Modeling Joule Heating Effect on Thermal Efficiency of Photovoltaic Thermal (PVT) Collectors with Operation Mode Factor (OMF)

The purpose of the present study is developing the operation mode factor (OMF) by remodeling the thermal efficiency model of a hybrid PVT collector during steady state. Joule heating occurs when the photovoltaic (PV) panel operates at a high current during maximum power point tracking (MPPT) on higher irradiation. Under these conditions, some electrical energy converts to thermal energy within the PV cells. Joule heating contributed to increasing the PVT thermal efficiency. The steps were to construct the OMF by remodeling the thermal efficiency involving the Joule heating effect and to validate the results using the model by comparing the simulation and experiment. The dimensionless OMF was responsible for changes in thermal efficiency for PVT-mode. The conductive heat transfer coefficient from the surface to the absorber was the most decisive component in the OMF. Heat removal factor and OMF might be interrelated at the mass flow rate by decreasing PV temperature to maintain Joule heating. The proposed model with OMF had explained PVT-mode and T-mode with the RMS value of less than 1%. This model complemented the results of the previous studies. The results may contribute from the initial design to the operational monitoring for thermal to electrical energy production.

An integrated XFEM modeling with experimental measurements for optimizing thermal conductivity in carbon nanotube reinforced polyethylene

The present paper investigates the thermal properties of carbon nanotube reinforced polyethylene and specifically its potential as highly conductive material. To this end, an integrated approach is proposed combining both numerical and experimental procedures. First, in order to study conductive heat transfer in two-phase materials with imperfect interfaces, a detailed numerical model is developed based on the extended finite element method (XFEM), where material interfaces are modeled using the level set method. The thermal conductance at the interface of the carbon nanotubes and the polymer matrix is considered to be an unknown model parameter, the value of which is obtained by utilizing a series of experimental measurements of the composite material’s effective conductivity. The interfacial thermal conductance parameter value is inferred by calibrating the numerically predicted effective conductivity to the series of the corresponding experimental measurements. Once this parameter is estimated, the data-informed model is subsequently employed to provide reliable predictions of the effective conductivity of the composite for various weight fractions and configurations of carbon nanotubes in the parent material. Furthermore, microstructural morphologies that provide upper limits on the effective conductivity of the composite are identified via sensitivity analysis, demonstrating its potential as a highly conductive material.

Dating submarine landslides using the transient response of gas hydrate stability

Submarine landslides are prevalent on the modern-day seafloor, yet an elusive problem is constraining the timing of slope failure. Herein, we present a novel technique for constraining the age of submarine landslides without sediment core dating. Underneath a submarine landslide in the Orca Basin, Gulf of Mexico, in 3D seismic data we map an irregular bottom simulating reflection (BSR), which mimics the geometry of the pre-slide seafloor rather than the modern bathymetry. Based on the observed BSR, we suggest that the gas hydrate stability zone (GHSZ) is currently adjusting to the post-slide sediment temperature perturbations. We apply transient conductive heat flow modeling to constrain the response of the GHSZ to the slope failure, which yields a most likely age of ~8 ka demonstrating that gas hydrate systems can respond to slope failures even on the millennia timescales. We also provide an analytical approach to rapidly determine the age of submarine slides at any location.

Towards the Stable Evolution of Dendrites in the Case of Intense Convection in the Melt

The solid-phase pattern in the form of a dendrite is one of the frequently met structures produced from undercooled liquids. In the last decades, an analytical approach describing the steady-state crystal growth in the presence of conductive heat and mass transport has been constructed. However, experimental works show that crystal patterns frequently grow in the presence of convection. In this paper, a theoretical description based on convective heat and solute concentration transport near the solid/liquid phase interface is developed. The stable regime of crystallization in the presence of vigorous convection near the steady-state crystal vertex is studied. The stability analysis, determining the stable growth mode, and the undercooling balance law have been applied to deduce the stable values for the growth rate and tip diameter. Our analytical predictions (with convective transport) well describe experimental data for a small melt undercooling. Moreover, we compare both convective and conductive mechanisms in the vicinity of the crystal vertex. Our theory shows that convective fluxes substantially change the steady-state growth of crystals.

Refinement of the method for selecting the width of the conductor of printed circuit boards on a metal base, working in the absence of convection

The article proposes a refined method for calculating the width of the conductors of printed circuit boards on a metal base for the onboard devices of spacecraft, depending on the current flowing. The constructed refined mathematical model of the process of conductive heat exchange between the conductors and the metal base is described. The results of calculations of various, most common, locations of layers of printed circuit boards are presented. An analysis was carried out and a refined methodology was developed based on the results obtained. It allows you to easily (without complicate calculations) calculate the necessary values of the width of conductors. This technique is based on graphical methods, but allows you to perform technical calculations with sufficient accuracy. Accuracy is achieved by using special formulas that simplify the determination of the value of a physical quantity on a logarithmic scale. The disadvantages of the proposed method are indicated.

Plasma beta effects on the edge magnetic field structure and divertor heat-loads in Wendelstein 7-X high-performance scenarios

To support the scenario design for the upcoming longpulse high-performance campaign of Wendelstein 7-X, this work presents a study of high-beta full-field 3D equilibria obtained with the HINT code. For three magnetic configurations of different edge-iota, the effects of both overall pressure and pressure profile changes on the magnetic topology are analyzed. Anisotropic diffusion modeling is used to obtain estimates of the conductive heat load distribution both on the divertor and other plasma-facing components in finite-beta magnetic configurations. For the magnetic standard configuration, limitations of the model are outlined by comparing measured and predicted heatloads by performing a linear regression of the main strike-line position against various plasma parameters in both the experimental and the simulated device.

Thermal Performance of Cemented Paste Backfill Body Considering Its Slurry Sedimentary Characteristics in Underground Backfill Stopes

The combined mine backfill–geothermal (CMBG) system can be used to effectively extract geothermal energy by installing a heat exchange tube (HET) in the underground backfilled stopes of mines, which can be used as the heat supply for buildings in mines and the surrounding areas. The efficient performance of this system strongly depends on the thermal exchange process between the HET and its surrounding cemented paste backfill body (CPB). In this study, a validated simulation model is established to investigate the heat exchange performance of CPB, in which the nonuniformly distributed thermal properties in CPB are fully considered. The results indicate that the increase in the porosity has a negative effect on the heat exchange performance of CPB. With the increase in the porosity, the decreased rate of the conductive heat transfer in CPB could be up to approximately 18%. In conditions with seepage flow, the heat transfer capacity of CPB could be effectively improved. Generally, a higher hydraulic conductivity corresponds to a higher heat transfer performance of CPB. When the seepage velocity rose from 2 × 10−6 to 6 × 10−6 m/s, the thermal conductivity of CPB achieved a 114% increase from 1.843 to 3.957 W/(m·K). Furthermore, it was found that the thermal energy accumulates along the seepage flow direction, enhancing the thermal influencing radius of the HET in this direction. Thus, the arrangement of HETs should fully take into account the seepage flow effect. This proposed simulation model could provide a reference for parameter determination and optimization of CMBG systems.