scholarly journals Mechanical Characteristic and Water Absorption Property of Bio Composite from Sago Starch and Jute Fiber (Boehmeria Nivea) as the filler

2021 ◽  
Vol 2 (1) ◽  
pp. 94-99
Author(s):  
Rozanna Dewi ◽  
Oktaviani Oktaviani ◽  
Zainuddin Ginting ◽  
Novi Sylvia
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Absorption ◽  
Modulus Of Elasticity ◽  
High Water ◽  
Thermoplastic Starch ◽  
Absorption Capacity ◽  
Sago Starch ◽  
Hemp Fiber ◽  
Water Absorption Property

Environmentally friendly plastics can be degraded biologically in an anaerobic environment. This plastic is synthesized from starch such as sago starch which is available in abundance. In the form of bioplastics, its mechanical properties are still not compared to conventional plastics derived from crude oil, so its application is limited. The incorporation of filler material increases its mechanical properties, one of the selected fillers is hemp fiber as used in this study. Thermoplastic starch from sago with flax fiber as a filler and the addition of Polypropylene to improve mechanical properties with a certain composition to maintain its natural biodegradability. The mechanical properties analyzed were tensile strength, elongation and modulus of elasticity. Water absorption tests were also carried out to observe the water resistance properties. The results of the tensile strength test showed that the best tensile strength value of 9.32 Mpa was obtained at the addition of 35% fiber with a TPS: PP ratio of 1:1.5. The same conditions were obtained for the percent elongation with the results of 10.16% and the modulus of elasticity was 91.73 Mpa. Water absorption showed that 55% filler gave the lowest water     absorption, namely 4.41% at a ratio of TPS: PP 1:0.5. The addition of fiber filler into the bio-composite affects the tensile strength,    elongation and modulus of elasticity, the higher the volume of filler entering the bio-composite, the lower the value of tensile strength, elongation and modulus of elasticity, or vice versa. The ratio of addition of polypropylene matrix is also influential, the higher the ratio contributes to the tensile strength, elongation and higher modulus of elasticity. High water absorption capacity will reduce the performance of biocomposite, so the lower the water absorption ability, the better the quality of the biocomposite product and the wider its application

scholarly journals Influence of the surface treatment of tire rubber residues added in mortars

2008 ◽  
Vol 1 (2) ◽  
pp. 113-120 ◽  
Author(s):  
A. C. Marques ◽  
J. L. Akasaki ◽  
A. P. M. Trigo ◽  
M. L. Marques
Keyword(s):  
Mechanical Properties ◽  
Aqueous Solution ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Surface Treatment ◽  
Water Absorption ◽  
Modulus Of Elasticity ◽  
Tire Rubber ◽  
Flow Test ◽  
Made In

In this work it was evaluated the influence tire rubber addition in mortars in order to replace part of the sand (12% by volume). It was also intended to verify if the tire rubber treatment with NaOH saturated aqueous solution causes interference on the mechanical properties of the mixture. Compressive strength, splitting tensile strength, water absorption, modulus of elasticity, and flow test were made in specimens of 5cmx10cm and the tests were carried out to 7, 28, 56, 90, and 180 days. The results show reduction on mechanical properties values after addition of tire rubber and decrease of the workability. It was also observed that the tire rubber treatment does not cause any alteration on the results compared to the rubber without treatment.

scholarly journals Starch-Jute fiber hybrid biocomposite modified with Epoxy resin layer: Fabrication and Experimental Characterization

2018 ◽  
Author(s):  
Akarsh Verma ◽  
Kamal Joshi ◽  
Amit Gaur ◽  
V. K. Singh
Keyword(s):  
Tensile Strength ◽  
Water Absorption ◽  
Epoxy Resin ◽  
High Water ◽  
Epoxy Coating ◽  
Jute Fiber ◽  
Compression Moulding ◽  
Resin Layer ◽  
Major Disadvantage ◽  
Water Absorption Property

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

scholarly journals Evaluation of a biodegradable color concentrate in bags for coffee seedlings

