scholarly journals Identification of Flow Properties of Fine Powders Based on Dynamic Flow Characteristics Obtained by Stirring and Aerating

2015 ◽  
Vol 52 (10) ◽  
pp. 576-584 ◽  
Author(s):  
Hiroshi Nagashima ◽  
Toshifumi Ishikura
Keyword(s):  
Flow Characteristics ◽  
Flow Properties ◽  
Dynamic Flow ◽  
Fine Powders

Moisture Dependent Dynamic Flow Properties of Coconut Flours

2016 ◽  
Vol 12 (6) ◽  
pp. 577-585 ◽  
Author(s):  
M. R. Manikantan ◽  
R. P. Kingsly Ambrose ◽  
Sajid Alavi
Keyword(s):  
Moisture Content ◽  
Normal Stress ◽  
Flow Characteristics ◽  
Coconut Oil ◽  
Friction Angle ◽  
Wall Friction ◽  
Flow Properties ◽  
Dynamic Flow ◽  
Virgin Coconut Oil ◽  
Air Velocity

Abstract The dynamic flow properties of two important coproducts of virgin coconut oil (VCO) i. e. coconut milk residue flour (MRF) and VCO cake flour (CF) were studied. The basic flowability energy of CF was higher than MRF and increased with moisture content. The change in compressibility and shear stress, with applied normal stress and moisture content, indicated that these powders are highly cohesive. For both flours, the energy required to make the powder flow increased with moisture at all experimental air velocity. Moisture did not significantly influence the cohesion and unconfined yield strength of MRF, whereas for CF there was significant effect due to the presence of moisture. The wall friction angle of both the flours increased significantly with moisture and decreased with applied normal stress. The results from this study indicated that, both CF and MRF at around 4.00 % moisture content had better flow characteristics than at higher moisture levels.

scholarly journals Analysis of Flow Characteristics and Effects of Turbulence Models for the Butterfly Valve

2021 ◽  
Vol 11 (14) ◽  
pp. 6319
Author(s):  
Sung-Woong Choi ◽  
Hyoung-Seock Seo ◽  
Han-Sang Kim
Keyword(s):  
Turbulence Model ◽  
Dissipation Rate ◽  
Flow Characteristics ◽  
Turbulence Models ◽  
Flow Properties ◽  
Nominal Diameter ◽  
Large Pressure ◽  
Sst Model ◽  
Turbulence Effect ◽  
Valve Opening

In the present study, the flow characteristics of butterfly valves with different sizes DN 80 (nominal diameter: 76.2 mm), DN 262 (nominal diameter: 254 mm), DN 400 (nominal diameter: 406 mm) were numerically investigated under different valve opening percentages. Representative two-equation turbulence models of two-equation k-epsilon model of Launder and Sharma, two-equation k-omega model of Wilcox, and two-equation k-omega SST model of Menter were selected. Flow characteristics of butterfly valves were examined to determine turbulence model effects. It was determined that increasing turbulence effect could cause many discrepancies between turbulence models, especially in areas with large pressure drop and velocity increase. In addition, sensitivity analysis of flow properties was conducted to determine the effect of constants used in each turbulence model. It was observed that the most sensitive flow properties were turbulence dissipation rate (Epsilon) for the k-epsilon turbulence model and turbulence specific dissipation rate (Omega) for the k-omega turbulence model.

Beyond Volumetrics: Unconventional Petrophysics for Efficient Resource Appraisal (Example from the Khazzan Field, Sultanate of Oman)

2015 ◽  
Author(s):  
David R. Spain ◽  
German D. Merletti ◽  
William Dawson
Keyword(s):  
Gas Permeability ◽  
Stress Profile ◽  
Tight Gas ◽  
Well Performance ◽  
Flow Properties ◽  
Dynamic Flow ◽  
Stress Regime ◽  
Flow Units ◽  
Fluid Saturation ◽  
Rock Typing

Abstract The Middle East region holds substantial resources of unconventional tight gas and shale gas. The efficient extraction of these resources requires significant technology and expertise across numerous disciplines, including reservoir description and geomechanical characterization, hydraulic fracture modelling and design, advanced numerical simulation capabilities, sensor and surveillance technologies, and tightly integrated workflows. The effective application of these integrated subsurface and completion workflows leads to improved capital efficiency and well performance through increased well potential, increased ultimate recovery, and reduced costs. Key elements include dynamic rock typing to highlight potential flow units that will maximize gas deliverability, geomechanical modelling to provide a calibrated stress profile, and an integrated model that demonstrates the importance of understanding both dynamic flow properties and geomechanical response in complex tectonic environments. Dynamic rock typing focuses on using both depositional and petrophysical properties including rock type, porosity, and effective gas permeability at reservoir conditions to divide the reservoir into flow units in the context of their saturation history. The geomechanical profiling generates a tectonics-corrected minimum horizontal stress (SHmin) and the net confining stress (NCS). The rock-log-test calibration requires the evaluation and integration of subsurface fracture tests, including After-Closure Analysis (ACA), Data Fracs and Micro Fracs. All three involve different injection volumes and sampled reservoir volumes. Tight gas petrophysical studies must go “beyond volumetrics”, and should consider not only the static (storage) and dynamic (flow) properties within the context of the petroleum system and evolution of the current day pore geometry and fluid saturation distribution, but also the geomechanical stress regime and its implications for efficient completion optimization. Alternative interpretations test the range of uncertainty and are useful in designing field trials and surveillance strategies to reduce the subsurface uncertainty and to mitigate development risks.

