scholarly journals Performance Evaluation of a Low-Grade Low-Heat-Rejection Diesel Engine with Crude Pongamia oil

2012 ◽  
Vol 2012 ◽  
pp. 1-10 ◽  
Author(s):  
Ch. Kesava Reddy ◽  
M. V. S. Murali Krishna ◽  
P. V. K. Murthy ◽  
T. Ratna Reddy
Keyword(s):  
Diesel Engine ◽  
Cylinder Head ◽  
Peak Load ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Injection Timing ◽  
Low Grade ◽  
Heat Rejection ◽  
Pongamia Oil ◽  
Diesel Operation

Investigations are carried out to evaluate the performance of a low heat rejection (LHR) diesel engine with ceramic coated cylinder head [ceramic coating of thickness 500 microns is done on inside portion of cylinder head] with different operating conditions [normal temperature and pre-heated temperature] of crude Pongamia oil (CPO) with varied injection pressure and injection timing. Performance parameters and pollution levels are determined at various magnitudes of brake mean effective pressure. Combustion characteristics at peak load operation of the engine are measured with special pressure-crank angle software package. Conventional engine (CE) showed deteriorated performance, while LHR engine showed improved performance with CPO operation at recommended injection timing and pressure and the performance of both version of the engine is improved with advanced injection timing and at higher injection pressure when compared with CE with pure diesel operation. The optimum injection timing is 31°bTDC for conventional engine while it is 29°bTDC with LHR engine with vegetable oil operation. Peak brake thermal efficiency increased by 5%, smoke levels decreased by 2% and NOx levels increased by 40% with CPO operation on LHR engine at its optimum injection timing, when compared with pure diesel operation on CE at manufacturer’s recommended injection timing.

Investigations on Low Heat Rejection Diesel Engine With Crude Jatropha Oil as an Alternate Fuel

2002 ◽  
Author(s):  
M. V. S. Murali Krishna ◽  
C. M. Vara Prasad ◽  
Tandur Rajashekar ◽  
Supriya Tiwari ◽  
T. Sujani
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Injection Pressure ◽  
High Viscosity ◽  
Injection Timing ◽  
Jatropha Oil ◽  
Heat Rejection ◽  
Reduction Of Nox ◽  
Conventional Diesel Fuel ◽  
Diesel Operation

Jatropha oil, a non-edible vegetable oil shows a greater potential for replacing conventional diesel fuel quite effectively, as its properties are compatible to that of diesel fuel. But low volatility and high viscosity of jatropha oil call for hot combustion chamber, which is provided by a low heat rejection diesel engine with threaded air gap piston and liner with superni-90 inserts. The performance of the engine with jatropha oil is obtained with different versions of the engine such as conventional engine and insulated engine at normal and preheat condition of the oil, with varying injection pressure and timing and compared to the engine with pure diesel operation at recommended injection pressure and timing. Increase of thermal efficiency of 18% and reduction of NOx levels by 5% are observed at optimized injection timing and at higher injection pressure with insulated engine at preheat condition of jatropha oil in comparison with pure diesel operation on conventional engine.

Performance Evaluation of a Low Heat Rejection Diesel Engine with Jatropha Oil

2013 ◽  
Vol 11 ◽  
pp. 27-44 ◽  
Author(s):  
N. Janardhan ◽  
M.V.S. Murali Krishna ◽  
P. Ushasri ◽  
P.V.K. Murthy
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Peak Pressure ◽  
Air Gap ◽  
Injection Timing ◽  
Jatropha Oil ◽  
Opening Pressure ◽  
Brake Thermal Efficiency ◽  
Heat Rejection ◽  
Diesel Operation

Investigations were carried out to evaluate the performance of a low heat rejection (LHR) diesel engine consisting of air gap insulated piston with 3-mm air gap, with superni (an alloy of nickel) crown, air gap insulated liner with superni insert and ceramic coated cylinder head with different operating conditions of crude jatropha oil (CJO) with varied injection timing and injector opening pressure . Performance parameters [brake thermal efficiency, exhaust gas temperature, coolant load and volumetric efficienc and exhaust emissions [smoke and oxides of nitroge were determined at various values of brake mean effective pressure (BMEP). Combustion characteristics [ peak pressure, time of occurrence of peak pressure and maximum rate of pressure ris of the engine were at peak load operation of the engine. Conventional engine (CE) showed deteriorated performance, while LHR engine showed improved performance with vegetable operation at recommended injection timing and pressure. The performance of both versions of the engine improved with advanced injection timing and higher injector opening pressure when compared with CE with pure diesel operation. Relatively, peak brake thermal efficiency increased by 14%, smoke levels decreased by 27% and NOx levels increased by 49% with vegetable oil operation on LHR engine at its optimum injection timing, when compared with pure diesel operation on CE at manufacturers recommended injection timing.

