scholarly journals Potentials of the assessment of the wood quality in standing trees by applying acoustic methods

2020 ◽  
pp. 121-132
Author(s):  
Ivana Živanović ◽  
Nebojša Todorović ◽  
Ljubinko Rakonjac ◽  
Filip Jovanović
Keyword(s):  
Wood Density ◽  
Wood Quality ◽  
Wood Properties ◽  
Acoustic Velocity ◽  
Wave Velocities ◽  
Acoustic Methods ◽  
Standing Trees ◽  
The Right ◽  
Evaluation Of Data

Based on literature sources, the stress wave and ultrasound methods and tools designed for the evaluation of the effects of decay on wood are discussed in this paper. To make a review of the results obtained in numerous studies, the analytic-synthetic method was used and the evaluation of data was conducted. The results revealed high correlations between the measured properties and the actual wood quality. A number of studies show that the acoustic wave velocities correlate well to wood density and other wood properties. Changes in the acoustic velocity and wood density variations caused by decay have also been detected successfully using the ultrasonic tools. This means that wood quality can be assessed in situ and that the methods and devices in question can help us make the right decisions. Still, it must be pointed out that all the methods and devices used are only measuring and quantifying tools, and practical human experience cannot be replaced by any measuring tools.

Genetic relationships between wood quality traits and diameter growth of juvenile core wood in Sitka spruce

2013 ◽  
Vol 43 (1) ◽  
pp. 1-6 ◽  
Author(s):  
S.G. Kennedy ◽  
A.D. Cameron ◽  
S.J. Lee
Keyword(s):  
Growth Rate ◽  
Genetic Correlation ◽  
Modulus Of Elasticity ◽  
Genetic Relationships ◽  
Wood Quality ◽  
Wood Properties ◽  
Sitka Spruce ◽  
Acoustic Velocity ◽  
Picea Sitchensis ◽  
Good Growth

The trend towards shorter rotations in planted conifer stands has resulted in a reduction in the proportion of mature wood relative to juvenile core wood, raising concerns that the mechanical performance of sawn battens will be affected. The potential to improve the wood quality of the juvenile core of Sitka spruce (Picea sitchensis (Bong.) Carrière) without compromising growth rate was investigated. Rapid and inexpensive indirect methods of assessing wood properties on standing trees using a Pilodyn gun and acoustic velocity were compared with direct measurements made on wood samples cut from the juvenile core. Strong genetic correlations were observed between Pilodyn gun values and direct measures of density (–0.76) and between the square of acoustic velocity and modulus of elasticity (0.73). The genetic correlation between the square of acoustic velocity and microfibril angle was also strong (–0.84). These results suggest that indirect assessments of wood properties within juvenile core wood are sufficiently reliable for these techniques to be used in the Sitka spruce breeding programme. Although a strong negative genetic correlation between diameter at breast height and density was noted (–0.79), sufficient variation exists within the breeding population to select families with both good growth rate and high modulus of elasticity wood.

Implications of selection history on genetic architecture of growth, form, and wood-quality traits in Pinus radiata

2008 ◽  
Vol 38 (9) ◽  
pp. 2372-2381 ◽  
Author(s):  
S. Kumar ◽  
R. D. Burdon ◽  
G. T. Stovold ◽  
L. D. Gea
Keyword(s):  
Wood Density ◽  
Pinus Radiata ◽  
Wood Quality ◽  
Genetic Correlations ◽  
Wood Properties ◽  
Radiata Pine ◽  
Single Pair ◽  
Narrow Sense Heritability ◽  
Tree Form ◽  
Selection History

Clonal trials of Pinus radiata D. Don (radiata pine), representing two populations (or breeds), one selected for growth and form (GF) and the other selected for high wood density as well as growth and form (HD), were replicated on two low-altitude New Zealand sites: Tarawera (pumice soil, 38°08′S) and Woodhill (coastal dune, 36°42′S). The GF material comprised 33 pair-crosses (19 parents) × 10 clones, and the HD material comprised 19 single-pair crosses (35 parents) × 10 clones, with six ramets per clone per site. Diameter (DBH), two tree-form variables, and needle retention (NRA) were assessed 8 years after planting, and wood density (DEN), acoustic velocity, and collapse were assessed 9 years after planting. The site differences were generally expressed more strongly in the GF population. Estimated genetic parameters were mostly similar for the two breeds, except that genotypic correlation between DBH and DEN was apparently zero in the HD population. Estimated broad-sense heritabilities (H2) were generally markedly higher than narrow-sense heritability estimates (h2), except with DEN. Estimated between-site type-B clonal genotypic correlations were generally high (>0.8) for wood properties. Overall, DBH showed adverse genetic correlations with wood properties. The Elite/Breed strategy appeared to be helpful in combating adverse genetic correlations.

