THE INFLUENCE OF CENTRE BOW LENGTH ON SLAMMING LOADS AND MOTIONS OF LARGE WAVE-PIERCING CATAMARANS

2021 ◽  
Vol 160 (A1) ◽  
Author(s):  
J R Shahraki ◽  
G A Thomas ◽  
M R Davis
Keyword(s):  
Wave Height ◽  
Full Scale ◽  
Bending Moments ◽  
Regular Waves ◽  
Large Wave ◽  
Towing Tank ◽  
Segmented Model ◽  
Model Experiments ◽  
Slamming Load ◽  
Wave Induced

The effect of various centre bow lengths on the motions and wave-induced slamming loads on wave-piercing catamarans is investigated. A 2.5 m hydroelastic segmented model was tested with three different centre bow lengths and towed in regular waves in a towing tank. Measurements were made of the model motions, slam loads and vertical bending moments in the model demi-hulls. The model experiments were carried out for a test condition equivalent to a wave height of 2.68 m and a speed of 20 knots at full scale. Bow accelerations and vertical bending moments due to slamming showed significant changes with the change in centre bow, the longest centre bow having the highest wave-induced loads and accelerations. The increased volume of displaced water which is constrained beneath the bow archways is identified as the reason for this increase in the slamming load. In contrast it was found that the length of centre bow has a relatively small effect on the heave and pitch motions in slamming conditions.

The Influences of Centre Bow Length on Slamming Loads and Motions of Large Wave-Piercing Catamarans

2018 ◽  
Vol Vol 160 (A1) ◽  
Author(s):  
J R Shahraki ◽  
G A Thomas ◽  
M R Davis
Keyword(s):  
Wave Height ◽  
Full Scale ◽  
Bending Moments ◽  
Regular Waves ◽  
Large Wave ◽  
Towing Tank ◽  
Segmented Model ◽  
Model Experiments ◽  
Slamming Load ◽  
Wave Induced

The effect of various centre bow lengths on the motions and wave-induced slamming loads on wave-piercing catamarans is investigated. A 2.5 m hydroelastic segmented model was tested with three different centre bow lengths and towed in regular waves in a towing tank. Measurements were made of the model motions, slam loads and vertical bending moments in the model demi-hulls. The model experiments were carried out for a test condition equivalent to a wave height of 2.68 m and a speed of 20 knots at full scale. Bow accelerations and vertical bending moments due to slamming showed significant changes with the change in centre bow, the longest centre bow having the highest wave-induced loads and accelerations. The increased volume of displaced water which is constrained beneath the bow archways is identified as the reason for this increase in the slamming load. In contrast it was found that the length of centre bow has a relatively small effect on the heave and pitch motions in slamming conditions.

Symmetric Response of a Hydroelastic Scaled Container Ship Model in Regular and Irregular Waves

2014 ◽  
Author(s):  
Sheng Peng ◽  
Pandeli Temarel ◽  
S. S. Bennett ◽  
Weiguo Wu ◽  
Zhengguo Liu ◽  
...  
Keyword(s):  
Full Scale ◽  
Irregular Waves ◽  
Container Ship ◽  
Bending Moments ◽  
Segmented Model ◽  
Numerical Predictions ◽  
Hull Structure ◽  
Strip Theory ◽  
Head Waves ◽  
Wave Induced