Potential of a Medium Grade Low Heat Rejection Diesel Engine With Crude Tobacco Seed Oil

2013 ◽  
Author(s):  
M. V. S. Murali Krishna ◽  
P. Pavan Kumar ◽  
P. V. K. Murthy ◽  
D. Baswaraju
Keyword(s):  
Diesel Engine ◽  
Maximum Rate ◽  
Seed Oil ◽  
Peak Pressure ◽  
Injection Pressure ◽  
Air Gap ◽  
Injection Timing ◽  
Brake Thermal Efficiency ◽  
Tobacco Seed ◽  
Diesel Operation

Investigations were carried out to evaluate the performance of a medium grade low heat rejection (LHR) diesel engine consisting of air gap insulated piston with 3-mm air gap, with superni (an alloy of nickel) crown and air gap insulated liner with superni insert with different operating conditions of crude tobacco seed oil with varied injection timing and injection pressure. Performance parameters of brake thermal efficiency (BTE), exhaust gas temperature (EGT), volumetric efficiency (VE), coolant load (CL) and sound intensity were determined at various values of brake mean effective pressure (BMEP) of the engine. Exhaust emissions of smoke and oxides of nitrogen (NOx) were noted at different values of BMEP of the engine. Combustion characteristics of peak pressure (PP), time of occurrence of peak pressure (TOPP), maximum rate of pressure rise (MRPR) and time of occurrence of maximum rate of pressure (TOMRPR) were measured with TDC (top dead centre) encoder, pressure transducer, console and special pressure-crank angle software-package at the peak load operation of the engine. Conventional engine (CE) showed deteriorated performance, while LHR engine showed improved performance with crude tobacco seed oil (CTSO) operation when compared with pure diesel operation at recommended injection timing and pressure. The optimum injection timing was found to be 32°bTDC (before top dead centre) with CE while it was 30°bTDC with LHR engine with vegetable oil operation. The performance of both version of the engine improved with advanced injection timing and higher injection pressure with test fuels. Peak brake thermal efficiency increased by 4%, volumetric efficiency decreased by 8%, smoke levels decreased by 4% and NOx levels increased by 37% with vegetable oil operation on LHR engine at its optimum injection timing, when compared with pure diesel operation on CE at manufacturer’s recommended injection timing of 27°bTDC.

Experimental Investigations on DI Diesel Engine With Low Heat Rejection Combustion Chamber With Waste Fried Vegetable Oil and its Biodiesel

2015 ◽  
Author(s):  
Raavi Peraiah Chowdary ◽  
Maddali V. S. Murali Krishna ◽  
T. Kishen Kumar Reddy ◽  
D. Srikanth ◽  
P. V. Krishna Murthy ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Vegetable Oil ◽  
Alternative Fuels ◽  
Air Gap ◽  
Operating Conditions ◽  
Injection Timing ◽  
Heat Rejection ◽  
Improved Performance ◽  
Ci Engines

Biodiesels derived from vegetable oils present a very promising alternative fuels for diesel fuel, since they have numerous advantages compared to fossil fuels. However crude vegetable oil and biodiesel have high viscosity and low volatility causing combustion problems in CI engines, call for engine with hot combustion chamber. Investigations were carried out on single–cylinder, four–stroke, water cooled, 3.68 kW direct injection diesel engine at a speed of 1500 rpm to evaluate the performance of a engine with low heat rejection (LHR) combustion chamber. It consisted of an air gap (3 mm) insulated piston with superni (an alloy of nickel) crown and an air gap (3 mm) insulated liner with superni insert and ceramic coated cylinder head fuelled with different operating conditions (normal temperature and preheated temperature) of waste fried vegetable oil and its biodiesel with varied injection timing and injector opening pressure. Engine with LHR combustion chamber with biodiesel showed improved performance over conventional engine (CE) at 27° bTDC and at optimum injection timing. Biodiesel showed improved performance over crude vegetable oil with engine with both versions of the combustion chamber. Preheated test fuels and increase of injection pressure showed reduction of pollution levels and marginally improved performance over normal test fuels.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Investigations on performance of diesel engine by varying injection timings with design modification on piston crown

