scholarly journals Modeling the snow surface temperature with a one-layer energy balance snowmelt model

2013 ◽  
Vol 10 (12) ◽  
pp. 15071-15118 ◽  
Author(s):  
J. You ◽  
D. G. Tarboton ◽  
C. H. Luce

Abstract. \\label{sec:abstract} Snow surface temperature is a key control on energy exchanges at the snow surface, particularly net longwave radiation and turbulent energy fluxes. The snow surface temperature is in turn controlled by the balance between various external fluxes and the conductive heat flux, internal to the snowpack. Because of the strong insulating properties of snow, thermal gradients in snow packs are large and nonlinear, a fact that has led many to advocate multiple layer snowmelt models over single layer models. In an effort to keep snowmelt modeling simple and parsimonious, the Utah Energy Balance (UEB) snowmelt model used only one layer but allowed the snow surface temperature to be different from the snow average temperature by using an equilibrium gradient parameterization based on the surface energy balance. Although this procedure was considered an improvement over the ordinary single layer snowmelt models, it still resulted in discrepancies between modeled and measured snowpack energy contents. In this paper we examine the parameterization of snow surface temperature in single layer snowmelt models from the perspective of heat conduction into a semi-infinite medium. We evaluate the equilibrium gradient approach, the force-restore approach, and a modified force-restore approach. In addition, we evaluate a scheme for representing the penetration of a refreezing front in cold periods following melt. We also introduce a method to adjust effective conductivity to account for the presence of ground near to a shallow snow surface. These parameterizations were tested against data from the Central Sierra Snow Laboratory, CA, Utah State University experimental farm, UT, and Subnivean snow laboratory at Niwot Ridge, CO. These tests compare modeled and measured snow surface temperature, snow energy content, snow water equivalent, and snowmelt outflow. We found that with these refinements the model is able to better represent the snowpack energy balance and internal energy content while still retaining a parsimonious one layer format.

2014 ◽  
Vol 18 (12) ◽  
pp. 5061-5076 ◽  
Author(s):  
J. You ◽  
D. G. Tarboton ◽  
C. H. Luce

Abstract. Snow surface temperature is a key control on and result of dynamically coupled energy exchanges at the snow surface. The snow surface temperature is the result of the balance between external forcing (incoming radiation) and energy exchanges above the surface that depend on surface temperature (outgoing longwave radiation and turbulent fluxes) and the transport of energy into the snow by conduction and meltwater influx. Because of the strong insulating properties of snow, thermal gradients in snow packs are large and nonlinear, a fact that has led many to advocate multiple layer snowmelt models over single layer models. In an effort to keep snowmelt modeling simple and parsimonious, the Utah Energy Balance (UEB) snowmelt model used only one layer but allowed the snow surface temperature to be different from the snow average temperature by using an equilibrium gradient parameterization based on the surface energy balance. Although this procedure was considered an improvement over the ordinary single layer snowmelt models, it still resulted in discrepancies between modeled and measured snowpack energy contents. In this paper we evaluate the equilibrium gradient approach, the force-restore approach, and a modified force-restore approach when they are integrated as part of a complete energy and mass balance snowmelt model. The force-restore and modified force-restore approaches have not been incorporated into the UEB in early versions, even though Luce and Tartoton have done work in calculating the energy components using these approaches. In addition, we evaluate a scheme for representing the penetration of a refreezing front in cold periods following melt. We introduce a method to adjust effective conductivity to account for the presence of ground near to a shallow snow surface. These parameterizations were tested against data from the Central Sierra Snow Laboratory, CA, Utah State University experimental farm, UT, and subnivean snow laboratory at Niwot Ridge, CO. These tests compare modeled and measured snow surface temperature, snow energy content, snow water equivalent, and snowmelt outflow. We found that with these refinements the model is able to better represent the snowpack energy balance and internal energy content while still retaining a parsimonious one layer format.


