scholarly journals Blending Lime with Sugarcane Bagasse Ash for Stabilizing Expansive Clay Soils in Subgrade

2021 ◽  
Vol 53 (5) ◽  
pp. 210510
Author(s):  
Zalwango Teddy ◽  
Bazairwe Annette ◽  
Safiki Ainomugisha
Keyword(s):  
Sugarcane Bagasse ◽  
Expansive Soils ◽  
Construction Material ◽  
Dry Weight ◽  
Clay Soils ◽  
Dry Density ◽  
Expansive Clay ◽  
Maximum Dry Density ◽  
Slaked Lime ◽  
Sugarcane Bagasse Ash

Expansive soils constitute one of the most frequently encountered and challenging soils to geotechnical engineers. This study assessed the possibility of utilizing sugarcane bagasse ash (SCBA) by partially replacing slaked lime to stabilize expansive clay soils. The soil samples were picked from Muduuma area, Mpigi district, Central Uganda. Experimental tests of linear shrinkage (LS), plasticity index (PI), and California Bearing Ratio (CBR) were conducted on both unstabilized soil and SCBA-lime treated samples. The SCBA-lime mixture was prepared by partially replacing 5% lime with SCBA at 2, 4, 6, 8, and 10% by weight. Hence, SCBA was used in proportions of 0.1, 0.2, 0.3, 0.4, and 0.5% by dry weight of the soil. The addition of lime greatly lowered the PI and LS, which later increased with the addition of the SCBA. The maximum dry density was generally lowered with the addition of lime and SCBA, from 1.87 g/cm3 to 1.58%. The CBR increased with SCBA-lime addition from 12% for unstabilized soil up to 48% at 6% SCBA replacement. The optimum lime replacement was established as 6% SCBA lime replacement based on CBR criteria. At the 6% optimum, the optimum moisture content (OMC) was 1.7 Mg/m3, LS was 10%, and PI was 20%. This study demonstrated the potentiality of SCBA as a novel construction material, specifically by partially reducing the usage of the unsustainable, non-environmentally friendly lime. It is also expected to enable using currently unsuitable clays from the region.

scholarly journals Influence of Lime for Enhancing Characteristics of Expansive Soils in Road Works

2021 ◽  
Vol 1197 (1) ◽  
pp. 012077
Author(s):  
K.S Chamberlin ◽  
M. Rama Rao
Keyword(s):  
Compressive Strength ◽  
Unconfined Compressive Strength ◽  
Expansive Soils ◽  
Black Cotton Soil ◽  
Dry Density ◽  
Test Results ◽  
Lime Treatment ◽  
Maximum Dry Density ◽  
Slaked Lime ◽  
Black Cotton Soils

Abstract Expansive soils are found in black cotton soils, which swell or shrink in volume when presented to changes in moisture content. Lime treatment is exhaustively used to increment the properties of sensitive and fragile soils. One of the hugest clarifications behind using lime is to decline the developing presentation of the earth soil. The arrangement of extra safeguards improves the reaction of quicklime (CaO) with water, structures hydrated (slaked) lime (Ca (OH)2), and thus earth characteristics. The vast inadequacy of employing lime is growing the deficiency of lime offset earth. Following that, the goal of this study is to see how re-establishing time affects the geotechnical qualities of settled Black cotton soils with lime. These discoveries recommend that adding Lime as a stabilizer works on the strength of black cotton soil. Some of the characteristics of the soil likely to be increased by using stabilizer in this work are UCS (Unconfined Compressive Strength) at different curing periods (7,14,28 and 56 days), CBR (California Bearing Ratio) value at unsoaked and soaked and MDD (Maximum Dry Density) decrease at different lime percentages(%) like 2.4.6.8 and 10. The result showed here untreated soil got stabilized by using the stabilizer in certain extent In this adjustment various rates of cementitious material is added to black cotton soil and directed tests like plasticity, compaction, swell pressure, free swell index(FSI), Coefficient of permeability (k) and CBR(soaked and unsoaked) at various conditions like OMC,OMC+2% water and OMC+5% water, UCS (Unconfined Compressive Strength) was performed. From the test results, it is identified that the stabilization agent decreases plasticity and improves strength characteristics. Addition of stabilizing agent makes the black cotton soil to non-plastic, non-swelling and attains increase CBR values which are greater than 25% for a dosage of 10% lime at OMC but remaining OMC+2%water & OMC+5%water CBR values are not various much difference as per test results. With the addition of lime, the black cotton soil becomes non-plastic, non-swelling, and has high strengths. Treated soils are used as a development material, for example, a subgrade layer in the development of adaptable asphalt pavements for roads.