2018 ◽  
Vol 15 (5) ◽  
pp. 562-566
Author(s):  
Vijaya K. ◽  
Shailesh Palaparty ◽  
Raghavan Srinivasa ◽  
Ravi Kumar Puli
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Combustible Mixture ◽  
Injection Timing ◽  
Connecting Rod ◽  
Design Modification ◽  
Content Type ◽  
Piston Head ◽  
Piston Crown ◽  
Fuel Vaporization

Purpose Investigations are carried out with the aim of improving performance of a diesel engine with the design modification on piston crown to stimulate the uniform combustion by inducing turbulence in the incoming charge. Design/methodology/approach A stirrer is introduced at the top of the piston so as to inculcate more turbulence to the incoming charge by improving the rate of fuel vaporization. Whirling motion is created in the combustible mixture by providing rotating blades on the cavity/bowl of the reciprocating piston head. By putting a simple link mechanism, the oscillatory motion of connecting rod will rotate the blade by an angle of 60°. Findings The investigations are carried out with and without swirl piston at 17.5 compression ratio and 200 bar injection pressure by varying injection timings. Originality/value Finally, the result shows that by using the modified piston, nearly 3 per cent of efficiency increased and 31 per cent of NOx emissions are reduced compared to that of a normal piston with 80 per cent load at standard injection timing.

Characterization of the Nonroad Modified Diesel Engine Using a Novel Entropy-VIKOR Approach: Experimental Investigation and Numerical Simulation

2019 ◽  
Vol 141 (8) ◽  
Author(s):  
Pushpendra Kumar Sharma ◽  
Dilip Sharma ◽  
Shyam Lal Soni ◽  
Amit Jhalani
Keyword(s):  
Numerical Simulation ◽  
Diesel Engine ◽  
Engine Performance ◽  
Injection Pressure ◽  
Multicriteria Decision Making ◽  
Operating Parameters ◽  
Injection Timing ◽  
Oxides Of Nitrogen ◽  
Compression Ignition Engine ◽  
Continuous Increase

Excessive use of diesel engines and continuous increase in environmental pollution has drawn the attention of researchers in the area of the compression ignition engine. In this research article, an innovative investigation of the nonroad modified diesel engine is reported with the effective use of the hybrid Entropy-VIKOR approach. Hence, it becomes necessary to prioritize and optimize the performance defining criteria, which provides higher BTE along with lower emission simultaneously. The engine load, injection timing (Inj Tim), injection pressure (Inj Pre), and compression ratio (Com R) were selected as engine operating parameters for experimentation at the constant speed of 1500 rpm engine. The effect on engine performance parameters (BTE and BSEC) and emission (carbon monoxide (CO), total oxide of carbon (TOC), oxides of nitrogen (NOx), hydrocarbon (HC), and smoke) was studied experimentally. The optimum results were observed at load 10.32 kg, Inj Tim 20 deg btdc, Inj Pre 210 bar, and Com R 21:1 at which highest BTE of 22.24% and lowest BSEC of 16,188.5 kJ/kWh were obtained. Hybrid entropy-VIKOR approach was applied to establish the optimum ranking of the nonroad modified diesel engine. The experimental results and numerical simulation show that optimizing the engine operating parameters using the entropy-VIKOR multicriteria decision-making (MCDM) technique is applicable.

An Experimental Study on Smoke Reduction Effect of Post Injection in Combination With Pilot Injection for a Diesel Engine

2013 ◽  
Vol 136 (4) ◽  
Author(s):  
Long Liu ◽  
Naoto Horibe ◽  
Tatsuya Komizo ◽  
Issei Tamura ◽  
Takuji Ishiyama
Keyword(s):  
Diesel Engine ◽  
Injection Pressure ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pilot Injection ◽  
Post Injection ◽  
Spray Flames ◽  
Injection Quantity ◽  
Main Injection ◽  
Reduction Effect