Wave-induced vibrations, such as whipping and springing, of container carriers have been attracting much attention because of their effects on hull-girder bending moments and fatigue damage. An investigation has been carried out comparing experimental measurements and numerical predictions of symmetric wave-induced loads (i.e. vertical bending moment) of the latest River-sea link container ship design, LPP = 130 m. The dual mission characteristics, namely rivers and open seas, make this type of ship an extremely interesting type of container carrier, particularly in terms of springing and whipping. A backbone beam segmented model is used in the experiments with the focus on springing- and whipping-induced vertical bending moments, for the model travelling at Fn = 0.21 in regular and long-crested irregular head waves, of 2.5m full-scale height or significant wave height. In addition higher order (harmonics) vertical bending moments (VBM) are also extracted from the experiments. The measurements are taken at amidships and the fore and aft quarters. Numerical predictions, for both the full-scale vessel and segmented model, are obtained using the two-dimensional linear hydroelasticity theories, where the hull structure is idealized as a non-uniform beam and the fluid actions evaluated using strip theory. The measured model test results, in relatively moderate conditions based on a particular area of operation for this low-draught vessel, indicate that nonlinear springing accounts for a significant portion of the total wave-induced bending moments in regular and, to an extent, irregular waves and slamming effects are small due to the operational area selected. The numerical predictions in regular waves show that linear hydroelasticity analysis can only predict similar trends in the variation of the VBM and the resonance peak. On the other hand, in long crested irregular waves the linear hydroelasticity analysis provides peak statistics that are commensurate with the measurements. The numerical predictions were obtained for two variants, having L = LPP and L = 0.9 LPP, the latter corresponding to the length of the backbone.

scholarly journals Breaking-Wave Induced Transient Pore Pressure in a Sandy Seabed: Flume Modeling and Observations

2021 ◽  
Vol 9 (2) ◽  
pp. 160
Author(s):  
Changfei Li ◽  
Fuping Gao ◽  
Lijing Yang
Keyword(s):  
Pore Pressure ◽  
Wave Height ◽  
Wave Breaking ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Regular Waves ◽  
Large Wave ◽  
Pore Pressures ◽  
Linear Waves ◽  
Wave Induced

Previous studies on wave-induced pore pressure in a porous seabed mainly focused on non-breaking regular waves, e.g., Airy linear waves or Stokes non-linear waves. In this study, breaking-wave induced pore pressure response in a sandy seabed was physically simulated with a large wave flume. The breaking-wave was generated by superimposing a series of longer waves onto the foregoing shorter waves at a specified location. Water surface elevations and the corresponding pore pressure in the process of wave breaking were measured simultaneously at three typical locations, i.e., at the rear, just at, and in front of the wave breaking location. Based on test results, characterization parameters are proposed for the wave surface elevations and the corresponding pore-pressures. Flume observations indicate that the wave height was greatly diminished during wave breaking, which further affected the pore-pressure responses. Moreover, the measured values of the characteristic time parameters for the breaking-wave induced pore-pressure are larger than those for the free surface elevation of breaking-waves. Under the action of incipient-breaking or broken waves, the measured values of the amplitude of transient pore-pressures are generally smaller than the predicted results with the analytical solution by Yamamoto et al. (1978) for non-breaking regular waves with equivalent values of characteristic wave height and wave period.

DETERMINATION OF WAVE SLAMMING LOADS ON HIGH-SPEED CATAMARANS BY HYDROELASTIC SEGMENTED MODEL EXPERIMENTS

2021 ◽  
Vol 153 (A3) ◽  
Author(s):  
J Lavroff ◽  
M R Davis ◽  
D S Holloway ◽  
G Thomas
Keyword(s):  
Relative Motion ◽  
High Speed ◽  
Wave Profile ◽  
Full Scale ◽  
Bending Moments ◽  
Towing Tank ◽  
Segmented Model ◽  
Wave Slamming ◽  
Dynamic Wave

A 2.5m hydroelastic segmented catamaran model has been developed based on the 112m INCAT wave-piercer catamaran to simulate the vibration response during the measurement of dynamic slam loads in head seas. Towing tank tests were performed in regular seas to measure the dynamic slam loads acting on the centre bow and vertical bending moments acting in the demihulls of the catamaran model as a function of wave frequency and wave height to establish the operational loads acting on the full-scale 112m INCAT catamaran vessel. Peak slam forces measured on the bow of the model are found to approach the weight of the model, this being similar to the findings of full-scale vessel trials. A review of the motions of the hydroelastic segmented catamaran model found that the heave and pitch motions give a good indication of slamming severity in terms of the dimensionless heave and pitch accelerations. The dynamic wave slam forces are closely related to the relative motion between the bow and the incident wave profile.