scholarly journals Experimental Study of the Strength Aspects of Compressed Stabilized Earth Blocks using Marble Dust, Sugarcane Bagasse Ash and Paddy Straw Fiber

2021 ◽  
Vol 889 (1) ◽  
pp. 012025
Author(s):  
Aman Verma ◽  
Tarun Sharma
Keyword(s):  
Water Absorption ◽  
Sugarcane Bagasse ◽  
Construction Material ◽  
Absorption Capacity ◽  
Waste Material ◽  
Dry Density ◽  
Paddy Straw ◽  
Marble Powder ◽  
Sugarcane Bagasse Ash ◽  
Earth Blocks

Abstract The world is facing pollution crises and these cries are due to improper disposal of waste material. This materials are Rice husk ash, bagasseash, waste marble powder, remanings of grains like rice starw and many more. Some of the waste materials can easily be disposable in the construction industry by using them in the concrete or in any other construction material. This paper deals with this waste material to be utilized in the compressed earth blocks. To study the mechanical properties of compressed soil blocks prepared by a combination of various ratios of Marble powder, paddy Straw Fiber and Sugarcane bagasse ash, the compression test, and water absorption test was performed. The marble powder is introduced in the manner to replace soil by 25%, 35%% and 45 %. Paddy Starws fibers are introducedby the replacement percentage of.6%,.8%and 1% whereas the bagasse ash is been introduced in the manner of 8%,10% and 12%This various test shows that the Marble powder Waste increase dry density which helps in increasing the compression Capacity of the brick. Whereas Paddy Straw fiber and bagasse ash decrease the dry density of brick which results in decreasingthe optimum water content of the mixof the brick. Bagasse ash and paddy straw fiber increase the water absorption capacity of the brick.

scholarly journals Stabilization of soft clayey soils with sawdust ashes

2018 ◽  
Vol 162 ◽  
pp. 01006
Author(s):  
Hussein Karim ◽  
Makki Al-Recaby ◽  
Maha Nsaif
Keyword(s):  
Clayey Soil ◽  
Soft Clay ◽  
Physical And Mechanical Properties ◽  
Road Construction ◽  
Dry Weight ◽  
Liquid Limit ◽  
Clay Soils ◽  
Dry Density ◽  
Clayey Soils ◽  
Maximum Dry Density

The problems of soft clayey soils are taken in considerations by many Iraqi geologists and civil engineers, because about 35% of the Iraqi clay soils (especially southern Iraq) are weak. Thus, it is necessary to improve the properties of such soils for road construction by means of using of various stabilizers such as sawdust ash. The main goal of the present study is to stabilize soft clay models with sawdust ash (SDA) additive using different percentages (0, 2, 4, 6, 8 and 10% by dry weight of soil). The results revealed that the additive has adverse effects on the property of soil indices by increasing its liquid limit and plasticity index due to clay content. The mixture of sawdust ashes with soft clay soils improves most other physical and mechanical properties of the soil, as expressed by a general reduction in specific gravity and maximum dry density (MDD), as well as a reduction in the compression coefficients (Cc and Cr) with an increase in SDA content. While increasing the optimum moisture content (OMC) and the undrained shear strength (cu) with the increase in SDA content. The stabilized soils (with 4 and 10% ash content) resulted in low CBR values (1.6-1.2%) which can be used as sub-base. The SDA can be considered as a cheap and acceptable stabilizing agent in road construction for improving most of the geotechnical properties of the soft clayey soil.

scholarly journals Evaluation of Compacted Laterite Soil Admixed with Cement and Hair Fibres as Road Construction Material

2020 ◽  
Vol 8 (1) ◽  
Author(s):  
Johnson Rotimi OLUREMI ◽  
Solomon Idowu Adedokun ◽  
Paul Yohanna ◽  
David A. Fadiran ◽  
Idris O. Azeez
Keyword(s):  
Classification System ◽  
Construction Material ◽  
Statistical Significance ◽  
Road Construction ◽  
Soil Classification ◽  
Dry Weight ◽  
Geotechnical Properties ◽  
Lateritic Soil ◽  
Dry Density ◽  
Maximum Dry Density

