scholarly journals Influence of tensile softening of concrete on crack development and failure in concrete and reinforced concrete beams

2019 ◽  
Vol 68 (1) ◽  
pp. 213-223 ◽  
Author(s):  
Marta Słowik
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Load Capacity ◽  
Plain Concrete ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Concrete Members ◽  
Cracking Process ◽  
Tensile Softening

In the paper, the own test results were presented. The experimental investigation was focused at determining the cracking and load capacity of beams made of concrete. The beams were characterized by different longitudinal reinforcement ratio from zero — plain concrete beams, through low ratio 0.12% — slightly reinforced concrete beams, middle ratio 0.9% — typical reinforced concrete beams, up to the ratios 1.3% and 1.8% — higher reinforced concrete beams. On the basis of the performed experiments and the results of numerical calculations, the process of crack’s formation and crack’s development in plain concrete, slightly reinforced concrete and reinforced concrete beams with different reinforcement ratio was described. When discussing cracking process in the beams, the contribution of strain softening of tensile concrete in the microcracked zone on the character of beams’ failure was analysed as well. Keywords: civil engineering, concrete and reinforced concrete members, cracking and load capacity.

scholarly journals The analysis of load carrying capacity and cracking of slightly reinforced concrete members in bending

2008 ◽  
Vol 2 (1) ◽  
pp. 065-078
Author(s):  
Marta Słowik
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Test Results ◽  
Concrete Members ◽  
Load Carrying

Slightly reinforced concrete members are the members made by concrete with reinforcement less than minimum given in codes for reinforced concrete ones. Plain concrete and slightly reinforced concrete members in bending are treated in the same way during the dimensioning and the influence of longitudinal reinforcement on the load carrying capacity is not taken into account. The mechanism of work and crack formation in slightly reinforced concrete members is not completely recognized. The author’s own research program was made. The experiment was aimed at the determination of cracking moment and load carrying capacity of slightly reinforced concrete beams with different reinforcement ratio. Also plain concrete beams and the typical reinforced concrete beam were tested. The analysis of the obtained values of maximum bending moment and crack’s widths was made according to the reinforcement ratio. The analysis of test results shows how the presence of longitudinal steel bars in concrete members, even when reinforcement ratio is low, changes cracking process and influences the value of cracking moment in flexural members. On the basis of test results, the method how to calculate the load carrying capacity of slightly reinforced concrete elements in bending has been proposed.

scholarly journals Numerical Sensing of Plastic Hinge Regions in Concrete Beams with Hybrid (FRP and Steel) Bars

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3255 ◽  
Author(s):  
Fang Yuan ◽  
Mengcheng Chen
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Plastic Hinge ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Concrete Members ◽  
Steel Bars ◽  
Hybrid Reinforcement ◽  
Steel Hardening

Fibre-reinforced polymer (FRP)-reinforced concrete members exhibit low ductility due to the linear-elastic behaviour of FRP materials. Concrete members reinforced by hybrid FRP–steel bars can improve strength and ductility simultaneously. In this study, the plastic hinge problem of hybrid FRP–steel reinforced concrete beams was numerically assessed through finite element analysis (FEA). Firstly, a finite element model was proposed to validate the numerical method by comparing the simulation results with the test results. Then, three plastic hinge regions—the rebar yielding zone, concrete crushing zone, and curvature localisation zone—of the hybrid reinforced concrete beams were analysed in detail. Finally, the effects of the main parameters, including the beam aspect ratio, concrete grade, steel yield strength, steel reinforcement ratio, steel hardening modulus, and FRP elastic modulus on the lengths of the three plastic zones, were systematically evaluated through parametric studies. It is determined that the hybrid reinforcement ratio exerts a significant effect on the plastic hinge lengths. The larger the hybrid reinforcement ratio, the larger is the extent of the rebar yielding zone and curvature localisation zone. It is also determined that the beam aspect ratio, concrete compressive strength, and steel hardening ratio exert significant positive effects on the length of the rebar yielding zone.

