Axial Deformation Member

Keyword(s):  
2021 ◽  
Vol 6 (6) ◽  
pp. 83
Author(s):  
Angelo Aloisio

The estimate of internal prestressing in concrete beams is essential for the assessment of their structural reliability. Many scholars have tackled multiple and diverse methods to estimate the measurable effects of prestressing. Among them, many experimented with dynamics-based techniques; however, these clash with the theoretical independence of the natural frequencies of the forces of internally prestressed beams. This paper examines the feasibility of a hybrid approach based on dynamic identification and the knowledge of the elastic modulus. Specifically, the author considered the effect of the axial deformation on the beam length and the weight per unit of volume. It is questioned whether the uncertainties related to the estimate of the elastic modulus and the first natural frequency yield reasonable estimates of the internal prestressing. The experimental testing of a set of full-scale concrete girders with known design prestressing supports a discussion about its practicability. The author found that the uncertainty in estimating the natural frequencies and elastic modulus significantly undermines a reliable estimate of the prestressing state.


2021 ◽  
Vol 502 (2) ◽  
pp. 2266-2284
Author(s):  
Kazuo Makishima ◽  
Teruaki Enoto ◽  
Hiroki Yoneda ◽  
Hirokazu Odaka

ABSTRACT This paper describes an analysis of the NuSTAR data of the fastest-rotating magnetar 1E 1547 − 5408, acquired in 2016 April for a time lapse of 151 ks. The source was detected with a 1–60 keV flux of 1.7 × 10−11 erg s−1 cm−2, and its pulsation at a period of 2.086710(5) s. In 8–25 keV, the pulses were phase-modulated with a period of T = 36.0 ± 2.3 ks, and an amplitude of ∼0.2 s. This reconfirms the Suzaku discovery of the same effect at $T=36.0 ^{+4.5}_{-2.5}$ ks, made in the 2009 outburst. These results strengthen the view derived from the Suzaku data, that this magnetar performs free precession as a result of its axial deformation by ∼0.6 × 10−4, possibly caused by internal toroidal magneti fields (MFs) reaching ∼1016 G. Like in the Suzaku case, the modulation was not detected in energies below ∼8 keV. Above 10 keV, the pulse-phase behaviour, including the 36 ks modulation parameters, exhibited complex energy dependencies: at ∼22 keV, the modulation amplitude increased to ∼0.5 s, and the modulation phase changed by ∼65° over 10–27 keV, followed by a phase reversal. Although the pulse significance and pulsed fraction were originally very low in >10 keV, they both increased noticeably, when the arrival times of individual photons were corrected for these systematic pulse-phase variations. Possible origins of these complex phenomena are discussed, in terms of several physical processes that are specific to ultrastrong MFs.


2010 ◽  
Vol 97-101 ◽  
pp. 3910-3915
Author(s):  
Kun Cai

The deformation of single-walled carbon nanotubes (SWCNTs) under large axial strain is studied by a geometrical mapping method. The interactions between atoms in carbon nanotubes (CNTs) are described by Tersoff-Brenner potential. Results show the strain energy depends on chirality but hardly on tubes’ radii. For graphitic sheet under large axial deformation, the elastic moduli decrease with the increase of engineering strain under tension. The modulus reaches the peak value as the axial engineering strain reaches -0.08 for armchair pattern and -0.15 for zigzag pattern under compression.


1999 ◽  
Author(s):  
Vebil Yildirim ◽  
Erol Sancaktar ◽  
Erhan Kiral

Abstract This paper deals with the effect of the material types (Graphite-Epoxies and Kevlar-Epoxy) on the fundamental frequencies of uniaxial constant-pitch composite conical helical springs with solid circle section and fixed-fixed ends. The transfer matrix method is used for the determination of the fundamental natural frequencies. The rotary inertia, the shear and axial deformation effects are taken into account in the solution. The free vibrational charts for each material presented in this study cover the following vibrational parameters: n (number of active turns) = 5–10, α = (helix pitch angle) = 5° and 25°, R2/R1, (minimum to maximum radii of the cylinder) = 0.1 and 0.9, and Dmax/d (maximum cylinder to wire diameters) = 5 and 15. These charts can be used for the design of uniaxial composite conical springs.


Author(s):  
Chunxia Zhu ◽  
Jay Katupitiya ◽  
Jing Wang

Purpose Manipulator motion accuracy is a fundamental requirement for precision manufacturing equipment. Light weight manipulators in high speed motions are vulnerable to deformations. The purpose of this work is to analyze the effect of link deformation on the motion precision of parallel manipulators. Design/methodology/approach The flexible dynamics model of the links is first established by applying the Euler–Bernoulli beam theory and the assumed modal method. The rigid-flexible coupling equations of the parallel mechanism are further derived by using the Lagrange multiplier approach. The elastic energy resulting from spiral motion and link deformations are computed and analyzed. Motion errors of the 3-link torque-prismatic-torque parallel manipulator are then evaluated based on its inverse kinematics. The validation experiments are also conducted to verify the numerical results. Findings The lateral deformation and axial deformation are largest at the middle of the driven links. The axial deformation at the middle of the driven link is approximately one-tenth of the transversal deformation. However, the elastic potential energy of the transversal deformation is much smaller than the elastic force generated from axial deformation. Practical implications Knowledge on the relationship between link deformation and motion precision is useful in the design of parallel manipulators for high performing dynamic responses. Originality/value This work establishes the relationship between motion precision and the amount of link deformation in parallel manipulators.


2006 ◽  
Vol 128 (5) ◽  
pp. 555-567 ◽  
Author(s):  
Andrea Tonoli ◽  
Nicola Amati ◽  
Enrico Zenerino

Multiribbed serpentine belt drive systems are widely adopted in accessory drive automotive applications due to the better performances relative to the flat or V-belt drives. Nevertheless, they can generate unwanted noise and vibration which may affect the correct functionality and the fatigue life of the belt and of the other components of the transmission. The aim of the paper is to analyze the effect of the shear deflection in the rubber layer between the pulley and the belt fibers on the rotational dynamic behavior of the transmission. To this end the Firbank’s model has been extended to cover the case of small amplitude vibrations about mean rotational speeds. The model evidences that the shear deflection can be accounted for by an elastic term reacting to the torsional oscillations in series with a viscous term that dominates at constant speed. In addition, the axial deformation of the belt spans are taken into account. The numerical model has been validated by the comparison with the experimental results obtained on an accessory drive transmission including two pulleys and an automatic tensioner. The results show that the first rotational modes of the system are dominated by the shear deflection of the belt.


Sign in / Sign up

Export Citation Format

Share Document