DYNA ◽  
2020 ◽  
Vol 87 (212) ◽  
pp. 31-37
Author(s):  
Pedro Alban Bolaños ◽  
Amanda Parra Campos ◽  
Hector Samuel Villada Castillo ◽  
Hugo Portela Guarín ◽  
German Antonio Arboleda Muñoz ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Weight Gain ◽  
Carbon Black ◽  
Water Absorption ◽  
Modulus Of Elasticity ◽  
Significant Variation ◽  
Cassava Starch ◽  
Color Parameters ◽  
Influence Of Water

The aim of this study was to evaluate different formulations of a biodegradable black concentrate obtained from cassava starch and carbon black, on the mechanical properties, color, and water absorption of a film destined to the production of biodegradable bags for coffee seedlings. The modulus of elasticity, tensile strength and elongation properties is found to show significant variation due to the pigment, plasticizer, and lubricant concentration, both longitudinally and transversely of the film, the treatment being 40% pigment with the absence of plasticizer and lubricant for the pigment, which presented greater integrity in the mechanical properties evaluated in both directions. It is also noticeable that the different masterbatch formulations had an influence on the changes in the color parameters and weight gain of the film by the influence of water absorption.

scholarly journals Manufacture and Characterization of Biofoam Based On Composite of Taro Leaves Powder Reinforced Polyvinyl Acetate

2019 ◽  
pp. 141-148
Author(s):  
Arini Ulfah M.R ◽  
Syahrul Humaidi ◽  
Kurnia Sembiring
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Thermal Properties ◽  
Elastic Modulus ◽  
Water Absorption ◽  
Food Packaging ◽  
Raw Materials ◽  
Absorption Capacity ◽  
Third Stage ◽  
Leaf Powder

Biofoam material has been made for application of styrofoam substitute food packaging material from a mixture of raw materials: taro leaf powder and PVAc through a hot compaction method with variations of the composition of taro leaf powder: PVAc (80:20)% wt, (75:25)% wt, (70 : 30)% wt, (65:35) wt%, (60:40) wt%, (55:45)% wt, (50:50)% wt and (45:50)% wt. The first stage of taro leaves was blended and sifted with 100 mesh particle size. The second stage of the leaf powder of taro mixed with wet mixing was then mixed with PVAc as a matrix. The third stage of the homogeneous mixture was then put into the mold then compressed by heat to make it more dense with a pressure of 100 MPa and held for 10 minutes at 60 oC. Each biofoam sample that is ready to be characterized includes: physical properties (density, water absorption, functional groups and biodegredability), mechanical properties (tensile strength, elastic modulus, and elongation) and thermal properties (melting points). The characterization results showed that taro leaf powder: the optimum PVAc was (45: 55) wt% with a density value of 0.744 x 103 kg/m3, water absorption capacity of 1.765%, composed of OH and CH groups of PVAc and cellulose and C = C groups of lignin so that it has degrading properties of 91.2% for 50 days. Mechanical properties with tensile strength of 0.357 MPa, elastic modulus of 1.449 MPa, and elongation of 246.416%. Thermal properties with a melting point of 350.21 oC whose results have met the standards of conventional brand Synbra Technology. The results of biofoam material based on composite taro leaves and PVAc can be applied as food packaging.

scholarly journals Experimental Investigation of the Physical and Mechanical Properties of Sisal Fiber-Reinforced Concrete

Fibers ◽  
2018 ◽  
Vol 6 (3) ◽  
pp. 53 ◽  
Author(s):  
Abass Okeola ◽  
Silvester Abuodha ◽  
John Mwero
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Reinforced Concrete ◽  
Water Absorption ◽  
Modulus Of Elasticity ◽  
Physical And Mechanical Properties ◽  
Fiber Reinforced Concrete ◽  
Sisal Fiber ◽  
Fiber Reinforced ◽  
Split Tensile Strength

Concrete is a very popular material in the construction industry—it is, however, susceptible to quasi-brittle failure and restricted energy absorption after yielding. The incorporation of short discrete fibers has shown great promise in addressing these shortfalls. A natural fiber such as sisal is renewable, cheap, and easily available. It has also exhibited good tensile strength and can significantly improve the performance of concrete. In this study, the physical and mechanical properties of sisal fiber-reinforced concrete were reported. Sisal fibers were added in the mix at percentages of 0.5%, 1.0%, 1.5%, and 2.0% by weight of cement. Physical properties measured are workability, water absorption, and density while mechanical properties reported are compression strength, split tensile strength, and static modulus of elasticity. The computed modulus of elasticity of sisal fiber-reinforced concrete was compared with predicted values in some common design codes. From the study, it was concluded that sisal fiber can enhance the split tensile strength and Young’s modulus of concrete but cannot improve its workability, water absorption, and compressive strength.