Wood quality in artificially inclined 1-year-old trees of Eucalyptus regnans — differences in tension wood and opposite wood properties

2011 ◽  
Vol 41 (5) ◽  
pp. 930-937 ◽  
Author(s):  
Shakti S. Chauhan ◽  
John C.F. Walker
Keyword(s):  
Tension Wood ◽  
Wood Quality ◽  
Basic Density ◽  
Wood Properties ◽  
Acoustic Velocity ◽  
Volumetric Shrinkage ◽  
Longitudinal Shrinkage ◽  
Eucalyptus Regnans ◽  
New Approach ◽  
Opposite Wood

This paper presents a new approach to assess wood quality in 1-year-old Eucalyptus regnans F. Muell. Twenty-two seedlings were grown tilted to induce tension wood and acoustic velocity, basic density, longitudinal shrinkage, and volumetric shrinkage of both opposite wood and tension wood were assessed subsequently. Longitudinal growth strains were also estimated in the leaning stems by sawing along the length through the pith and measuring the bending of the two halves. The derived longitudinal growth strain, which varied from 708 to 2319 µε, was uncorrelated with stem and wood characteristics. Wood characteristics differed significantly between upper-side wood (predominantly tension wood) and lower-side wood (opposite wood). Tension wood was characterized by a higher acoustic velocity (high stiffness), basic density, and volumetric shrinkage compared with opposite wood. Tension wood also exhibited significant collapse and dimensional distortion such as twisting. Longitudinal shrinkage exhibited a significant negative relationship with acoustic velocity in opposite wood and a positive relationship with the basic density in tension wood. This new approach has potential in early selection of breeding material with superior normal wood properties from 1-year-old material by isolating the influence of tension wood. This approach can also be useful in understanding the variability in propensity of tension wood production in breeding populations.

scholarly journals Estimating solid wood properties using Pilodyn and acoustic velocity on standing trees of Norway spruce

2015 ◽  
Vol 72 (4) ◽  
pp. 499-508 ◽  
Author(s):  
Zhi-Qiang Chen ◽  
Bo Karlsson ◽  
Sven-Olof Lundqvist ◽  
María Rosario García Gil ◽  
Lars Olsson ◽  
...  
Keyword(s):  
Norway Spruce ◽  
Wood Properties ◽  
Solid Wood ◽  
Acoustic Velocity ◽  
Standing Trees

Genetic analysis of wood quality traits in Norway spruce open-pollinated progenies and their parent plus trees at clonal archives and the evaluation of phenotypic selection of plus trees

2019 ◽  
Vol 49 (7) ◽  
pp. 810-818 ◽  
Author(s):  
Linghua Zhou ◽  
Zhiqiang Chen ◽  
Sven-Olof Lundqvist ◽  
Lars Olsson ◽  
Thomas Grahn ◽  
...  
Keyword(s):  
Norway Spruce ◽  
Wood Density ◽  
Wood Quality ◽  
Microfibril Angle ◽  
Phenotypic Selection ◽  
Wood Properties ◽  
Narrow Sense Heritability ◽  
Pilodyn Penetration ◽  
Plus Tree ◽  
Selection Of

A two-generation pedigree involving 519 Norway spruce (Picea abies (L.) Karst.) plus trees (at clonal archives) and their open-pollinated (OP) progenies was studied with the aim to evaluate the potential of plus-tree selection based on phenotype data scored on the plus trees. Two wood properties (wood density and modulus of elasticity, MOE) and one fiber property (microfibril angle, MFA) were measured with a SilviScan instrument on samples from one ramet per plus tree and 12 OP progenies per plus tree (total of 6288 trees). Three ramets per plus tree and their OP progenies were also assessed for Pilodyn penetration depth and Hitman acoustic velocity, which were used to estimate MOE. The narrow-sense heritability (h2) estimates based on parent–offspring regression were marginally higher than those based on half-sib correlation when three ramets per plus tree were included. For SilviScan data, estimates of the correlation between half-sib, progeny-based breeding values (BVs) and plus-tree phenotypes, as well as repeatability estimates, were highest for wood density, followed by MOE and MFA. Considering that the repeatability estimates from the clonal archive trees were higher than any h2 estimate, selection of the best clones from clonal archives would be an effective alternative.

