scholarly journals Performance of Cement-Based Patch Repair Materials in Plain and Reinforced Concrete Members

2016 ◽  
Vol 13 (2) ◽  
pp. 160
Author(s):  
A.H. Al-Saidy
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Reinforced Concrete Beams ◽  
Patch Repair ◽  
Concrete Members ◽  
Repair Materials ◽  
Superior Mechanical Properties ◽  
The Cost

Structural elements such as beams, slabs, and columns may require strengthening or repair during their service life. Different repair materials (RMs) are available and it is usually difficult to choose the best ones, especially when considering the cost of such materials. This paper presents the results of an experimental investigation of patch RMs on plain concrete prisms as well as on reinforced concrete beams. Three cement-based RMs available in the market with different mechanical properties and an ordinary Portland cement (OPC) mix produced in the lab were used in the study. Damage was induced in prisms/beams and then repaired using different materials. The experimental work included assessment of the flexural strength of damaged/repaired plain concrete prisms; slant shear (bond) strength between the concrete and the RM; axial strength of damaged/repaired plain concrete prisms and bond of the repair materials in damaged/repaired reinforced concrete beams loaded to failure. The test results showed that all RMs performed well in restoring the strength of damaged plain concrete. Compatibility of the RMs with substrate concrete was found to be more important in the behavior than superior mechanical properties of the RMs. No difference was noted in the behavior between the RMs in repairing reinforced concrete beams at the tension side. 

scholarly journals Influence of tensile softening of concrete on crack development and failure in concrete and reinforced concrete beams

2019 ◽  
Vol 68 (1) ◽  
pp. 213-223 ◽  
Author(s):  
Marta Słowik
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Load Capacity ◽  
Plain Concrete ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Concrete Members ◽  
Cracking Process ◽  
Tensile Softening

In the paper, the own test results were presented. The experimental investigation was focused at determining the cracking and load capacity of beams made of concrete. The beams were characterized by different longitudinal reinforcement ratio from zero — plain concrete beams, through low ratio 0.12% — slightly reinforced concrete beams, middle ratio 0.9% — typical reinforced concrete beams, up to the ratios 1.3% and 1.8% — higher reinforced concrete beams. On the basis of the performed experiments and the results of numerical calculations, the process of crack’s formation and crack’s development in plain concrete, slightly reinforced concrete and reinforced concrete beams with different reinforcement ratio was described. When discussing cracking process in the beams, the contribution of strain softening of tensile concrete in the microcracked zone on the character of beams’ failure was analysed as well. Keywords: civil engineering, concrete and reinforced concrete members, cracking and load capacity.

scholarly journals The analysis of load carrying capacity and cracking of slightly reinforced concrete members in bending

2008 ◽  
Vol 2 (1) ◽  
pp. 065-078
Author(s):  
Marta Słowik
Keyword(s):  
Reinforced Concrete ◽  
Carrying Capacity ◽  
Concrete Beams ◽  
Plain Concrete ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Load Carrying Capacity ◽  
Test Results ◽  
Concrete Members ◽  
Load Carrying

Slightly reinforced concrete members are the members made by concrete with reinforcement less than minimum given in codes for reinforced concrete ones. Plain concrete and slightly reinforced concrete members in bending are treated in the same way during the dimensioning and the influence of longitudinal reinforcement on the load carrying capacity is not taken into account. The mechanism of work and crack formation in slightly reinforced concrete members is not completely recognized. The author’s own research program was made. The experiment was aimed at the determination of cracking moment and load carrying capacity of slightly reinforced concrete beams with different reinforcement ratio. Also plain concrete beams and the typical reinforced concrete beam were tested. The analysis of the obtained values of maximum bending moment and crack’s widths was made according to the reinforcement ratio. The analysis of test results shows how the presence of longitudinal steel bars in concrete members, even when reinforcement ratio is low, changes cracking process and influences the value of cracking moment in flexural members. On the basis of test results, the method how to calculate the load carrying capacity of slightly reinforced concrete elements in bending has been proposed.

Finite Element Analysis of Reinforced Concrete Beams with Exterior FRP Shell

2011 ◽  
Vol 243-249 ◽  
pp. 1461-1465
Author(s):  
Chuan Min Zhang ◽  
Chao He Chen ◽  
Ye Fan Chen
Keyword(s):  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Reinforced Concrete Beams ◽  
Test Results ◽  
Contact Interface ◽  
Accurate Calculation ◽  
Element Analysis

The paper makes an analysis of the reinforced concrete beams with exterior FRP Shell in Finite Element, and compares it with the test results. The results show that, by means of this model, mechanical properties of reinforced concrete beams with exterior FRP shell can be predicted better. However, the larger the load, the larger deviation between calculated values and test values. Hence, if more accurate calculation is required, issues of contact interface between the reinforced concrete beams and the FRP shell should be taken into consideration.

scholarly journals Numerical Sensing of Plastic Hinge Regions in Concrete Beams with Hybrid (FRP and Steel) Bars

