propagation direction
Recently Published Documents


TOTAL DOCUMENTS

472
(FIVE YEARS 106)

H-INDEX

32
(FIVE YEARS 5)

Micromachines ◽  
2021 ◽  
Vol 13 (1) ◽  
pp. 40
Author(s):  
Hongrui Lv ◽  
Yinglong Huang ◽  
Yujie Ai ◽  
Zhe Liu ◽  
Defeng Lin ◽  
...  

The impact of device parameters, including AlN film thickness (hAlN), number of interdigital transducers (NIDT), and acoustic propagation direction, on the performance of c-plane AlN/sapphire-based SAW temperature sensors with an acoustic wavelength (λ) of 8 μm, was investigated. The results showed that resonant frequency (fr) decreased linearly, the quality factor (Q) decreased and the electromechanical coupling coefficient (Kt2) increased for all the sensors with temperature increasing from −50 to 250 °C. The temperature coefficients of frequency (TCFs) of sensors on AlN films with thicknesses of 0.8 and 1.2 μm were −65.57 and −62.49 ppm/°C, respectively, indicating that a reduction in hAlN/λ favored the improvement of TCF. The acoustic propagation direction and NIDT did not obviously impact the TCF of sensors, but they significantly influenced the Q and Kt2 of the sensors. At all temperatures measured, sensors along the a-direction exhibited higher fr, Q and Kt2 than those along the m-direction, and sensors with NIDT of 300 showed higher Q and Kt2 values than those with NIDT of 100 and 180. Moreover, the elastic stiffness of AlN was extracted by fitting coupling of modes (COM) model simulation to the experimental results of sensors along different directions considering Euler transformation of material parameter-tensors. The higher fr of the sensor along the a-direction than that along the m-direction can be attributed to its larger elastic stiffness c11, c22, c44, and c55 values.


2021 ◽  
Author(s):  
Rakesh Das ◽  
Shmuel Gershon ◽  
Benny Bar-On ◽  
Maryam Tadayon ◽  
Amir Ayali ◽  
...  

The female locust has a unique mechanism for digging in order to deposit its eggs deep in the ground. It utilizes two pairs of sclerotized valves to displace the granular matter, while extending its abdomen as it propagates underground. This ensures optimal conditions for the eggs to incubate, and provides them with protection from predators. Here, two major axes of operation of the digging valves are identified, one in parallel to the propagation direction of the ovipositor, and one perpendicular to it. The direction-dependent biomechanics of the locust major, dorsal digging valves are quantified and analyzed, under forces in the physiological range and beyond, considering hydration level, as well as the females age, or sexual maturation state. Our findings reveal that the responses of the valves to compression forces in the specific directions change upon sexual maturation to follow their function, and depend on environmental conditions. Namely, in the physiological force range, the valves are resistant to mechanical failure. In addition, mature females, which lay eggs, have stiffer valves, up to roughly nineteen times the stiffness of the pre-mature locusts. The valves are stiffer in the major working direction, corresponding to soil shuffling and compression, compared to the direction of propagation. Hydration of the valves reduces their stiffness but increases their resilience against failure. These findings provide mechanical and materials guidelines for the design of novel non-drilling excavating tools, including 3D-printed anisotropic materials based on composites.


Author(s):  
Takashi Manago ◽  
Kanta Fujii ◽  
Kenji Kasahara ◽  
Kazuyuki Nakayama

Abstract The characteristics of spin waves propagating in Fibonacci magnonic quasi-crystals (MQCs) were investigated in micromagnetic simulations. The spin waves feel 1/3rd of the characteristic Fibonacci sequence length as a period, and mini band gaps reflected by MQCs are formed. The effect of the MQC on the spin wave’s propagation becomes prominent above the first band gap frequency. The properties of spin waves in MQCs generally depend on the propagation direction, because spin waves feel different structures depending on the direction. Therefore, the nonreciprocity (NR) characteristics becomes complex. The NR characteristics change at every band gap frequency and hence across the frequency regions defined by them. In particular, some frequency regions have almost no NR, while others have enhanced NR and some have even negative NR. These characteristics provide a new way to control NR.