Impact of the foliar pathogen Swiss needle cast on wood quality of Douglas-fir

2005 ◽  
Vol 35 (2) ◽  
pp. 331-339 ◽  
Author(s):  
G R Johnson ◽  
Amy T Grotta ◽  
Barbara L Gartner ◽  
Geoff Downes
Keyword(s):  
Moisture Content ◽  
Wood Density ◽  
Wood Quality ◽  
Ring Width ◽  
Wood Properties ◽  
Douglas Fir ◽  
Needle Cast ◽  
Needle Retention ◽  
Foliar Pathogen ◽  
Swiss Needle Cast

Many stands of Douglas-fir (Pseudotsuga menziesii (Mirb.) Franco) near coastal areas of Oregon and Washington are heavily infected with the foliar pathogen causing Swiss needle cast (SNC) disease, and yet there is very little research on the resulting wood quality. Modulus of elasticity (MOE), modulus of rupture (MOR), microfibril angle (MFA), wood density, latewood proportion, and sapwood moisture content were examined in 20- to 28-year-old trees from 15 stands that were infected with varying intensities of SNC. SNC severity was quantified by measuring needle retention, the number of needle cohorts retained at three crown levels. Correlations between disease severity and wood properties were examined at both the stand and within-stand levels. Trees from heavily infected stands (needle retention <2 years) had higher MOE, wood density, and latewood proportion and lower sapwood moisture content than trees from healthier stands. Breast-height age (BHage) was also correlated with these properties, but age alone did not explain all of the increases. MFA was not associated with SNC severity. Within stands, needle retention was not associated with MOE or MOR. The increase in latewood proportion in diseased stands appears to be the driving factor behind their increase in stiffness (MOE). Ring width decreased with decreased needle retention, and the examined wood properties generally showed stronger correlations with ring width than with needle retention.

scholarly journals Genetic Variation of Wood Density and Its Relationship with Drill Resistance in Shortleaf Pine

2008 ◽  
Vol 32 (3) ◽  
pp. 130-133 ◽  
Author(s):  
David Gwaze ◽  
Aaron Stevenson
Keyword(s):  
Wood Density ◽  
Wood Quality ◽  
Rapid Assessment ◽  
Tree Level ◽  
Quality Trait ◽  
Shortleaf Pine ◽  
Individual Tree ◽  
New Device ◽  
Standing Trees ◽  
The Individual

Abstract Wood density is an important wood quality trait, but inexpensive, reliable, and rapid methods for assessing it are lacking. A new device called the Resistograph has the potential for rapid assessment wood density of standing trees. The relationship between wood density and drill resistance measured by a Resistograph was investigated in a shortleaf pine (Pinus echinataMill.) population in Missouri at the age of 25 years. At the individual-tree level the linear relationship between wood density and drill resistance (amplitude) was weak and positive (R2= 0.23) but was stronger (R2 = 0.47) at the family mean level. Genetic relationship between the two traits was moderately strong (r A = 0.74). Individual-tree heritability estimates for both traits were high (h2 = 0.47 for wood density and h2 = 0.64 for amplitude). The efficiency of using the Resistograph to indirectly select for improvement of wood density was 86% at individual-tree level, suggesting that the Resistograph could reliably be used to assess wood density in live shortleaf pine trees.

Contribution to the automation of the calculations involving the forest inventory with the aid of an office computer

1970 ◽  
Vol 20 ◽  
Author(s):  
R. Goossens
Keyword(s):  
Tree Species ◽  
Forest Inventory ◽  
Basal Area ◽  
Annual Increment ◽  
Mixed Stands ◽  
Mean Values ◽  
Standing Trees ◽  
General Program ◽  
Magnetic Card ◽  
The Right