Numerical Investigation of Positive Displacement Rotary Lobe Pump With Twisted Rotors

2014 ◽  
Author(s):  
Xiaojun Jiang ◽  
Yi Li ◽  
Zhaohui He ◽  
Cui Baoling ◽  
Wenlong Dong
Keyword(s):  
Flow Structure ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Internal Flow ◽  
Dynamic Flow ◽  
Flow Fluctuation ◽  
Flow Field Characteristics ◽  
Lobe Pump ◽  
The Impact

The three-dimensional flow field characteristics are obtained by performing numerical simulation of flow in a lobe pump with twisted rotors. The relationship between the dynamic flow structure and the flow fluctuation is explored. Actually, the viscous incompressible Navier-Stokes equations are solved within an unsteady flow model. The dynamic mesh technique is applied to obtain the dynamic flow structure. By comparing the simulated results of straight rotor with those of twisted rotor, the effect of rotor shape on the flow fluctuation was revealed. Finally, the impact of the lobes number of rotors on flow pulsations is discussed. The results show that there is an intrinsic relationship between the flow fluctuation and the vortex in the lobe pump. The use of twisted rotors can effectively improve the internal flow characteristics of lobe pump and reduce flow fluctuation. With the increase of the number of lobes, the lobe pump output is more stable and capacity has been improved.

Using Flow Properties to Solve Flow Problems with Hard-to-Handle Powders in the Ceramics Industry

2008 ◽  
Vol 591-593 ◽  
pp. 620-627
Author(s):  
Herman Purutyan ◽  
Alfredo del Campo ◽  
Roger A. Barnum
Keyword(s):  
Titanium Dioxide ◽  
Cohesive Strength ◽  
Particle Sizes ◽  
Flow Properties ◽  
Handling System ◽  
Flow Problems ◽  
Fine Powders ◽  
Common Problems ◽  
Ceramic Manufacturing ◽  
Ceramics Industry

Many processes in ceramic manufacturing require handling of fine powders with particle sizes down to sub-micron range. Problems that are often experienced with these powders, such as stoppages and/or surges, can be predicted and prevented by first measuring relevant flow properties of these powders, and then using these properties to design a handling system. In this paper we will review common problems with handling such powders and the relevant flow properties tests, such as permeability, compressibility, cohesive strength and friction, as well as how these properties can be used to prevent and solve problems. Issues related to handling titanium dioxide (TiO2) will be used as an illustration.

scholarly journals On the Measurement and Modeling of High-Pressure Flows in Poppet Valves Under Steady-State and Transient Conditions

2017 ◽  
Vol 139 (7) ◽  
Author(s):  
Stephan Mohr ◽  
Henry Clarke ◽  
Colin P. Garner ◽  
Neville Rebelo ◽  
Andrew M. Williams ◽  
...  
Keyword(s):  
Steady State ◽  
Transient Flow ◽  
Three Dimensional ◽  
Flow Characteristics ◽  
Valve Lift ◽  
Transient Pressure ◽  
Dynamic Flow ◽  
Steady State Flow ◽  
State Flow ◽  
Piston Cylinder

Flow coefficients of intake valves and port combinations were determined experimentally for a compressed nitrogen engine under steady-state and dynamic flow conditions for inlet pressures up to 3.2 MPa. Variable valve timing was combined with an indexed parked piston cylinder unit for testing valve flows at different cylinder volumes while maintaining realistic in-cylinder transient pressure profiles by simply using a fixed area outlet orifice. A one-dimensional modeling approach describing three-dimensional valve flow characteristics has been developed by the use of variable flow coefficients that take into account the propagation of flow jets and their boundaries as a function of downstream/upstream pressure ratios. The results obtained for the dynamic flow cases were compared with steady-state results for the cylinder to inlet port pressure ratios ranges from 0.18 to 0.83. The deviation of flow coefficients for both cases is discussed using pulsatile flow theory. The key findings include the followings: (1) for a given valve lift, the steady-state flow coefficients fall by up to 21% with increasing cylinder/manifold pressure ratios within the measured range given above and (2) transient flow coefficients deviated from those measured for the steady-state flow as the valve lift increases beyond a critical value of approximately 0.5 mm. The deviation can be due to the insufficient time of the development of steady-state boundary layers, which can be quantified by the instantaneous Womersley number defined by using the transient hydraulic diameter. We show that it is possible to predict deviations of the transient valve flow from the steady-state measurements alone.

Flow properties of fine powders in powder coating

Particuology ◽  
2010 ◽  
Vol 8 (1) ◽  
pp. 19-27 ◽  
Author(s):  
Qing Huang ◽  
Hui Zhang ◽  
Jesse Zhu
Keyword(s):  
Powder Coating ◽  
Flow Properties ◽  
Fine Powders

New Methods of Assessing Static and Dynamic Flow Characteristics of Textiles

2000 ◽  
Vol 70 (1) ◽  
pp. 53-58 ◽  
Author(s):  
Krzysztof Gniotek ◽  
Pawel Tokarski
Keyword(s):  
Flow Characteristics ◽  
Dynamic Flow ◽  
New Methods
Sign in / Sign up

Export Citation Format

Share Document