A natural lateritic soil classified as A-5 (4) based on American Association of State Highway and Transportation Officials (AASHTO) soil classification system and ML-CL according to Unified Soil Classification System (USCS), was admixed with ordinary Portland cement and synthetic hair fibres (SHF) was evaluated as road construction material. Soil test specimens were made by admixing lateritic soil with up to 4% cement  in 1 % step concentration and up to 12% SHF in step concentration of 2 % by dry weight of the soil and were subjected to British Standard Light (BSL) or Standard Proctor method of compaction, unconfined compressive strength (UCS) and California bearing ratio (CBR) tests. Results indicated a decrease in the values of optimum moisture content (OMC) while no general trend was established for maximum dry density (MDD). The values of UCS and CBR increased as the content of both cement and SHF increased. Analysis of variance (ANOVA) of the results shows some level of statistical significance on some geotechnical properties considered. Regression analysis on the results using Minitab R15 software shows that MDD, OMC, cement and SHF significantly influenced the UCS and CBR values of the stabilized soil with correlation coefficient value (R2) of 82.9 and 83.3% respectively. Based on the results, an optimal blend of 3% cement 9% SHF significantly improved  the soil properties and is recommended  for improving the geotechnical properties of cement/synthetic hair fibre treated lateritic soil as road construction material.

Effect of Lime on Compaction, Strength and Consolidation Characteristics of Pontian Marine Clay

2015 ◽  
Vol 72 (3) ◽  
Author(s):  
Siaw Yah Chong ◽  
Khairul Anuar Kassim
Keyword(s):  
Construction Material ◽  
Soft Clay ◽  
Engineering Properties ◽  
Dry Density ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stabilization Phase ◽  
Compaction Curve ◽  
Stabilized Soil

Marine clay is a problematic construction material, which is often encountered in Malaysian coastal area. Previous researchers showed that lime stabilization effectively enhanced the engineering properties of clay. For soft clay, both strength and consolidation characteristics are equally important to be fully understood for design purpose. This paper presented the effect of lime on compaction, strength and consolidation characteristics of Pontian marine clay. Compaction, unconfined compression, direct shear, Oedometer and falling head permeability tests were conducted on unstabilized and lime stabilized samples at various ages. Specimens were prepared by compaction method based on 95 percent maximum dry density at the wetter side of compaction curve. It was found that lime successfully increased the strength, stiffness and workability of Pontian marine clay; however, the permeability was reduced. Unconfined compressive strength of stabilized soil was increased by 49 percent at age of 56 days whereas compressibility and permeability was reduced by 48 and 67 percent, respectively. From laboratory tests, phenomenon of inconsistency in engineering characteristics was observed for lime stabilized samples below age of 28 days. This strongly proved that lime stabilized soil underwent modification phase before stabilization phase which provided the long term improvement.

scholarly journals Utilization of Sugarcane Bagasse Ash from Power Co-generation Boilers as a Supplementary Cementitious Material

2021 ◽  
Vol 2 (2) ◽  
Author(s):  
Safiki Ainomugisha ◽  
Bisaso Edwin ◽  
Bazairwe Annet
Keyword(s):  
Compressive Strength ◽  
Portland Cement ◽  
Sugarcane Bagasse ◽  
Low Income ◽  
Ordinary Portland Cement ◽  
Construction Material ◽  
Sustainable Construction ◽  
Partial Replacement ◽  
Hardened Concrete ◽  
Sugarcane Bagasse Ash

Concrete has been the world’s most consumed construction material, with over 10 billion tons of concrete annually. This is mainly due to its excellent mechanical and durability properties plus high mouldability. However, one of its major constituents; Ordinary Portland Cement is reported to be expensive and unaffordable by most low-income earners. Its production contributes about 5%–8% of global CO2 greenhouse emissions. This is most likely to increase exponentially with the demand of Ordinary Portland Cement estimated to rise by 200%, reaching 6000 million tons/year by 2050.  Therefore, different countries are aiming at finding alternative sustainable construction materials that are more affordable and offer greener options reducing reliance on non-renewable sources. Therefore, this study aimed at assessing the possibility of utilizing sugarcane bagasse ash from co-generation in sugar factories as supplementary material in concrete. Physical and chemical properties of this sugarcane bagasse ash were obtained plus physical and mechanical properties of fresh and hardened concrete made with partial replacement of Ordinary Portland Cement. Cost-benefit analysis of concrete was also assessed. The study was carried using 63 concrete cubes of size 150cm3 with water absorption studied as per BS 1881-122; slump test to BS 1881-102; and compressive strength and density of concrete according to BS 1881-116. The cement binder was replaced with sugarcane bagasse ash 0%, 5%, 10%, 15%, 20%, 25% and 30% by proportion of weight. Results showed the bulk density of sugarcane bagasse ash at 474.33kg/m3, the specific gravity of 1.81, and 65% of bagasse ash has a particle size of less than 0.28mm. Chemically, sugarcane bagasse ash contained SiO2, Fe2O3, and Al2O3 at 63.59%, 3.39%, and 5.66% respectively. A 10% replacement of cement gave optimum compressive strength of 26.17MPa. This 10% replacement demonstrated a cost saving of 5.65% compared with conventional concrete. 