Sensors ◽  
2018 ◽  
Vol 18 (10) ◽  
pp. 3255 ◽  
Author(s):  
Fang Yuan ◽  
Mengcheng Chen
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Plastic Hinge ◽  
Reinforcement Ratio ◽  
Reinforced Concrete Beams ◽  
Concrete Members ◽  
Steel Bars ◽  
Hybrid Reinforcement ◽  
Steel Hardening

Fibre-reinforced polymer (FRP)-reinforced concrete members exhibit low ductility due to the linear-elastic behaviour of FRP materials. Concrete members reinforced by hybrid FRP–steel bars can improve strength and ductility simultaneously. In this study, the plastic hinge problem of hybrid FRP–steel reinforced concrete beams was numerically assessed through finite element analysis (FEA). Firstly, a finite element model was proposed to validate the numerical method by comparing the simulation results with the test results. Then, three plastic hinge regions—the rebar yielding zone, concrete crushing zone, and curvature localisation zone—of the hybrid reinforced concrete beams were analysed in detail. Finally, the effects of the main parameters, including the beam aspect ratio, concrete grade, steel yield strength, steel reinforcement ratio, steel hardening modulus, and FRP elastic modulus on the lengths of the three plastic zones, were systematically evaluated through parametric studies. It is determined that the hybrid reinforcement ratio exerts a significant effect on the plastic hinge lengths. The larger the hybrid reinforcement ratio, the larger is the extent of the rebar yielding zone and curvature localisation zone. It is also determined that the beam aspect ratio, concrete compressive strength, and steel hardening ratio exert significant positive effects on the length of the rebar yielding zone.

Study on Retrofitting and Strengthening of Reinforced Concrete Beams Using Fibrous Concrete

2021 ◽  
Vol 9 (8) ◽  
pp. 1676-1684
Author(s):  
Natalia Sharma
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Steel Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Reinforced Concrete Beams ◽  
Cement Matrix ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete

Abstract: Reinforced concrete structures are frequently in need of repair and strengthening as a result of numerous environmental causes, ageing, or material damage under intense stress conditions, as well as mistakes made during the construction process. RC structures are repaired using a variety of approaches nowadays. The usage of FRC is one of the retrofitting strategies. Steel fiber reinforced concrete (SFRC) was used in this investigation because it contains randomly dispersed short discrete steel fibers that operate as internal reinforcement to improve the cementitious composite's characteristics (concrete). The main rationale for integrating small discrete fibers into a cement matrix is to reduce the amount of cement used. The principal reason for incorporating short discrete fibers into a cement matrix is to reduce cracking in the elastic range, increase the tensile strength and deformation capacity and increase the toughness of the resultant composite. These properties of SFRC primarily depend upon length and volume of Steel fibers used in the concrete mixture. In India, the steel fiber reinforced concrete (SFRC) has seen limited applications in several structures due to the lack of awareness, design guidelines and construction specifications. Therefore, there is a need to develop information on the role of steel fibers in the concrete mixture. The experimental work reported in this study includes the mechanical properties of concrete at different volume fractions of steel fibers. These mechanical properties include compressive strength, split tensile strength and flexural strength and to study the effect of volume fraction and aspect ratio of steel fibers on these mechanical properties. However, main aim of the study was significance of reinforced concrete beams strengthened with fiber reinforced concrete layer and to investigate how these beams deflect under strain. The objective of the investigation was finding that applying FRC to strengthen beams enhanced structural performance in terms of ultimate load carrying capacity, fracture pattern deflection, and mode of failure or not.

Numerical Tracking of the Behavior of Repaired Reinforced Concrete Beams by CFRP Sheets against Shear

2020 ◽  
Vol 1002 ◽  
pp. 604-614
Author(s):  
Hayder Hussein H. Kammona ◽  
Muhammad Abed Attiya ◽  
Qasim M. Shakir
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Experimental Results ◽  
Reinforced Concrete Beams ◽  
Cfrp Sheets ◽  
Shear Span ◽  
Concrete Members ◽  
Suggested Technique ◽  
Cfrp Sheet ◽  
Failure Loads

This study simulates a procedure of rehabilitation of reinforced concrete beams with the aid of ANSYS 17 software. In this work, the BIRTH and DEATH procedure (in ANSYS) was adopted to model the post-repairing stage. This aspect has rarely been considered by previous studies that utilized a carbon fiber reinforced polymer (CFRP) sheet when retrofitting. To verify the suggested technique, six specimens were analyzed with two values of shear span-to-depth ratios (3 and 4) and three spaces of CFRP sheets (100mm, 150mm and 200mm). The effect of the repairing process on the structural performance of the retrofitted beam is also investigated.It is found that the suggested technique yielded a good agreement with the experimental results and the maximum differences in the failure loads between the numerical and experimental results were 10% and 4% for shear span-to-depth ratios of 3 and 4, respectively. It was also ascertained that upgrading reinforced concrete members within the early stages of loading showed a better enhancement in the loading capacity compared to upgrading reinforced concrete members close to the juncture of failure.