Springing Responses Analysis and Segmented Model Testing on a 550,000 DWT Ore Carrier

2016 ◽  
Author(s):  
Hui Li ◽  
Di Wang ◽  
Cheng Ming Zhou ◽  
Kaihong Zhang ◽  
Huilong Ren
Keyword(s):  
Natural Frequency ◽  
Design Stage ◽  
Resonant Vibration ◽  
Bending Moments ◽  
Wave Loads ◽  
Regular Waves ◽  
Segmented Model ◽  
Ship Model ◽  
Hull Structure ◽  
Stiffness Distribution

For ultra large ore carriers, springing response should be analyzed in the design stage since springing is the steady-state resonant vibration and has an important effect on the fatigue strength of hull structure. The springing response of a 550,000 DWT ultra large ore carrier has been studied by using experimental and numerical methods. A flexible ship model composed of nine segments was used in the experiment. The model segments were connected by a backbone with varying section, which can satisfy the request of natural frequency and stiffness distribution. The experiments in regular waves were performed and the motions and wave loads of the ship were measured. The experimental results showed that springing could be excited when the wave encounter frequency coincides with half or one-third the flexural natural frequency of the ship. In this paper, the analysis of the hydroelastic responses of the ultra large ore carrier was also carried out using a 3-D hydroelastic method. Comparisons between experimental and numerical results showed that the 3-D hydroelastic method could predict the motions and the vertical bending moments quite well. Based on this numerical method, the fatigue damage was estimated and the contribution of springing was analyzed.

Effect of Heavy Weather Maneuvering on the Wave-Induced Vertical Bending Moments in Ship Structures

1990 ◽  
Vol 34 (01) ◽  
pp. 60-68 ◽  
Author(s):  
C. Guedes Soares
Keyword(s):  
Wave Height ◽  
Significant Wave Height ◽  
Decision Rules ◽  
Bending Moment ◽  
Ship Motions ◽  
Bending Moments ◽  
Significant Wave ◽  
Course Changes ◽  
Wave Induced ◽  
Vertical Bending Moment

Statistical data are collected so as to quantify the probability of occurrence of voluntary course changes in heavy weather as well as their dependence on significant wave height and on ship heading. Decision rules are established about when and how to change course, on the basis of the analysis of operational data and of interviews with experienced shipmasters. A Monte Carlo simulation is performed so as to determine how an omnidirectional distribution of initial headings is changed by voluntary course changes depending on the significant wave height. Finally, the effect of the nonuniform distribution of headings on the mean wave-induced vertical bending moment is calculated. It is shown that although heavy weather maneuvering eases the ship motions, it can increase the wave-induced bending moments and thus increase the probability of structural failure.

Experimental and Numerical Investigation of the Wave-Induced Loads on a Deep-V Catamaran in Regular Waves

2013 ◽  
Author(s):  
Musa B. Bashir ◽  
Longbin Tao ◽  
Mehmet Atlar ◽  
Robert S. Dow
Keyword(s):  
Wave Loads ◽  
Forward Speed ◽  
Regular Waves ◽  
Hull Form ◽  
Proper Understanding ◽  
Towing Tank ◽  
Centre Of Gravity ◽  
Numerical Predictions ◽  
New Research ◽  
Wave Induced

This paper presents the results of towing tank tests carried out to predict the wave loads in regular wave conditions on a Deep-V hull form catamaran model. The experiments were carried out at the Newcastle University towing tank using a segmented model of the university’s new research vessel, “The Princess Royal”. The vessel is a twin hull with a Deep-V shape cross-section. The model, divided into two parts at the cross-deck level, was fitted with a 5-axis load cell at the position of the vessel’s centre of gravity in order to measure the motions response and wave loads due to the encountered waves. The longitudinal, side and vertical forces, along with the prying and yaw splitting moments were measured. The results obtained were further compared with those from numerical predictions carried out using a 3D panel method code based on potential flow theory that uses Green’s Function with the forward speed correction in the frequency domain. The results highlight reasonable correlations between the measurements and the predictions as well as the need for a proper understanding of the response of the multihull vessels to the wave-induced loads due to the non-linearity that have been observed in the experimental measurements of wave loads.