scholarly journals Compaction and Plasticity Comparative Behaviour of Soft Clay Treated with Coarse and Fine Sizes of Ceramic Tiles

2018 ◽  
Vol 34 ◽  
pp. 01012 ◽  
Author(s):  
Mohammed Ali Mohammed Al-Bared ◽  
Aminaton Marto ◽  
Indra Sati Hamonangan Harahap ◽  
Fauziah Kasim
Keyword(s):  
Soil Stabilization ◽  
Soft Soil ◽  
Soft Clay ◽  
Cost Effective ◽  
Dry Weight ◽  
Dry Density ◽  
Ceramic Tiles ◽  
Marine Clay ◽  
Maximum Dry Density ◽  
Stiff Soil

Recycled blended ceramic tiles (RBT) is a waste material produced from ceramic tile factories and construction activities. RBT is found to be cost effective, sustainable, environmental-friendly and has the potential to be used as an additive in soft soil stabilization. Recent reports show that massive amounts of RBT are dumped into legal or illegal landfills every year consuming very large spaces and creating major environmental problems. On the other hand, dredged marine clay obtained from Nusajaya, Johor, Malaysia has weak physical and engineering characteristics to be considered as unsuitable soft soil that is usually excavated, dumped into landfills and replaced by stiff soil. Hence, this study investigates the suitability of possible uses of RBT to treat marine clay. Laboratory tests included Standard proctor tests and Atterberg limits tests. The plasticity of marine clay was evaluated by adding 10%, 20%, 30% and 40% of 0.3 mm RBT. In addition, the compaction behaviour of treated marine clay was compared by adding two different sizes (0.3 mm and 1.18 mm diameter) of RBT. For both coarse and fine sizes of RBT, 10%, 20%, 30% and 40% of the dry weight of the soft clay were added. The mixture of each combination was examined in order to evaluate the Maximum Dry Density (MDD) and the optimum moisture content (OMC) for the treated soft clay. MDD and OMC for soft untreated samples were 1.59 Mg/m3 and 22%, respectively. Treated samples with 10%, 20%, 30% and 40% of 0.30 mm size RBT resulted in a significant reduction of OMC ranged from 19 to 15% while MDD resulted in increment ranged from 1.69 to 1.77 Mg/m3. In addition, samples treated with 10%, 20%, 30% and 40% of 1.18 mm size RBT resulted in major reduction of OMC ranged from 15 to 13.5% while MDD increased effectively from 1.75 to 1.82 Mg/m3. For all mix designs of soft clay-RBT, MDD was gradually increasing and OMC was sharply reducing with further increments of both sizes of RBT.

scholarly journals Engineering behaviour of stabilized laterite and kaolin using lignin

2018 ◽  
Vol 250 ◽  
pp. 01008
Author(s):  
Tuan Noor Hasanah Tuan Ismail ◽  
Siti Aimi Nadia Mohd Yusoff ◽  
Ismail Bakar ◽  
Devapriya Chitral Wijeyesekera ◽  
Adnan Zainorabidin ◽  
...  
Keyword(s):  
Moisture Content ◽  
Unconfined Compressive Strength ◽  
Laboratory Tests ◽  
Dry Weight ◽  
Optimum Moisture Content ◽  
Soil Samples ◽  
Dry Density ◽  
Laterite Soil ◽  
Maximum Dry Density ◽  
Steady Rate

