scholarly journals Preparation and Characterization of an Aqueous Suspension Containing Nanoparticles of Poly (DL-lactic Acid)/Irinotecan/Polyethylene Glycol Monostearate

Author(s):  
Yoshiaki Machida ◽  
Hiraku Onishi ◽  
Hidetaka Miura ◽  
Yoshiharu Machida
1985 ◽  
Vol 48 (12) ◽  
pp. 1028-1035 ◽  
Author(s):  
DENNIS A. ROMERO ◽  
LARRY L. McKAY

Isolation and characterization of a Lactobacillus species capable of proper acid production in a sausage environment is described. The isolate from sausage, categorized as a lactobacillus in the subgenus Streptobacterium, was designated Lactobacillus sp. DR1. Growth occurred at 5 and 42°C but not at 45°C. Fructose, galactose, glucose, mannose, melibiose, N-acetylglucosamine, ribose, sucrose and trehalose were fermented. Gas production from glucose was not observed. In MRS glucose broth, D(−) and L(+) lactic acid were produced. Lactobacillus sp. DR1 contained a single cryptic plasmid of approximately 30 megadaltons (Mdal). In sausage fermentation trials, both Lactobacillus sp. DR1 and plasmid-free derivative DR1C lowered the pH to below 5.3 after 8 h in the smokehouse. Conjugation was demonstrated through the transfer of plasmid pAMβ1, which encodes erythromycin resistance, from Streptococcus lactis 2301β to Lactobacillus sp. DR1. Mutanolysin-generated protoplasts could be regenerated using 0.5 M ammonium chloride, lactose, maltose or sucrose as osmotic stabilizers. Regeneration frequencies ranged from less than 1.0% up to 35%; however, transformation of Lactobacillus sp. DR1 protoplasts by plasmid DNA in the presence of polyethylene glycol (PEG) was unsuccessful.


2019 ◽  
Vol 821 ◽  
pp. 89-95
Author(s):  
Wanasorn Somphol ◽  
Thipjak Na Lampang ◽  
Paweena Prapainainar ◽  
Pongdhorn Sae-Oui ◽  
Surapich Loykulnant ◽  
...  

Poly (lactic acid) or PLA was reinforced by nanocellulose and polyethylene glycol (PEG), which were introduced into PLA matrix from 0 to 3 wt.% to enhance compatibility and strength of the PLA. The nanocellulose was prepared by TEMPO-mediated oxidation from microcrystalline cellulose (MCC) powder and characterized by TEM, AFM, and XRD to reveal rod-like shaped nanocellulose with nanosized dimensions, high aspect ratio and high crystallinity. Films of nanocellulose/PEG/PLA nanocomposites were prepared by solvent casting method to evaluate the mechanical performance. It was found that the addition of PEG in nanocellulose-containing PLA films resulted in an increase in tensile modulus with only 1 wt% of PEG, where higher PEG concentrations negatively impacted the tensile strength. Furthermore, the tensile strength and modulus of nanocellulose/PEG/PLA nanocomposites were higher than the PLA/PEG composites due to the existence of nanocellulose chains. Visual traces of crazing were detailed to describe the deformation mechanism.


Polymers ◽  
2021 ◽  
Vol 13 (6) ◽  
pp. 948
Author(s):  
Nicola Zerbinati ◽  
Sabrina Sommatis ◽  
Cristina Maccario ◽  
Maria Chiara Capillo ◽  
Giulia Grimaldi ◽  
...  

(1) Background: Injectable hyaluronic acid (HA) dermal fillers are used to restore volume, hydration and skin tone in aesthetic medicine. HA fillers differ from each other due to their cross-linking technologies, with the aim to increase mechanical and biological activities. One of the most recent and promising cross-linkers is polyethylene glycol diglycidyl ether (PEGDE), used by the company Matex Lab S.p.A., (Brindisi, Italy) to create the HA dermal filler PEGDE family. Over the last few years, several studies have been performed to investigate the biocompatibility and biodegradability of these formulations, but little information is available regarding their matrix structure, rheological and physicochemical properties related to their cross-linking technologies, the HA content or the degree of cross-linking. (2) Methods: Seven different injectable HA hydrogels were subjected to optical microscopic examination, cohesivity evaluation and rheological characterization in order to investigate their behavior. (3) Results: The analyzed cross-linked dermal fillers showed a fibrous “spiderweb-like” matrix structure, with each medical device presenting different and peculiar rheological features. Except for HA non cross-linked hydrogel 18 mg/mL, all showed an elastic and cohesive profile. (4) Conclusions: The comparative analysis with other literature works makes a preliminary characterization of these injectable medical devices possible.


2021 ◽  
Vol 709 (1) ◽  
pp. 012020
Author(s):  
Evy Rossi ◽  
Akhyar Ali ◽  
Raswen Efendi ◽  
Fajar Restuhadi ◽  
Yelmira Zalfiatri ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document