Electromechanical fields in a hollow piezoelectric cylinder under non-uniform load: flexoelectric effect

The relations of a local gradient non-ferromagnetic electroelastic continuum are used to solve the problem of an axisymmetrical loaded hollow cylinder. Analytical solutions are obtained for tetragonal piezoelectric materials of point group 4 mm for two cases of external loads applied to the body surfaces. Namely, the hollow pressurized cylinder and a cylinder subjected to an electrical voltage V across its thickness are considered. The derived solutions demonstrate that the non-uniform electric load causes a mechanical deformation of piezoelectric body, and vice versa, the inhomogeneous radial pressure of the cylinder induces its polarization. Such a result is obtained due to coupling between the electromechanical fields and a local mass displacement being considered. In the local gradient theory, the local mass displacement is associated with the changes to a material’s microstructure. The classical theory does not consider the effect of material microstructure on the behavior of solid bodies and is incapable of explaining the mentioned phenomena. It is also shown that the local gradient theory describes the size-dependent properties of piezoelectric nanocylinders. Analytical solutions to the formulated boundary-value problems can be used in conjunction with experimental data to estimate some higher-order material constants of the local gradient piezoelectricity. The obtained results may be useful for a wide range of appliances that utilize small-scale piezoelectric elements as constituting blocks.

Liquid distribution and its effect on local mass transfer in a packed column of Pall rings

The spatial variations of liquid distribution and local mass transfer coefficient in a 0.30-m column of 25.4-m Pall rings were investigated. The data of liquid distribution was collected with a 39-cell liquid collector and a wall-flow tube from a doubled-wall section in the column at the packing-support level. The local mass transfer coefficients were measured via the electrochemical technique by individual cathodic nickel-coated Pall rings placed at various spatial positions. Both measurements were conducted at various fluid flow rates with three liquid distributor designs at different bed heights. Liquid distribution and local mass transfer coefficients observed were far from uniform in the column. The wall flow developed along the packed bed until a fully developed flow pattern was reached. With more uniform initial liquid distribution, the less packing height needed to reach the fully developed flow pattern along with higher the mass transfer efficiency in the column. Ladder-type liquid distributor (LLD) showed less angular effect in measurements. Increasing the liquid flow rate slightly improved the uniformity of liquid distribution and enhanced the mass transfer. No influence of gas flow rate on liquid distribution and mass transfer coefficient was found at the range of gas flow rates used. These gas flow rates were much lower than the loading point. Liquid maldistribution factor and mass transfer maldistribution factor decreased with increases in the uniformity of the initial liquid distribution. These values were 0.21(0.48). 0.16(0.26) and 0.14(0.22) for single-point liquid distributor (SPLD), cross-type liquid distributor (CLD) and LLD, respectively. By comparison, a good agreement was observed on the relation of liquid maldistribution factor and mass transfer maldistribution factor.

Liquid distribution and its effect on local mass transfer in a packed column of Pall rings

The spatial variations of liquid distribution and local mass transfer coefficient in a 0.30-m column of 25.4-m Pall rings were investigated. The data of liquid distribution was collected with a 39-cell liquid collector and a wall-flow tube from a doubled-wall section in the column at the packing-support level. The local mass transfer coefficients were measured via the electrochemical technique by individual cathodic nickel-coated Pall rings placed at various spatial positions. Both measurements were conducted at various fluid flow rates with three liquid distributor designs at different bed heights. Liquid distribution and local mass transfer coefficients observed were far from uniform in the column. The wall flow developed along the packed bed until a fully developed flow pattern was reached. With more uniform initial liquid distribution, the less packing height needed to reach the fully developed flow pattern along with higher the mass transfer efficiency in the column. Ladder-type liquid distributor (LLD) showed less angular effect in measurements. Increasing the liquid flow rate slightly improved the uniformity of liquid distribution and enhanced the mass transfer. No influence of gas flow rate on liquid distribution and mass transfer coefficient was found at the range of gas flow rates used. These gas flow rates were much lower than the loading point. Liquid maldistribution factor and mass transfer maldistribution factor decreased with increases in the uniformity of the initial liquid distribution. These values were 0.21(0.48). 0.16(0.26) and 0.14(0.22) for single-point liquid distributor (SPLD), cross-type liquid distributor (CLD) and LLD, respectively. By comparison, a good agreement was observed on the relation of liquid maldistribution factor and mass transfer maldistribution factor.

Paediatric neurosurgical implications of a ribosomopathy: illustrative case and literature review

Ribosomopathies are rare, recently defined entities. One of these, Labrune syndrome, is recognisable radiologically by its distinctive triad of leukoencephalopathy, intracranial calcifications and cysts (LCC). These cysts may have neurosurgical implications at different ages because of their progressive expansion and local mass effect. The aetiology of LCC is related to a widespread cerebral microangiopathy and is due to a genetic mutation in SNORD118, responsible for stabilisation of the large ribosomal subunit during assembly.

Residual np-interaction and mass predictions in transfermium region

We study the consistency of local mass relation approach in its application to prediction of nuclear masses in the region of superheavy elements. Binding energy calculations are carried out for nuclei with [Formula: see text] using formulas for evaluation of residual [Formula: see text]-interaction. The results are found to be in good agreement with the experimental data AME2016. We also make predictions for characteristics of [Formula: see text]-decay in isotopes [Formula: see text]–106, [Formula: see text]–157.

Sensitivity factors of aircraft mass for the conceptual design

Purpose The purpose of this work is to further develop the methodology for calculating the aircraft take-off mass and its main functional components for the conceptual analysis and synthesis of new projects. Design/methodology/approach The method is based on the assessment of changes in the take-off gross mass (TOGM) of the already developed project or already existing a basic version of the aircraft when making local mass changes for its modification or for the numerical researches to create a more advanced project. The method is based on the “sensitivity factors of mass” (SFM) of aircraft, which represents the ratio of TOGM to initial (local) mass changes of its main functional components. The method of analytical refined calculation of SFM for the initial mass change and the main aerodynamic characteristics is given. Findings In comparison with the long-known method based on weight (mass) growth factors, which were considered constant, this method takes into account the dependence from the value of the initial local mass change and its functional purpose. Practical implications This method allows the designer to calculate more strictly the final changes in the TOGM on the initial stages of conceptual design when finding new project solutions. Numerical calculations are given on the example of passenger aircraft. The dependence of SFM and TOGM and its functional masses on the value of the initial change of the structure mass are shown. This method is used in the educational process at the college of Aerospace Engineering in the Aircraft Design department. Originality/value The considered method based on SFM is simple and convenient and more accurate for conducting project research on many project parameters when analyzing and synthesizing a new project.