2021 ◽  
Vol 2131 (5) ◽  
pp. 052098
Author(s):  
R M Taziev

Abstract In this study, the surface acoustic wave (SAW) temperature properties in flux-grown α-GeO2 crystal are numerically investigated. It is shown that the SAW velocity temperature change substantially depends only on the temperature coefficient of three elastic constants: C66, C44 and C14 for crystal cuts and wave propagation directions, where SAW has high electromechanical coupling coefficient. The SAW temperature coefficient of delay (TCD) for these crystal cuts are in the range from -40 ppm /°C to -70 ppm /°C. In contrast to alpha-quartz, the surface wave TCD values are not equal to zero in Z-, Y- , and Z- rotated cuts of α-GeO2 single crystal. Its values are comparable in the magnitude with the surface wave TCD values in lithium tantalate. In the crystal grown from the melt, the interdigital transducer (IDT) conductance has two times larger amplitude than that in hydrothermally grown a-GeO2. The leaky acoustic wave excited by IDT on Z+120°-cut and wave propagation direction along the X-axis, has an electromechanical coupling coefficient 5 times less than that for surface wave.


2021 ◽  
Vol 2131 (5) ◽  
pp. 052099
Author(s):  
R M Taziev

Abstract The success on the growth of new piezoelectric materials allows sufficiently increase the operating temperature of the surface acoustic wave (SAW) devices from 300°C to 1000°C. A new calcium yttrium aluminate (CaYAl3O7) single crystal of the tetragonal symmetry has piezoelectric properties up to the temperature of 1000°C. The paper presents a numerical study of the surface acoustic wave properties in the crystal. The SAW velocity, electromechanical coupling coefficient and power flow angle are studied for different crystal cuts of CaYAl3O7. It is shown that the maximum value of SAW coupling coefficient (0.24%) is on the Z+60°-cut and wave propagation direction along the X-axis of the crystal. For the Z-cut and wave propagation direction along the X+45°-axis of crystal, the SAW coupling coefficient is equal to 0.2%. These two cuts of the crystal are potentially useful for SAW device applications.


Nanophotonics ◽  
2021 ◽  
Vol 0 (0) ◽  
Author(s):  
John Pendry ◽  
Paloma Huidobro ◽  
Mario Silveirinha ◽  
Emanuele Galiffi

Abstract We ask the question “what happens to Bloch waves in gratings synthetically moving at near the speed of light?”. First we define a constant refractive index (CRI) model in which Bloch waves remain well defined as they break the light barrier, then show their dispersion rotating through 360° from negative to positive and back again. Next we introduce the effective medium approximation (EMA) then refine it into a 4-wave model which proves to be highly accurate. Finally using the Bloch waves to expand a pulse of light we demonstrate sudden inflation of pulse amplitude combined with reversal of propagation direction as a luminal grating is turned on.


2021 ◽  
Vol 11 (1) ◽  
Author(s):  
M. Mosleh ◽  
M. Ranjbaran ◽  
S. M. Hamidi

AbstractVarious efforts have been made to determine the polarization state of evanescent waves in different structures. The present study shows the reliability of magneto-optical spectroscopy of D1 and D2 lines of rubidium metal and polarization-dependent transitions to investigate and trace the changes in the polarization state of evanescent fields during total internal reflection over different angles. For this purpose, we design and fabricate atomic- evanescent Rb vapor cells and examine the effect of polarization changes of evanescent waves, depending on the propagation direction of evanescent waves in anisotropic rubidium vapor media under 88 mT external magnetic field by different configurations theoretically and experimentally. The results confirm the dependency of allowed $$\sigma^{ \pm } { }\;{\text{and}}\;\pi$$ σ ± and π transitions on the magneto optical configuration as a tool to determine changes in the polarization of evanescent waves in more complicated wave states in anisotropic media.


Solar Physics ◽  
2021 ◽  
Vol 296 (11) ◽  
Author(s):  
Y. I. Egorov ◽  
V. G. Fainshtein

2021 ◽  
Vol 2015 (1) ◽  
pp. 012008
Author(s):  
Syuzanna Asadulina ◽  
Andrey Bogdanov ◽  
Stanislav Glybovski ◽  
Oleh Yermakov

Abstract We analyze the TE-TM polarization degeneracy of the guided modes of a dielectric metasurface in the microwave frequency range. We find the optimum metasurface design and investigate the dependence of the degeneracy degree on the propagation direction. Finally, we simulate the possible microwave experiment demonstrating the extraction of isofrequency contours for this metasurface. The results obtained could be useful for flat photonic devices with the function of polarization control.


Sign in / Sign up

Export Citation Format

Share Document