2009 ◽  
Vol 6 (3) ◽  
pp. 3863-3890 ◽  
Author(s):  
C. H. Luce ◽  
D. G. Tarboton

Abstract. The snow surface temperature is an important quantity in the snow energy balance, since it modulates the exchange of energy between the surface and the atmosphere as well as the conduction of energy into the snowpack. It is therefore important to correctly model snow surface temperatures in energy balance snowmelt models. This paper focuses on the relationship between snow surface temperature and conductive energy fluxed that drive the energy balance of a snowpack. Time series of snow temperature at the surface and through the snowpack were measured to examine energy conduction in a snowpack. Based on these measurements we calculated the snowpack energy content and conductive energy flux at the snow surface. We then used these estimates of conductive energy flux to evaluate formulae for the calculation of the conductive flux at the snow surface based on surface temperature time series. We use a method based on Fourier frequency analysis to estimate snow thermal properties. Among the formulae evaluated, we found that a modified force-restore formula, based on the superimposition of the force-restore equation capturing diurnal fluctuations on a gradually changing temperature gradient, had the best agreement with observations of heat conduction. This formula is suggested for the parameterization of snow surface temperature in a full snowpack energy balance model.


2010 ◽  
Vol 14 (3) ◽  
pp. 535-543 ◽  
Author(s):  
C. H. Luce ◽  
D. G. Tarboton

Abstract. The snow surface temperature is an important quantity in the snow energy balance, since it modulates the exchange of energy between the surface and the atmosphere as well as the conduction of energy into the snowpack. It is therefore important to correctly model snow surface temperatures in energy balance snowmelt models. This paper focuses on the relationship between snow surface temperature and conductive energy fluxes that drive the energy balance of a snowpack. Time series of snow temperature at the surface and through the snowpack were measured to examine energy conduction in a snowpack. Based on these measurements we calculated the snowpack energy content and conductive energy flux at the snow surface. We then used these estimates of conductive energy flux to evaluate formulae for the calculation of the conductive flux at the snow surface based on surface temperature time series. We use a method based on Fourier frequency analysis to estimate snow thermal properties. Among the formulae evaluated, we found that a modified force-restore formula, based on the superimposition of the force-restore equation capturing diurnal fluctuations on a gradually changing temperature gradient, had the best agreement with observations of heat conduction. This formula is suggested for the parameterization of snow surface temperature in a full snowpack energy balance model.


2014 ◽  
Vol 18 (9) ◽  
pp. 3553-3570 ◽  
Author(s):  
R. Sultana ◽  
K.-L. Hsu ◽  
J. Li ◽  
S. Sorooshian

Abstract. Noah (version 2.7.1), the community land-surface model (LSM) of National Centers for Environmental Predictions-National Center for Atmospheric Research (NCEP-NCAR), which is widely used to describe the land-surface processes either in stand-alone or in coupled land-atmospheric model systems, is recognized to underestimate snow–water equivalent (SWE). Noah's SWE bias can be attributed to its simple snow sub-model, which does not effectively describe the physical processes during snow accumulation and melt period. To improve SWE simulation in the Noah LSM, the Utah Energy Balance (UEB) snow model is implemented in Noah to test alternate snow surface temperature and snowmelt outflow schemes. Snow surface temperature was estimated using the force-restore method and snowmelt event is regulated by accounting for the internal energy of the snowpack. The modified Noah's SWE simulations are compared with the SWE observed at California's NRCS SNOTEL stations for 7 water years: 2002–2008, while the model's snow surface temperature is verified with observed surface-temperature data at an observation site in Utah. The experiments show that modification in Noah's snow process substantially reduced SWE estimation bias while keeping the simplicity of the Noah LSM. The results suggest that the model did not benefit from the alternate temperature representation but primary improvement can be attributed to the substituted snowmelt process.