FLEXURAL DUCTILITY OF STRUCTURAL CONCRETE MEMBERS SUBJECTED TO LIMITED CYCLES OF REPEATED LOADING

2019 ◽  
Vol 6 (1) ◽  
Author(s):  
Nazar Oukaili ◽  
Mohammed Khattab
Keyword(s):  
Reinforced Concrete ◽  
Prestressed Concrete ◽  
Concrete Beams ◽  
Constant Load ◽  
Reinforced Concrete Beams ◽  
Repeated Loading ◽  
Structural Concrete ◽  
Concrete Members ◽  
Flexural Ductility ◽  
High Level

For structural concrete members that may expose to serious earthquake, overload or accident impact, the design of ductility must be given the same importance as the flexural strength. The aim of this investigation is to study the change in ductility of structural concrete flexural members during their exposure to limited cycles of repeated loading. Twenty full-scale beam specimens have been fabricated in to two identical groups; each group consisted of ten specimens. The first group was tested under monotonic static loading to failure and regarded as control beams, while the specimens of the second group were subjected to ten cycles of repeated loading with constant load interval, which ranged between 40% and 60% of ultimate load. Specimens in each group were categorized as follows: two traditional reinforced concrete specimens with different intensity of tension reinforcement; three partially prestressed specimens with bonded strands; three partially prestressed specimens with unbonded strands; and two fully prestressed concrete specimens. The main variable, which was considered for all specimens was the partial prestressing ratio (PPR). It was observed that, the ductility of reinforced concrete beams was insignificantly increased during subjecting to limited repeated loading. For fully prestressed and partially prestressed concrete beams with high level of PPR, the ductility was significantly enhanced, while, it was decreased for specimens with small level of PPR.

Fatigue Behavior of Corroded Reinforced Concrete Beams-a Review

2011 ◽  
Vol 94-96 ◽  
pp. 1523-1526
Author(s):  
Shi Bin Li ◽  
Hong Wei Tang ◽  
Xin Wang
Keyword(s):  
Reinforced Concrete ◽  
Concrete Beams ◽  
Fatigue Behavior ◽  
Concrete Bridges ◽  
Reinforced Concrete Beams ◽  
Rc Structures ◽  
Concrete Members ◽  
Bridge Structures ◽  
Traffic Volumes ◽  
Chloride Attack

Reinforced concrete (RC) structures are widely used in civil engineering for their merits. A good-quality concrete provides a highly alkaline environment that forms a passive film on reinforcement surface, preventing steel bars from corroding. Due to chloride attack or concrete carbonization, corrosion of embedded reinforcement in concrete members is common for RC structures. Much importance should be attached to the fatigue of corroded concrete bridges because they bear not only static loads but also alternate loads. Followed along with the aging of bridge structures, the increase of traffic volumes, the augment of vehicle loads as well as the deterioration of service environment, many corroded concrete bridges are urgently needed security appraisal and residual fatigue life forecast. Fatigue of corroded RC beams is a key problem for the existing corrosion-damaged concrete bridges. But the interrelated research was little. Based on the most new study information, the production on fatigue of corroded concrete beams was listed and analyzed, and the problems on fatigue of corroded concrete beams were indicated.

scholarly journals Calculation of damage RC constructions according to deformation model

2020 ◽  
Vol 2020 (2) ◽  
pp. 99-106
Author(s):  
Yaroslav Blikharskyy ◽  
Keyword(s):  
Mechanical Properties ◽  
Reinforced Concrete ◽  
Concrete Beams ◽  
Concrete Structures ◽  
Physical And Mechanical Properties ◽  
Reinforced Concrete Beams ◽  
Core Material ◽  
Deformation Model ◽  
Reinforced Concrete Structures ◽  
The Impact

This article presents results of a theoretical study of reinforced concrete beams with damaged reinforcement. The change of micro-hardness of a reinforcing rebar’s with a diameter of 20 mm of A500C steel in the radial direction is investigated and the thickness of the heat-strengthened layer is established. It is established that the thickness of the thermo-strengthened steel layer of the reinforcing bar with a diameter of 20 mm of A500C is approximately 3 mm. It is shown that the strength characteristics of this layer are on 50% higher compared to the core material of the rebar, while the plasticity characteristics are lower. The aim of the work is to determine the strength and deformability of reinforced concrete structures without damaging the reinforcement and in case of damage. Determining the impact of changes in the physical characteristics of reinforcement on the damage of reinforced concrete structures, according to the calculation to the valid norms, in accordance with the deformation model. To achieve the goal of the work, theoretical calculations of reinforced concrete beams were performed according to the deformation model, according to valid norms. This technique uses nonlinear strain diagrams of concrete and rebar and is based on an iterative method. According to the research program 3 beam samples were calculated. Among them were undamaged control sample with single load bearing reinforcement of ∅20 mm diameter – BC-1; sample with ∅20 mm reinforcement with damages about 40% without changes in the physical and mechanical properties of reinforcement – BD-2 and sample with ∅20 mm reinforcement with damages about 40% with changes in the physical and mechanical properties of reinforcement – BD-3. The influence of change of physical and mechanical characteristics of rebar’s on bearing capacity of the damaged reinforced concrete beams is established.

Sign in / Sign up

Export Citation Format

Share Document