of the composites slightly increased with increasing RHF content.

Physical and Mechanical Properties of Thermoplastic Natural Rubber (TPNR) Nanocomposites

2012 ◽  
Vol 576 ◽  
pp. 394-397 ◽  
Author(s):  
Noor Azlina Hassan ◽  
Hassan Norita ◽  
Sahrim Haji Ahmad ◽  
Rozaidi Rasid ◽  
Hazleen Anuar ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Maleic Anhydride ◽  
Natural Rubber ◽  
Physical And Mechanical Properties ◽  
Melt Blending ◽  
Mixing Parameters ◽  
Blending Method ◽  
Thermoplastic Natural Rubber ◽  
Internal Mixer

Thermoplastic natural rubber (TPNR) nanocomposites were prepared by melt blending method with the optimum mixing parameters (140oC, 100 rpm, 12 min) using internal mixer (Haake 600 P). The aim of this work is to study the effects of organo-montmorillonite (OMMT) on the physical and mechanical properties of TPNR with and without coupling agent (maleic anhydride grafted polyethylene, MA-PE). Significant improvement in tensile strength and modulus of TPNR nanocomposites were obtained with the presence of MA-PE.

Improving Mechanical Properties of Poly-β-Hydroxybutyrate-co-β-Hydroxyvalerate by Blending with Natural Rubber and Epoxidized Natural Rubber

2014 ◽  
Vol 983 ◽  
pp. 179-182 ◽  
Author(s):  
Maneewong Chutamas ◽  
Sunthornvarabhas Jackapon ◽  
Joong Kim Hyun ◽  
Sriroth Klanarong
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Maleic Anhydride ◽  
Impact Strength ◽  
Natural Rubber ◽  
Benzoyl Peroxide ◽  
Storage Modulus ◽  
Epoxidized Natural Rubber ◽  
Mixed Coding ◽  
Elastic Polymer

Poly-β-hydroxybutyrate-co-β-hydroxyvalerate (PHBV) is a bacterial-synthesized biopolymer. Moreover, PHBV is a biodegradable, it is an interesting biopolymer for disposable products. PHBV is difficult to process due to its low toughness, an elastic polymer such as natural rubber is introduced to develop toughness. In this experiment, PHBV mechanical properties were improved by blending with natural rubber (NR) and epoxidized natural rubber (ENR). The NR/PHBV and ENR/PHBV blends with the same ratio of 10/90 (wt/wt) could be extruded, whereas other conditions could not. This ratio was then used throughout this study to examine effect of maleic anhydride (MA) and benzoyl peroxide (BPO) to improve toughness of the blends. Result showed at composition where 1.0 % (wt/wt) MA and 0.05 % (wt/wt) BPO was mixed (coding EPMB2), several aspects of mechanical properties were improved. The blend, EPMB2 revealed the highest impact strength, significantly improved of elongation but drastically decreased of tensile strength. Storage modulus slightly decreased, tangent delta significantly increased when compared with neat PHBV.

Influence of Natural Rubber/Poly (3-Trimethoxysilyl Propyl Methacrylate) Core-Shell Compatibilizer on Dynamic, Mechanical and Morphological Properties of PMMA/ENR Blends

2013 ◽  
Vol 747 ◽  
pp. 538-541 ◽  
Author(s):  
Suparat Nooma ◽  
Rathanawan Magaraphan
Keyword(s):  
Mechanical Properties ◽  
Impact Strength ◽  
Natural Rubber ◽  
Testing Machine ◽  
Morphological Properties ◽  
Core Shell ◽  
Melt Mixing ◽  
Propyl Methacrylate ◽  
Dynamic Mechanical ◽  
The Impact

In this work, epoxidized natural rubber (ENR) is used to improve the impact strength of poly (methyl methacrylate) (PMMA). The natural rubber with poly (3-trimethoxysilyl propyl methacrylate) core-shell (adNR), prepared by admicellar polymerization, is used as the compatibilizer for PMMA/ENR blends which were prepared through melt mixing in a twin screw extruder. The effects of ENR and adNR contents on impact property were investigated by pendulum impact tester. The impact strength increased with ENR and adNR contents. The morphology on the fracture surfaces were demonstrated by using field emission electron microscope (FE-SEM), which showed the compatibility between ENR, adNR and PMMA. Furthermore, the effects of ENR and adNR contents on dynamic and mechanical properties were examined by dynamic mechanical analyzer and universal testing machine, respectively. The results illustrated that the incorporation of the adNR affected the dynamic and mechanical properties of the blends.

Sign in / Sign up

Export Citation Format

Share Document