With the universal utilization of the common-rail injection system in automotive diesel engines, the multistage injection strategies have become typical approaches to satisfy the increasingly stringent emission regulations, and especially the post injection has received considerable attention as an effective way for reducing the smoke emissions. Normally the post injection is applied in combination with the pilot injection to restrain the NOx emissions, smoke emissions, and combustion noise simultaneously, and the pilot injection condition affects the combustion process of the main injection and might affect the smoke reduction effect of the post injection. Thus this study aims at obtaining the post injection strategy to reduce smoke emissions in a diesel engine, where post injection is employed in combination with pilot injection. The experiments were performed using a single-cylinder diesel engine under various conditions of pilot and post injection with a constant load at an IMEP of 1.01 MPa, fixed speed of 1500 rpm, and NOx emissions concentration of 150 ± 5 ppm that was maintained by adjusting the EGR ratio. The injection pressure was set at 90 MPa at first, and then it was varied to 125 MPa to evaluate the effects of post injection on the smoke reduction in the case of higher injection pressure. The experimental results show that small post injection quantity with a short interval from the end of main injection causes less smoke emissions. And larger pilot injection quantity and later pilot injection timing lead to higher smoke emissions. And then, to explore and interpret the smoke emissions tendencies with varying pilot and post injection conditions, the experimental results of three-stage injection conditions were compared to those of two reference cases, which only included the pilot and main injection, and the interaction between main spray flames and post sprays was applied for analysis. Based on the comparative analysis, the larger smoke reduction effect of post injection was observed with the larger pilot injection quantity, while it is not greatly influenced by pilot injection timing. In addition, the smoke emissions can be reduced considerably by increasing the injection pressure, however the smoke reduction effect of post injection was attenuated. And all of these tendencies were able to be interpreted by considering the intensity variation of the interaction between main spray flames and post sprays.

Progress on the Investigation of Coal-Water Slurry Fuel Combustion in a Medium-Speed Diesel Engine: Part 5—Combustion Studies

1992 ◽  
Vol 114 (3) ◽  
pp. 515-521 ◽  
Author(s):  
B. D. Hsu ◽  
G. L. Confer ◽  
Z. J. Shen
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Combustion Efficiency ◽  
Fuel Combustion ◽  
Injection Timing ◽  
Water Slurry ◽  
Medium Speed ◽  
Engine Part ◽  
Coal Water Slurry

In the GE 7FDL single-cylinder research diesel engine, coal-water slurry (CWS) fuel combustion optimization studies were conducted using electronically controlled CWS and pilot accumulator injectors. The most important performance parameters of peak firing pressure, combustion efficiency (coal burnout), and specific fuel comsumption were evaluated in relationship to CWS and pilot injection timing, CWS injector hole size, shape, and number, CWS fuel injection spray angles and injection pressure. Heat release diagrams, as well as exhaust samples (gaseous and particulate), were analyzed for each case. Interesting effects of fuel spray impingement and CWS fuel “Delayed Ignition” were observed. With the engine operating at 2.0 MPa IMEP and 1050 rpm, it was able to obtain over 99.5 percent combustion efficiency while holding the cylinder firing pressure below 17 MPa and thermal efficiency equivalent to diesel fuel operation.

Effect of High Pressure Post Injection on Soot and NO Trade-Off in a DI Diesel Engine

2010 ◽  
Author(s):  
Kamran Poorghasemi ◽  
Fathollah Ommi ◽  
Vahid Esfahanian
Keyword(s):  
Diesel Engine ◽  
Soot Formation ◽  
Three Dimensional ◽  
Injection Pressure ◽  
Combustion Mechanism ◽  
Injection Timing ◽  
Post Injection ◽  
Multiple Injection ◽  
Trade Off ◽  
Di Diesel Engine

In DI Diesel engines NO and Soot trade off is an important challenge for Engineers. In this paper, at first, multiple injection strategy will be introduced as a useful way to reduce both NO and Soot emissions simultaneously. Then the effect of injection pressure in post injection on the engine emissions will be studied. Investigations have been conducted on DI diesel engine. To evaluate the benefits of multiple injection strategies and to reveal combustion mechanism, modified three dimensional CFD code KIVA-3V was used. Results showed that using post injection with appropriate dwell between injection pulses can be effective in simultaneously reduction of emissions. Based on computation results, NO reduction formation mechanism is a single injection with retarded injection timing. It is shown that reduced soot formation is because of the fact that the soot producing rich regions at the fuel spray head are not replenished by new fuel when the injection is stopped and then restarted. Also increasing injection pressure in post injection will reduce the Soot emission dramatically while NO is in control and it is due to increasing fuel burning rate in post injection pulse.

Sign in / Sign up

Export Citation Format

Share Document