Properties of Mortars Mixed with Polystyrene and Hemp Fiber Wastes

2021 ◽  
Author(s):  
Apised Suwansaard
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Tensile Strength ◽  
Compressive Strength ◽  
Water Absorption ◽  
Fiber Content ◽  
Partial Replacement ◽  
Hemp Fiber ◽  
Line Crack ◽  
Better Than

When polystyrene (PS) and hemp fiber waste were mixed into the sand aggregate, some physical-mechanical properties of mortar changed. The PS and hemp fiber were tested as partial replacements for sand in mortar with three designated percentages of 2.5, 5.0 and 10.0% by mass. The properties of mortar with PS were found to be better than that of the mortar with hemp fiber. The water absorption of mortar with PS was comparable with the reference mortar but lower than that of mortar with hemp fiber. The compressive strength of the mortar with PS was higher than that with hemp fiber whereas the tensile strength of the mortar with 2.5% PS and hemp fiber was comparable and was higher than that of the reference mortar. The thermal conductivity of a wall plastered by mortar containing PS decreased as the PS content was increased, whereas the thermal conductivity of a wall plastered by mortar containing hemp fiber increased as the hemp fiber content was increased. Thick crack was detected in the reference wall while hair line crack occurred from the wall plastered with PS and hemp fiber mortars. The results indicated that 10.0% PS could be used as a partial replacement for sand in mortar with an improvement in some of the properties of the mortar.

scholarly journals PENGARUH PENAMBAHAN BENTONIT TERMODIFIKASI SEBAGAI PENGISI TERHADAP SIFAT MEKANIK DAN PENYERAPAN AIR KOMPOSIT EPOKSI

2017 ◽  
Vol 5 (4) ◽  
pp. 39-44
Author(s):  
Alvian ◽  
Kenrick ◽  
Iriany
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Absorption ◽  
Epoxy Resin ◽  
Cetyltrimethylammonium Bromide ◽  
Absorption Capacity ◽  
Modified Bentonite ◽  
Maximum Value ◽  
Ftir Characterization ◽  
Scaning Electron Microscopy

Research about the application of modified bentonite as filler in epoxy has been done for the purpose of getting the best composition of modified bentonite as filler at epoxy composite to obtain the best mechanical properties such as tensile strength, impact strength and the water absorption. In this research, epoxy resin mixed with bentonite which have been modified using cetyltrimethylammonium bromide (CTAB) surfactant with various concentrations of 0,05M, 0,1M, and 0,15M. Modified bentonite filler and TiO2 then mixed with epoxy resin with various concentration of 5%, 10%, 15%, and 20% of filler from the total mass of the composite and then the composite was produced with hand lay-up method. The result of FTIR characterization showed that the bond between matrix and the filler produced was only interfacial bonding. The result of the mechanical properties test indicated that 5% of filler composition with 0,1M of surfactant concentration obtained the maximum value of tensile strength and mechanical strength respectively 33,667 MPa and 12564,9 J/m2. The result of mechanical properties test was supported by analysis of Scaning Electron Microscopy (SEM). On the test of water absorption, the water absorption capacity increased along with the increased of filler composition.

Mechanical Properties and Resistance to Water Ingress of Cement Concrete Made with Non-Cyclic Alkanes

2014 ◽  
Vol 1054 ◽  
pp. 58-63 ◽  
Author(s):  
Roman Jaskulski ◽  
Wojciech Kubissa
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Water Absorption ◽  
Absorption Capacity ◽  
Paraffin Wax ◽  
Water Absorption Capacity ◽  
Cement Concrete ◽  
Water Ingress ◽  
Capacity Reduction ◽  
Cyclic Alkanes