Water ◽  
2020 ◽  
Vol 12 (8) ◽  
pp. 2284
Author(s):  
Achut Parajuli ◽  
Daniel F. Nadeau ◽  
François Anctil ◽  
Oliver S. Schilling ◽  
Sylvain Jutras

Temperature-index (TI) models are commonly used to simulate the volume and occurrence of meltwater in snow-fed catchments. TI models have varying levels of complexity but are all based on air temperature observations. The quality and availability of data that drive these models affect their predictive ability, particularly given that they are frequently applied in remote environments. This study investigates the performance of non-calibrated TI models in simulating the subcanopy snow water equivalent (SWE) of a small watershed located in Eastern Canada, for which some distinctive observations were collected. Among three relatively simple TI algorithms, the model that performed the best was selected based on the average percent bias (Pbias of 24%) and root mean square error (RMSE of 100 mm w.e.), and was designated as the base TI model. Then, a series of supplemental tests were conducted in order to quantify the performance gain that resulted from including the following inputs/processes to the base TI model: subcanopy incoming radiation, canopy interception, snow surface temperature, sublimation, and cold content. As a final test, all the above modifications were performed simultaneously. Our results reveal that, with the exception of snow sublimation (Pbias of 5.4%) and snow surface temperature, the variables mentioned above were unable to improve TI models within our sites. It is therefore worth exploring other feasible alternatives to existing TI models in complex forested environments.


1997 ◽  
Vol 36 (6) ◽  
pp. 818-824 ◽  
Author(s):  
Christian Plüss ◽  
Atsumu Ohmura

Abstract Longwave radiation in snow-covered alpine environments was investigated based on LOWTRAN7 calculations. The irradiance from the sky and from the surrounding topography were determined separately in order to detect the influence of the topography on longwave radiation balance. Sensitivity studies showed that the irradiance from the surrounding terrain is determined primarily by the atmospheric conditions within the investigated area and by the surface temperature of the surrounding terrain. In snow-covered environments, the air temperature is usually above the snow surface temperature and the effects of the air between the topography and the receiving surface may be relevant. Longwave irradiance from the surrounding terrain is an important component of the energy balance at the snow surface on inclined slopes and should be considered for areal investigations. A simple parameterization that accounts for the effects of the air is proposed for efficient calculation of longwave irradiance from snow-covered topography.


2001 ◽  
Vol 32 ◽  
pp. 217-222 ◽  
Author(s):  
Peter Höller

AbstractSnow surface temperature (Ts) plays an important role in the formation of surface hoar or near-surface faceted crystals The goal of this study was to obtain detailed information on Ts in different forest stands nelr the timberline. The investigations were conducted during clear nights and showed that the snow surface temperature is influenced very strongly by the forest canopy. While the air temperature was very similar on the different experimental sites, Ts was higher in the forest than in the open field; on the south-facing slope the difference between the forest and the open field was 3–4.5°C, and on the north-facing slope approximately 3–7°C. Taking into account that εair is 0.7 and εtree is 0.94, the incoming radiation (I ↓) for the different experimental sites was calculated by the equation of Brunt (the canopy density was estimated using photographs taken with an 8 mm fish-eye). To calculate Ts, air temperature and averaged values of the net radiation (because the net radiation (I) has only a small range of variation during clear nights) were used. The results show that the calculated values were higher than the measured values (by approximately 2°C). However, a better correlation was found by using lower values of the emissivity (εair0.67 and εtree0.91).


1998 ◽  
Vol 26 ◽  
pp. 22-26 ◽  
Author(s):  
Akihiro Hachikubo ◽  
Eizi Akitaya

Surface hoar growing for several clear and humid days were observed. During daytime, air and snow-surface temperature increased and relative humidity decreased, hence evaporation (sublimation) occurred at the snow surface. The amount of evaporation calculated using a bulk-transfer method suggests that the surface-hoar crystals which grew during the previous night should have disappeared but they were observed to survive on the snow surface even during the daytime. During the following night, new surface-hoar crystals formed on top of the older ones and grew even larger. This result indicates that, although the surface-hoar crystals evaporated into the air during the daytime, snow grains beneath the surface were warmed by solar radiation and evaporated to the air. They may partially condense into the surface-hoar crystals and make up for the reduction in size. Depth-hoar crystals formed beneath the snow surface for several days and the surface layer, composed of both types of hoar crystal, showed a very weak shear strength.


2017 ◽  
Vol 38 (16) ◽  
pp. 4722-4740 ◽  
Author(s):  
Carlos L. Pérez-Díaz ◽  
Tarendra Lakhankar ◽  
Peter Romanov ◽  
Jonathan Muñoz ◽  
Reza Khanbilvardi ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document