Slippage during high-pressure torsion of commercially pure titanium and application of accumulative HPT to it

A new efficient method was used to find that in the case of high-pressure torsion of commercially pure titanium, accumulation of shear strain in Ti does not occur due to slippage of anvils. Despite this, micro-hardness increases as the number of turns n increases, and Ti structure is refined more intensively. High-pressure torsion is accompanied by a high-pressure ω-phase formation. However, the content of ω-phase changes non-monotonously with an increase in the number of turns. First, while number of turns is less than n=5, the ω-phase content reaches 50%. Upon further deformation, the ω-phase content decreases to 15% for n=20. A new accumulative high-pressure torsion method is applied to commercially pure titanium for the first time. Accumulative high-pressure torsion leads to the strongest transformation of the structure and an increase in hardness, since stronger real deformation occurs due to composition of compression and torsion strain cycles.

Metal allergy hypersensitivity after posterior thoracic spinal fusion: A case report and review of the literature

Background: Spine surgeons rarely consider metal allergies when placing hardware, as implants are thought to be inert. Case Description: A 32-year-old male presented with a skin rash attributed to the trace metal in his spinal fusion instrumentation. Patch testing revealed sensitivities to cobalt, manganese, and chromium. He underwent hardware removal and replacement with constructs of commercially pure titanium. His skin findings resolved at 2 weeks after surgery and were stable at 6 weeks. Conclusion: Hypersensitivity to metal (i.e., metal allergy) should be considered before performing instrumented spinal fusions.

Improvement of Mechanical and Corrosion Properties of Commercially Pure Titanium Using Alumina PEO Coatings

In this study, the surface of commercially pure titanium (Cp-Ti) was covered by a 21–95 µm-thick aluminum oxide layer using plasma electrolytic oxidation. Coating characterization revealed the formation of nodular and granular α- and γ-Al2O3 phases with minor amounts of TiAl2O5 and Na2Ti4O9 which yielded a maximum 49.0 GPa hardness and 50 N adhesive critical load. The corrosion resistance behavior in 3.5 wt.% NaCl solution of all plasma electrolytic oxidation (PEO) coatings was found to be two orders of magnitude higher compared to bare Ti substrate.

Effect of the Processing Parameters on the Porosity and Mechanical Behavior of Titanium Samples with Bimodal Microstructure Produced via Hot Pressing

Commercially pure (c.p.) titanium grade IV with a bimodal microstructure is a promising material for biomedical implants. The influence of the processing parameters on the physical, microstructural, and mechanical properties was investigated. The bimodal microstructure was achieved from the blends of powder particles with different sizes, while the porous structure was obtained using the space-holder technique (50 vol.% of ammonium bicarbonate). Mechanically milled powders (10 and 20 h) were mixed in 50 wt.% or 75 wt.% with c.p. titanium. Four different mixtures of powders were precompacted via uniaxial cold pressing at 400 MPa. Then, the specimens were sintered at 750 °C via hot pressing in an argon gas atmosphere. The presence of a bimodal microstructure, comprised of small-grain regions separated by coarse-grain ones, was confirmed by optical and scanning electron microscopies. The samples with a bimodal microstructure exhibited an increase in the porosity compared with the commercially available pure Ti. In addition, the hardness was increased while the Young’s modulus was decreased in the specimens with 75 wt.% of the milled powders (20 h).

A Tribological and Ion Released Research of Ti-Materials for Medical Devices

The increase in longevity worldwide has intensified the use of different types of prostheses for the human body, such as those used in dental work as well as in hip and knee replacements. Currently, Ti-6Al-4V is widely used as a joint implant due to its good mechanical properties and durability. However, studies have revealed that this alloy can release metal ions or particles harmful to human health. The mechanisms are not well understood yet and may involve wear and/or corrosion. Therefore, in this work, commercial pure titanium and a Ti-6Al-4V alloy were investigated before and after being exposed to a simulated biological fluid through tribological tests, surface analysis, and ionic dissolution characterization by ICP-AES. Before exposure, X-ray diffraction and optical microscopy revealed equiaxed α-Ti in both materials and β-Ti in Ti-6Al-4V. Scratch tests exhibited a lower coefficient of friction for Ti-6Al-4V alloy than commercially pure titanium. After exposure, X-ray photoelectron spectroscopy and surface-enhanced Raman spectroscopy results showed an oxide film formed by TiO2, both in commercially pure titanium and in Ti-6Al-4V, and by TiO and Al2O3 associated with the presence of the alloys. Furthermore, inductively coupled plasma atomic emission spectroscopy revealed that aluminum was the main ion released for Ti-6Al-4V, giving negligible values for the other metal ions.