Study on vertical motion reduction of a trimaran based on collaborative controlled appendages

2020 ◽  
Vol 17 (6) ◽  
pp. 172988142097677
Author(s):  
Zhilin Liu ◽  
Linhe Zheng ◽  
Guosheng Li ◽  
Shouzheng Yuan ◽  
Songbai Yang
Keyword(s):  
Experimental Study ◽  
Vertical Motion ◽  
Model Tests ◽  
Wave Period ◽  
Regular Waves ◽  
Towing Tank ◽  
Vertical Stability ◽  
Stabilization Control ◽  
Stability Performance

In recent years, the trimaran as a novel ship has been greatly developed. The subsequent large vertical motion needs to be studied and resolved. In this article, an experimental study for a trimaran vertical stabilization control is carried out. Three modes including the bare trimaran (the trimaran without appendages, the trimaran with fixed appendages, and the trimaran with controlled appendages) are performed through model tests in a towing tank. The model tests are performed in regular waves. The range of wave period is 2.0–4.0 s, and the speed of the carriage is 2.93 and 6.51 m/s. The results of the three modes show the fixed appendages and the actively controlled appendages are all effective for the vertical motion reduction of the trimaran. Moreover, the controlled appendages are more effective for the vertical stability performance of the trimaran.

First Ocean Going Ships With Springing and Whipping Included in the Ship Design

2011 ◽  
Author(s):  
Gaute Storhaug ◽  
Erlend Moe ◽  
Ricardo Barreto Portella ◽  
Tomazo Garzia Neto ◽  
Nelson Luiz Coelho Alves ◽  
...  
Keyword(s):  
Fatigue Damage ◽  
Current Model ◽  
Life Time ◽  
Model Tests ◽  
Full Scale ◽  
Development Projects ◽  
Transient Vibration ◽  
Hull Girder ◽  
Fatigue Evaluation ◽  
Wave Induced

It is well known that ships vibrate due to waves. The wave induced vibrations of the hull girder are referred to as springing (resonance) and whipping (transient vibration from impacts). These vibrations contribute to the fatigue damage of fatigue sensitive details. An Ore Carrier of 400 000 dwt is currently being built by DSME, and at time of delivery, it will be the world’s largest bulk (ore) carrier. The scantlings of large ships must be carefully designed with respect to global loading, and when extending the design beyond experience, it is also wise to consider all aspects that may affect operation and the life time costs. The vessel will also enter a long term contract and is therefore to be evaluated for 30 year Brazil-China operation. In order to minimize the risk of fatigue damage, the vessel is designed according to DNV’s class notation CSA-2 requiring direct calculations of the loading and strength. Further it has been requested to include the effect of springing and whipping in the design. Reliable numerical tools for assessing the additional fatigue effect of vibrations are non-existing. DNV has, however, developed an empirical guidance on how the additional effect may be taken into account based on previous development projects related to the effect of vibrations on large ore carriers Due to the size and route of operation of the new design, it has, however, been required by the owner to carry out model tests in both ballast and cargo condition in order to quantify the contribution from vibration. The results from this project have been used for verification and further calibration of DNV’s existing empirical guidance. A test program has been designed for the purpose of evaluating the consequence in head seas for the Brazil to China trade. Full scale measurements from previous development projects of ore carriers and model tests have been utilized to convert the current model tests results into estimated full scale results for the 400 000 dwt vessels. It is further important to carefully consider how the vibrations are to be included in the design verification, and to develop a procedure for taking into account the vibrations which results in reasonable scantlings based on in-service experience with similar designs and trades. This procedure has been developed, and a structural verification has been carried out for the design. The final outcome of the model test was in line with previous experience and in overall agreement with DNV’s empirical guidance, showing a significant contribution from vibrations to the fatigue damage. The springing/whipping vibrations more than doubled the fatigue damage compared to fatigue evaluation of the isolated wave induced loading. The cargo condition vibrated relatively more than experienced on smaller vessels. Various sources to establish the wave conditions for the Brazil to China ore trade were used, and the different sources resulted in significant differences in the predicted fatigue life of the design.

Sign in / Sign up

Export Citation Format

Share Document