Soils at many sites do not always have enough strength to bear the structures constructed over them and some of the soil may need to be stabilized in order to improve their geotechnical properties. In this paper, routine laboratory tests were critically carried out to investigate the efficacy of lignin in improving the strength behaviour of the soils. Two different soil samples (laterite and kaolin) were studied and mixed with different proportions of lignin (2% and 5% of dry weight of soil), respectively. Unconfined Compressive Strength (UCS) characteristics evaluated in this study were done on samples at their maximum dry density and optimum moisture content (obtained from compaction tests). The UCS tests on all the specimens were carried out after 0, 7, 15, 21 and 30 days of controlled curing. The research results showed that the addition of lignin into kaolin reduced its maximum dry density while giving progressively higher optimum moisture content. Contrarily, with the laterite soil, both maximum dry density and optimum moisture content simultaneously increased when lignin was added into the soils. The UCS results showed that the the stabilized laterite with 2% lignin continued to gain strength significantly at a fairly steady rate after 7 days. Unfortunately, lignin did not show a significant effect in kaolin.

scholarly journals Potency Of Sugarcane Bagasse Ash Partial Substitution Of Cement In Concrete

2019 ◽  
Author(s):  
Ismail Marzuki ◽  
Erniati Bachtiar ◽  
ASRI MULYA SETIAWAN ◽  
SRIGUSTY
Keyword(s):  
Compressive Strength ◽  
Sugarcane Bagasse ◽  
Construction Material ◽  
Standard Condition ◽  
Strength Test ◽  
Test Method ◽  
Partial Substitution ◽  
Sugar Factory ◽  
Compressive Strength Test ◽  
Sugarcane Bagasse Ash

the availability of sugarcane bagasse ash produced by Arasoe Sugar Factory, it is not used utilized. That sugarcane bagasse ash has size very fine that it can pollute the air. The sugarcane bagasse ash has silicate content, and it has pozzolan properties. The needs of construction material are something that to think about that. It is an alternative to substitute the using of cement in concrete construction. This study is aimed to find the potential of sugarcane bagasse ash in Arasoe Sugar Factory for partial substitution of cement in concrete. The sample made from the variety of sugarcane bagasse ash 0%, 2.5%, 5%, and 7.5% as partial substitution of cement in concrete. The ratio of water and cement is 0.45. The specimen of concrete is taken care in standard condition at the laboratory and compressive strength test when the sample is in 28, 45, and 62 days old. The compressive strength test refers to ASTM C39/ C39M-01 (Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens). The development of compressive strength of concrete with many variations of sugarcane bagasse ash 0% 2.5%, 5% is increasing along with the age of concrete, however in contrast with 7.5% of sugarcane bagasse ash the decreasing in 60 days old later. Partial substitute of sugarcane bagasse ash in concrete is possible to do in an amount about 5% of sugarcane bagasse ash

scholarly journals Influence of Energy on Compaction Characteristics of High Expansive Soils

2020 ◽  
Vol 9 (5) ◽  
pp. 1344-1348
Keyword(s):  
Moisture Content ◽  
Soil Type ◽  
Expansive Soils ◽  
Unit Weight ◽  
Dry Density ◽  
Maximum Dry Density ◽  
Compaction Characteristics ◽  
Dry Unit Weight ◽  
Comparison Results ◽  
Compaction Energy

Each soil type has different behavior with regard to determination of maximum dry density and optimum moisture content and therefore any soil type has its own compaction requirements for experimental purposes and for control the compaction in the field. The general purpose of this study is to a better understanding of the compaction characteristics of high expansive soils, with emphasis on the relationships of moisture content and dry density of high expansive soils at a range of compaction energy levels. To achieve this purpose, high expansive soils samples were subjected to Atterberg limit and a set of laboratory compaction tests to find compaction characteristics namely; maximum dry unit weight and optimum water content of high expansive soils at different compaction energy (compaction effort) for different number of hammer blows per each layer range from 10 to 50, which varied the energy per unit volume from 356 KN/m3 to 1188 KN/m3.Rather than single peak compaction curves, the most achieved compaction curves are an irregular one and half peak compaction curves. According to the comparison results of different compaction energy, it was concluded that the maximum dry unit weight of high expansive soil was not highly affected by gradually increase of applied energy. The results showed that, the maximum dry density of tested expansive soils sample increased from 1.48g/cm3 to 1.6g/cm3 with increase of compaction energy from 356 KN/m3 to 1188 KN/m3.

Sign in / Sign up

Export Citation Format

Share Document