Composite Slow-Release Fouling Release Coating Inspired by Synergistic Anti-Fouling Effect of Scaly Fish

Inspired by the antifouling properties of scaly fish, the conventional silicone coating with phenylmethylsilicone oil (PSO/PDMS) composite coating was fabricated and modified with single layer polystyrene (PS) microsphere (PSO/PDMS-PS) arrays. The fish scale like micro-nano structures were fabricated on the surface of bio-inspired coating, which can reduce the contact area with the secreted protein membrane of fouling organisms effectively and prevent further adhesion between fouling organisms and bio-inspired coating. Meanwhile, PSO exuded to the coating surface has the similar function with mucus secreted by fish epidermis, which make the coating surface slithery and will be polished with the fouling organisms in turbulent waters. Compared to PSO/PDMS coating without any structure and conventional silicone coating, PSO/PDMS-PS showed better antiadhesion activity against both marine bacteria and benthic diatom (Navicula sp.). Additionally, the existence of PS microspheres can reduce the release rate of PSO greatly, which will extend the service life of coating. Compared to PSO/PDMS coating, the sustained release efficiency of PSO/PDMS-PS coating can reach 23.2%. This facile method for fabricating the bio-inspired composite slow-release antifouling coating shows a widely fabricating path for the development of synergistic anti-fouling coating.

Numerical Evaluation on Residual Thermal Stress-Induced Delamination at PDMS–Metal Interface of Neural Prostheses

The most common failure mode of implantable neural implants has been delamination of layers in compound structures and encapsulations in a wet body environment. Current knowledge of failure mechanisms of adhesion and its standardized test procedures are lacking and must be established. This study demonstrated a combined experimental and numerical method to investigate the residual stresses from one of the most common encapsulation materials, silicone rubber (polydimethylsiloxane-PDMS) during the coating process at elevated temperatures. Measured shrinkage of test specimen correlates well to a modified shrinkage model using thermal-mechanical finite element method (FEM) simulation. All simulated interfacial stresses show stress concentration at the PDMS coating front depending on curing temperature and coating thickness, while Griffith’s condition estimated the delamination of the coating front. This study emphasizes the understanding of the interfacial delamination giving the possibility to predict failure mode of neural interface.

Solvent-free, Ultrafast and Ultrathin PDMS Coating Triggered by Plasma for Molecule Separation and Releasing

In this work, we developed a facile, ultrafast, and solvent-free polydimethylsiloxane (PDMS) coating method triggered by plasma for ultrathin coating on various nanostructured substrates at room temperature. During plasma treatment,...

Experimental Validation of the Attenuation Properties in the Sonic Range of Metaconcrete Containing Two Types of Resonant Inclusions

Background Metaconcrete is a new concept of concrete, showing marked attenuation properties under impact and blast loading, where traditional aggregates are partially replaced by resonant bi-material inclusions. In a departure from conventional mechanical metamaterials, the inclusions are dispersed randomly as cast in the material. The behavior of metaconcrete at supersonic frequencies has been investigated theoretically and numerically and confirmed experimentally. Objective The feasibility of metaconcrete to achieve wave attenuation at low frequencies demands further experimental validation. The present study is directed at characterizing dynamically, in the range of the low sonic frequencies, the—possibly synergistic—effect of combinations of different types of inclusions on the attenuation properties of metaconcrete. Methods Dynamic tests are conducted on cylindrical metaconcrete specimens cast with two types of spherical inclusions, made of a steel core and a polymeric coating. The two inclusions differ in terms of size and coating material: type 1 inclusions are 22 mm diameter with 1.35 mm PDMS coating; type 2 inclusions are 24 mm diameter with 2 mm layer natural rubber coating. Linear frequency sweeps in the low sonic range (< 10 kHz), tuned to numerically estimated inclusion eigenfrequencies, are applied to the specimens through a mechanical actuator. The transmitted waves are recorded by transducers and Fast-Fourier transformed (FFT) to bring the attenuation spectrum of the material into full display. Results Amplitude reductions of transmitted signals are markedly visible for any metaconcrete specimens in the range of the inclusion resonant frequencies, namely, 3,400-3,500 Hz for the PDMS coating inclusions and near 3,200 Hz for the natural rubber coating inclusions. Specimens with mixed inclusions provide a rather uniform attenuation in a limited range of frequencies, independently of the inclusion density, while specimens with a single inclusion type are effective over larger frequency ranges. With respect to conventional concrete, metaconcrete reduces up to 90% the amplitude of the transmitted signal within the attenuation bands. Conclusions Relative to conventional concrete, metaconcrete strongly attenuates waves over frequency bands determined by the resonant frequencies of the inclusions. The present dynamical tests conducted in the sonic range of frequencies quantify the attenuation properties of the metaconcrete cast with two types inclusions, providing location, range and intensity of the attenuation bands, which are dependent on the physical-geometric features of the inclusions.

Poly (Dimethylsiloxane) Coating for Repellency of Polar and Non-Polar Liquids

The wettability of poly (dimethylsiloxane) (PDMS) coating on plasma-treated glass was studied at room temperature using polar and non-polar liquids. The wettability was investigated regarding the liquids’ surface tensions (STs), dielectric constants (DCs) and solubility parameters (SPs). For polar liquids, the contact angle (CA) and contact angle hysteresis (CAH) are controlled by the DCs and non-polar liquids by the liquids’ STs. Solubility parameter difference between the PDMS and the liquids demonstrated that non-polar liquids possessed lower CAH. An empirical model that integrates the interfacial properties of liquid/PDMS has been composed. Accordingly, the difference between the SPs of PDMS and the liquid is the decisive factor affecting CAH, followed by the differences in DCs and STs. Moreover, the interaction between the DCs and the SPs is of importance to minimize CAH. It has been concluded that CAH, and not CA, is the decisive attribute for liquid repellency of PDMS coating.