The goal of presented research is an assessment of fundamental mechanical properties and resistance to water ingress of concrete with non-cyclic alkanes. Compressive and tensile strength, water absorption capacity and sorptivity of concrete made with and without an admixture of non-cyclic alkanes has been analysed. The paraffin enriched concretes have been made with 1% (C1F and C1C) and 3% (C3F and C3C) volume addition of paraffin wax. The paraffin wax has been used in two grades of comminution: fine (FP) in CxF concretes and coarse (CP) in CxC concretes. A significant (35%) loss of compressive strength of concretes with admixtures has been noticed and no loss in tensile strength was observed. Up to 25% of water absorption capacity reduction and irrefutable (8 times) sorptivity reduction has been also noticed, but only in the case of concrete made with admixture of FP.

scholarly journals Effects of Different Types of Fibers on the Physical and Mechanical Properties of MICP-Treated Calcareous Sand

Materials ◽  
2021 ◽  
Vol 14 (2) ◽  
pp. 268
Author(s):  
Jitong Zhao ◽  
Huawei Tong ◽  
Yi Shan ◽  
Jie Yuan ◽  
Qiuwang Peng ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Water Absorption ◽  
Glass Fiber ◽  
Physical And Mechanical Properties ◽  
Polyester Fiber ◽  
Engineering Properties ◽  
Fiber Types ◽  
Calcite Precipitation ◽  
Calcareous Sand ◽  
Hemp Fiber

Microbial-induced calcite precipitation (MICP) has been a promising method to improve geotechnical engineering properties through the precipitation of calcium carbonate (CaCO3) on the contact and surface of soil particles in recent years. In the present experiment, water absorption and unconfined compressive strength (UCS) tests were carried out to investigate the effects of three different fiber types (glass fiber, polyester fiber, and hemp fiber) on the physical and mechanical properties of MICP-treated calcareous sand. The fibers used were at 0%, 0.10%, 0.15%, 0.20%, 0.25%, 0.30%, 0.35%, and 0.40% relative to the weight of the sand. The results showed that the failure strain and ductility of the samples could be improved by adding fibers. Compared to biocemented sand (BS), the water absorption of these three fiber-reinforced biocemented sands were, respectively, decreased by 11.60%, 21.18%, and 7.29%. UCS was, respectively, increased by 24.20%, 60.76%, and 6.40%. Polyester fiber produced the best effect, followed by glass fiber and hemp fiber. The optimum contents of glass fiber and polyester fiber were 0.20% and 0.25%, respectively. The optimum content of hemp fiber was within the range of 0.20–0.25%. Light-emitting diode (LED) microscope and scanning electron microscope (SEM) images lead to the conclusion that only a little calcite precipitation had occurred around the hemp fiber, leading to a poor bonding effect compared to the glass and polyester fibers. It was therefore suggested that polyester fiber should be used to improve the properties of biocemented sand.

scholarly journals Cellulose Nanofibrils/Xyloglucan Bio-Based Aerogels with Shape Recovery

Gels ◽  
2021 ◽  
Vol 7 (1) ◽  
pp. 5
Author(s):  
Samuel Mandin ◽  
Samuel Moreau ◽  
Malika Talantikite ◽  
Bruno Novalès ◽  
Jean-Eudes Maigret ◽  
...  
Keyword(s):  
Water Absorption ◽  
Shape Recovery ◽  
Cellulose Nanofibrils ◽  
High Water ◽  
Absorption Capacity ◽  
Absorption Properties ◽  
High Affinity ◽  
High Water Absorption ◽  
Freezing Procedure ◽  
The Impact

Bio-based aerogels containing cellulose nanofibrils (CNFs) are promising materials due to the inherent physical properties of CNF. The high affinity of cellulose to plant hemicelluloses (xyloglucan, xylan, pectin) is also an opportunity to develop biomaterials with new properties. Here, we prepared aerogels from gelled dispersions of CNFs and xyloglucan (XG) at different ratios by using a freeze-casting procedure in unidirectional (UD) and non-directional (ND) manners. As showed by rheology analysis, CNF and CNF/XG dispersions behave as true gels. We investigated the impact of the freezing procedure and the gel’s composition on the microstructure and the water absorption properties. The introduction of XG greatly affects the microstructure of the aerogel from lamellar to cellular morphology. Bio-based aerogels showed high water absorption capacity with shape recovery after compression. The relation between morphology and aerogel compositions is discussed.

Sign in / Sign up

Export Citation Format

Share Document