Contribution to the automation of the calculations involving  the forest inventory with the aid of an office computer - In this contribution an attempt was made to perform the  calculations involving the forest inventory by means of an office computer  Olivetti P203.     The general program (flowchart 1), identical for all tree species except  for the values of the different parameters, occupies the tracks A and B of a  magnetic card used with this computer. For each tree species one magnetic  card is required, while some supplementary cards are used for the  subroutines. The first subroutine (flowchart 1) enables us to preserve  temporarily the subtotals between two tree species (mixed stands) and so  called special or stand cards (SC). After the last tree species the totals  per ha are calculated and printed on the former, the average trees occuring  on the line below. Appendix 1 gives an example of a similar form resulting  from calculations involving a sampling in a mixed stand consisting of Oak  (code 11), Red oak (code 12), Japanese larch (code 24) and Beech (code 13).  On this form we find from the left to the right: the diameter class (m), the  number of trees per ha, the basal area (m2/ha), the current annual increment  of the basal area (m2/year/ha), current annual volume increment (m3/year/ha),  the volume (m3/ha) and the money value of the standing trees (Bfr/ha). On the  line before the last, the totals of the quantities mentioned above and of all  the tree species together are to be found. The last line gives a survey of  the average values dg, g, ig, ig, v and w.     Besides this form each stand or plot has a so-called 'stand card SC' on  wich the totals cited above as well as the area of the stand or the plot and  its code are stored. Similar 'stand card' may replace in many cases  completely the classical index cards; moreover they have the advantage that  the data can be entered directly into the computer so that further  calculations, classifications or tabling can be carried out by means of an  appropriate program or subroutine. The subroutine 2 (flowchart 2) illustrates  the use of similar cards for a series of stands or eventually a complete  forest, the real values of the different quantities above are calculated and  tabled (taking into account the area). At the same time the general totals  and the general mean values per ha, as well as the average trees are  calculated and printed. Appendix 2 represents a form resulting from such  calculations by means of subroutine 2.

scholarly journals EXPRESS: Chronic thromboembolic pulmonary hypertension following pulmonary embolism with a right ventricular thrombus: A report of two cases

2021 ◽  
pp. 204589402110136
Author(s):  
Tailong Zhang ◽  
Weitao Liang ◽  
Longrong Bian ◽  
Zhong Wu
Keyword(s):  
Pulmonary Hypertension ◽  
Right Ventricular ◽  
Chronic Thromboembolic Pulmonary Hypertension ◽  
Imaging Features ◽  
Pulmonary Endarterectomy ◽  
Right Heart ◽  
Thromboembolic Pulmonary Hypertension ◽  
The Right ◽  
Cardiac Masses

Right heart thrombus (RHT) accompanied by chronic thromboembolic pulmonary hypertension (CTEPH) is a rare entity. RHT may develop in the peripheral veins or in situ within the right heart chambers. The diagnosis of RHT is challenging, since its symptoms are typically non-specific and its imaging features resemble those of cardiac masses. Here, we report two cases of RHT with CTEPH that presented as right ventricular masses initially. Both patients underwent simultaneous pulmonary endarterectomy (PEA) and resection of the ventricular thrombi. Thus, when mass-like features are confirmed by imaging, RHT should be suspected in patients with CTEPH, and simultaneous RHT resection is required along with PEA.

A Neo-Assyrian statue from Til Barsib

Iraq ◽  
1996 ◽  
Vol 58 ◽  
pp. 79-87
Author(s):  
Arlette Roobaert
Keyword(s):  
Iron Age ◽  
Lower Portion ◽  
Maximum Height ◽  
Clear Indication ◽  
Large Hole ◽  
Relative Placement ◽  
The Right ◽  
As If ◽  
Medium Texture

During the 1993 season of excavations at Tell Ahmar, three pieces of a life-size basalt statue were found in a pit dug into one of the large walls surrounding an Iron Age vaulted tomb (Fig. 1). The head, the tors o and the lower part fitted together perfectly. When correctly assembled, these three pieces formed the figure of a standing beardless man with clasped hands (Fig. 2a−b). Only the feet were missing. The maximum height of the reconstructed statue is 1.45m. It was clear from the damage to portions of its body that the statue had been deliberately broken in antiquity. Details, such as a large hole on the right side of the chest, a smaller one on the top of the head and, above all, the defacement of the head suggest that the statue may have actually been “killed”.All three pieces of the statue, which was carved out of a blue greyish basalt of medium texture, were found lying on their backs (Fig. 4). The head lay next to the lower part of the statue, but was buried in a slightly deeper position. The relative placement of these fragments seems to be a clear indication that the statue was not knocked down at this particular spot, but was brought to this location in separate pieces, perhaps with the deliberate intention of burying them.The head was cut off as if the statue had been decapitated. The torso was separated from the lower portion of the statue by an oblique cut that divided the figure just below the waist. The cut runs downwards from the back and continues underneath the clasped hands at the front, leaving the hands almost completely undamaged. The lower part of the statue seems to have been separated from the missing feet by a horizontal cut. This may indicate that the base of the statue was left in situ, probably because it was solidly set in the ground.

Sign in / Sign up

Export Citation Format

Share Document