Influence of housing system on the physical, morphological, and mechanical properties of Japanese quail eggs

The mechanical properties of three titanium alloys (Ti-7Mo-3Al, Ti-7Mo- 3Cu and Ti-7Mo-3Ta) were evaluated as function of: 1) Solutionizing in the beta field and aging, 2) Thermal Mechanical Processing in the beta field and aging, 3) Solutionizing in the alpha + beta field and aging. The samples were isothermally aged in the temperature range 300° to 700*C for 4 to 24 hours, followed by a water quench. Transmission electron microscopy and X-ray method were used to identify the phase formed. All three alloys solutionized at 1050°C (beta field) transformed to martensitic alpha (alpha prime) upon being water quenched. Despite this heavily strained alpha prime, which is characterized by microtwins the tensile strength of the as-quenched alloys is relatively low and the elongation is as high as 30%.

Download Full-text

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100074896 ◽

1983 ◽

Vol 41 ◽

pp. 220-221

Author(s):

L.J. Chen ◽

H.C. Cheng ◽

J.R. Gong ◽

J.G. Yang

Keyword(s):

Mechanical Properties ◽

Cooling Rate ◽

Automobile Industry ◽

High Strength ◽

Weight Percent ◽

Low Alloy Steels ◽

Dual Phase ◽

Resource Requirement ◽

Alloy Steels ◽

Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Download Full-text

Lattice Imaging of Grain Boundaries in Ceramics

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100078171 ◽

1977 ◽

Vol 35 ◽

pp. 114-115

Author(s):

D. R. Clarke ◽

G. Thomas

Keyword(s):

Mechanical Properties ◽

High Temperature ◽

Silicon Nitride ◽

Grain Boundaries ◽

High Temperature Strength ◽

Current Interest ◽

Lattice Imaging ◽

Special Significance ◽

Structural Applications ◽

Refractory Ceramics

Grain boundaries have long held a special significance to ceramicists. In part, this has been because it has been impossible until now to actually observe the boundaries themselves. Just as important, however, is the fact that the grain boundaries and their environs have a determing influence on both the mechanisms by which powder compaction occurs during fabrication, and on the overall mechanical properties of the material. One area where the grain boundary plays a particularly important role is in the high temperature strength of hot-pressed ceramics. This is a subject of current interest as extensive efforts are being made to develop ceramics, such as silicon nitride alloys, for high temperature structural applications. In this presentation we describe how the techniques of lattice fringe imaging have made it possible to study the grain boundaries in a number of refractory ceramics, and illustrate some of the findings.

Download Full-text

Electron Microscopic Observation of the Longitudinal Organization of Poly (p-Phenylene Terephthalamide) Fibers

Proceedings, annual meeting, Electron Microscopy Society of America ◽

10.1017/s0424820100055734 ◽

1982 ◽

Vol 40 ◽

pp. 680-681

Author(s):

Li Li-Sheng ◽

L.F. Allard ◽

W.C. Bigelow

Keyword(s):

Electron Microscopy ◽

Mechanical Properties ◽

Scanning Electron Microscopy ◽

Microscopic Observation ◽

Electron Microscopic Observation ◽

Electron Microscopic ◽

Aromatic Polyamides ◽

Radial Arrangement ◽

Scanning Electron ◽

Better Than

The aromatic polyamides form a class of fibers having mechanical properties which are much better than those of aliphatic polyamides. Currently, the accepted morphology of these fibers as proposed by M.G. Dobb, et al. is a radial arrangement of pleated sheets, with the plane of the pleats parallel to the axis of the fiber. We have recently obtained evidence which supports a different morphology of this type of fiber, using ultramicrotomy and ion-thinning techniques to prepare specimens for transmission and scanning electron microscopy.

Download Full-text