Cracking behaviour of concrete beams reinforced with fiber reinforced plastic rebars

1996 ◽  
Vol 23 (6) ◽  
pp. 1172-1179 ◽  
Author(s):  
R. Masmoudi ◽  
B. Benmokrane ◽  
O. Chaallal
Keyword(s):  
Reinforced Concrete ◽  
Crack Width ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Test Results ◽  
Fiber Reinforced ◽  
Fiber Reinforced Plastic ◽  
Concrete Members ◽  
Reinforced Plastic ◽  
Cracking Pattern

This paper presents the results of an experimental investigation on the cracking behaviour of concrete beams reinforced with fiber reinforced plastic rebars. The effects of reinforcement ratio on the cracking pattern, crack spacing, cracking moment, and crack width are investigated. The test results indicate that the reinforcement ratio has no meaningful effect on the cracking moment, which can be calculated as recommended by the ACI code. Also, the use of the equations adopted by ACI and the European codes for the prediction of crack width of conventionally reinforced concrete members is investigated and due modifications are made. Both relationships show good correlation with the test results; and the prediction of crack width of concrete beams reinforced with these two types of fiber reinforced plastic rebars is now possible. Key words: beam, cracking behaviour, cracking moment, crack width, fiber reinforced plastic, flexure, rebars, reinforced concrete, reinforcement ratio.

scholarly journals Performance of Cement-Based Patch Repair Materials in Plain and Reinforced Concrete Members

2016 ◽  
Vol 13 (2) ◽  
pp. 160
Author(s):  
A.H. Al-Saidy
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Reinforced Concrete Beams ◽  
Patch Repair ◽  
Concrete Members ◽  
Repair Materials ◽  
Superior Mechanical Properties ◽  
The Cost

Structural elements such as beams, slabs, and columns may require strengthening or repair during their service life. Different repair materials (RMs) are available and it is usually difficult to choose the best ones, especially when considering the cost of such materials. This paper presents the results of an experimental investigation of patch RMs on plain concrete prisms as well as on reinforced concrete beams. Three cement-based RMs available in the market with different mechanical properties and an ordinary Portland cement (OPC) mix produced in the lab were used in the study. Damage was induced in prisms/beams and then repaired using different materials. The experimental work included assessment of the flexural strength of damaged/repaired plain concrete prisms; slant shear (bond) strength between the concrete and the RM; axial strength of damaged/repaired plain concrete prisms and bond of the repair materials in damaged/repaired reinforced concrete beams loaded to failure. The test results showed that all RMs performed well in restoring the strength of damaged plain concrete. Compatibility of the RMs with substrate concrete was found to be more important in the behavior than superior mechanical properties of the RMs. No difference was noted in the behavior between the RMs in repairing reinforced concrete beams at the tension side. 

Effect of Beam Depth and Longitudinal Reinforcement Ratio on Shear Strength of RC Beams

2010 ◽  
Vol 163-167 ◽  
pp. 1460-1465
Author(s):  
Lei Yu ◽  
Yi Che ◽  
Xin Feng Zheng ◽  
Jin Xin Gong ◽  
Yu Pu Song
Keyword(s):  
Shear Strength ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Shear Behaviour ◽  
Longitudinal Reinforcement ◽  
Test Results ◽  
Beam Depth ◽  
Insight Into

Seven beams were tested to investigate the effects of beam depth and longitudinal reinforcement ratio on the shear strength of reinforced concrete beams. To investigate the effects of beam depth on shear strength, beams of five different sizes were tested. Two beams were designed to investigate the shear behaviour of beams with small percentage of longitudinal reinforcement. In addition to an experimental investigation, a survey of data in the literature was performed to gain insight into the influence of beam depth and longitudinal reinforcement ratio. Based on test results and a data analysis, conclusions regarding the influence of beam depth and longitudinal reinforcement ratio on shear strength of reinforced concrete beams are presented herein.

scholarly journals Experimental Investigations of Reinforced Concrete Beams with Innovative Truss-Shaped Reinforcement System

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1652
Author(s):  
Adam Stolarski ◽  
Jacek Zychowicz
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Longitudinal Reinforcement ◽  
Test Results ◽  
Reinforcement System ◽  
Load Carrying

The purpose of the work is an experimental analysis of the behavior of reinforced concrete beams with a new, patented system of truss-shaped reinforcement. Experimental tests of reinforced concrete beams with conventional reinforcement and with truss-shaped, mass equivalent reinforcement, with two different values of longitudinal reinforcement ratio, were carried out. The testing results of the load-carrying capacity and displacements of beams are presented. The cracking and failure mechanism of beams with a new truss-shaped reinforcement system was also analyzed. The test results for conventionally reinforced beams and with truss-shaped reinforcement were compared. The test results show that the use of the truss reinforcement has an influence on increasing the load-carrying capacity of beams. The amount of this increase depends on the total longitudinal reinforcement ratio and reaches as much as 95% for beams with a low reinforcement ratio and 12% for beams with a higher reinforcement ratio. Based on the investigation of the cracking mechanism, it can be concluded that the failure of the beams with transverse truss-shaped reinforcement occurs with a greater number of smaller cracks, which are more evenly distributed along the length of the cracking zone, and have a shorter range over the cross-section depth, which results in their smaller opening widths. The comparative analysis shows the effectiveness of the proposed reinforcement system, justifying the high potential possibilities of its use for the reinforcement of concrete structural elements.

scholarly journals Behavior of Reinforced Concrete Plates under Pure Torsion

2021 ◽  
Vol 28 (1) ◽  
pp. 84-97
Author(s):  
Omer Ibraheem ◽  
Osama Mukhlif
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Torsional Loading ◽  
Pure Torsion ◽  
Size Change ◽  
Concrete Members ◽  
Strength Capacity ◽  
Concrete Plates

The behavior of reinforced concrete members under torsional loading has interested many researchers during the last decades. These researches focused mainly on the response of reinforced concrete beams at different reinforcement conditions and the size effects. On the other hand, the behavior of concrete plates or slabs has not been investigated clearly under pure and/or combined torsional loading. In the present study, nine reinforced concrete plates were prepared and tested under pure torsion. Effect of steel reinforcement ratio and size change was studied and they have a great effect on the plated strength, capacity, stiffness and ductility. As stated by torsion theories of reinforced concrete beams, the torsional strength of slabs was upgraded also with increasing in cross section and transverse reinforcement ratio.

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

scholarly journals Finite element analysis of reinforced concrete deep beam with large opening

2021 ◽  
Vol 10 (1) ◽  
Author(s):  
Elsayed Ismail ◽  
Mohamed S. Issa ◽  
Khaled Elbadry
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Load Capacity ◽  
Reinforced Concrete Beams ◽  
The Other ◽  
Deep Beam ◽  
Web Openings ◽  
Design Load ◽  
Large Opening

Abstract Background A series of nonlinear finite element (FE) analyses was performed to evaluate the different design approaches available in the literature for design of reinforced concrete deep beam with large opening. Three finite element models were developed and analyzed using the computer software ATENA. The three FE models of the deep beams were made for details based on three different design approaches: (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978), (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006), and Strut and Tie method (STM) as per ACI 318-14 (ACI318 Committee, Building Code Requirements for Structural Concrete (ACI318-14), 2014). Results from the FE analyses were compared with the three approaches to evaluate the effect of different reinforcement details on the structural behavior of transfer deep beam with large opening. Results The service load deflection is the same for the three models. The stiffnesses of the designs of (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) and STM reduce at a load higher than the ultimate design load while the (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) reduces stiffness at a load close to the ultimate design load. The deep beam designed according to (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) model starts cracking at load higher than the beam designed according to (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) method. The deep beam detailed according to (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) and (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) failed due to extensive shear cracks. The specimen detailed according to STM restores its capacity after initial failure. The three models satisfy the deflection limit. Conclusion It is found that the three design approaches give sufficient ultimate load capacity. The amount of reinforcement given by both (Mansur, M. A., Design of reinforced concrete beams with web openings, 2006) and (Kong, F.K. and Sharp, G.R., Magazine of Concrete Res_30:89-95, 1978) is the same. The reinforcement used by the STM method is higher than the other two methods. Additional reinforcement is needed to limit the crack widths. (Mansur, M. A., Design of reinforced concrete beams with web openings, (2006)) method gives lesser steel reinforcement requirement and higher failure load compared to the other two methods.

Sign in / Sign up

Export Citation Format

Share Document