Effect of operating conditions on Bromate Removal Efficiency in BAC filters

2002 ◽  
Vol 94 (4) ◽  
pp. 182-193 ◽  
Author(s):  
Mary Jo Kirisits ◽  
Vernon L. Snoeyink ◽  
Joanne C. Chee-Sanford ◽  
Becky J. Daugherty ◽  
Jess C. Brown ◽  
...  
Keyword(s):  
Removal Efficiency ◽  
Operating Conditions

Comparative Bio-sorption of Cadmium and Nickel Ions from Aqueous Solution onto Fibers of Date Palm using Fluidized Bed Column

2019 ◽  
Vol 70 (5) ◽  
pp. 1507-1512
Author(s):  
Baker M. Abod ◽  
Ramy Mohamed Jebir Al-Alawy ◽  
Firas Hashim Kamar ◽  
Gheorghe Nechifor
Keyword(s):  
Aqueous Solution ◽  
Heavy Metal ◽  
Metal Ions ◽  
Fluidized Bed ◽  
Removal Efficiency ◽  
Heavy Metal Ions ◽  
Date Palm ◽  
Operating Conditions ◽  
Initial Concentration ◽  
Bed Height

The aim of this study is to use the dry fibers of date palm as low-cost biosorbent for the removal of Cd(II), and Ni(II) ions from aqueous solution by fluidized bed column. The effects of many operating conditions such as superficial velocity, static bed height, and initial concentration on the removal efficiency of metal ions were investigated. FTIR analyses clarified that hydroxyl, amine and carboxyl groups could be very effective for bio-sorption of these heavy metal ions. SEM images showed that dry fibers of date palm have a high porosity and that metal ions can be trapped and sorbed into pores. The results show that a bed height of 6 cm, velocity of 1.1Umf and initial concentration for each heavy metal ions of 50 mg/L are most feasible and give high removal efficiency. The fluidized bed reactor was modeled using ideal plug flow and this model was solved numerically by utilizing the MATLAB software for fitting the measured breakthrough results. The breakthrough curves for metal ions gave the order of bio-sorption capacity as follow: Cd(II)]Ni(II).

scholarly journals Oxidative Extractive Desulfurization System for Fuel Oil Using Acidic Eutectic-Based Ionic Liquid

Processes ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 1050
Author(s):  
Sarrthesvaarni Rajasuriyan ◽  
Hayyiratul Fatimah Mohd Zaid ◽  
Mohd Faridzuan Majid ◽  
Raihan Mahirah Ramli ◽  
Khairulazhar Jumbri ◽  
...  
Keyword(s):  
Ionic Liquids ◽  
Removal Efficiency ◽  
Environmental Effects ◽  
Sulfur Compounds ◽  
Operating Conditions ◽  
Fuel Oil ◽  
Organosulfur Compounds ◽  
Dsc Analysis ◽  
Oil Refineries ◽  
Desulfurization Process

The biggest challenge faced in oil refineries is the removal of sulfur compounds in fuel oil. The sulfur compounds which are found in fuel oil such as gasoline and diesel, react with oxygen in the atmosphere to produce sulfur oxide (SOx) gases when combusted. These sulfur compounds produced from the reaction with oxygen in the atmosphere may result in various health problems and environmental effects. Hydrodesulfurization (HDS) is the conventional process used to remove sulfur compounds from fuel oil. However, the high operating conditions required for this process and its inefficiency in removing the organosulfur compounds turn to be the major drawbacks of this system. Researchers have also studied several alternatives to remove sulfur from fuel oil. The use of ionic liquids (ILs) has also drawn the interest of researchers to incorporate them in the desulfurization process. The environmental effects resulting from the use of these ILs can be eliminated using eutectic-based ionic liquids (EILs), which are known as greener solvents. In this research, a combination of extractive desulfurization (EDS) and oxidative desulfurization (ODS) using a photocatalyst and EIL was studied. The photocatalyst used is a pre-reported catalyst, Cu-Fe/TiO2 and the EIL were synthesized by mixing choline chloride (ChCl) with organic acids. The acids used for the EILs were propionic acid (PA) and p-toluenesulfonic acid (TSA). The EILs synthesized were characterized using thermogravimetry analyser (TGA) differential scanning calorimetry (DSC) analysis to determine the physical properties of the EILs. Based on the TGA analysis, ChCl (1): PA (3) obtained the highest thermal stability whereas, as for the DSC analysis, all synthesized EILs have a lower melting point than its pure component. Further evaluation on the best EIL for the desulfurization process was carried out in a photo-reactor under UV light in the presence of Cu-Fe/TiO2 photocatalyst and hydrogen peroxide (H2O2). Once the oxidation and extraction process were completed, the oil phase of the mixture was analyzed using high performance liquid chromatography (HPLC) to measure the sulfur removal efficiency. In terms of the desulfurization efficiency, the EIL of ChCl (1): TSA (2) showed a removal efficiency of about 99.07%.

Study on De-Nitrification of Improved Step-Feed Progress

2014 ◽  
Vol 703 ◽  
pp. 171-174
Author(s):  
Bing Wang ◽  
Yi Xiao ◽  
Shou Hui Tong ◽  
Lan Fang ◽  
Da Hai You ◽  
...  
Keyword(s):  
Water Quality ◽  
Organic Matter ◽  
Fluidized Bed ◽  
Removal Efficiency ◽  
Nitrogen Removal ◽  
Removal Rate ◽  
Operating Conditions ◽  
Removal Mechanism ◽  
Aerobic Zone

Improved step-feed de-nitrification progress combined with biological fluidized bed was introduced in this study. The progress had good performance and capacity of de-nitrification and organic matter. The experiment result showed that the de-nitrification efficiency of the improved biological fluidized bed with step-feed process was higher than the fluidized bed A/O process under the same water quality and the operating conditions. When the influent proportion of each segment was equal, the system showed good nitrogen removal efficiency with the change of influent C/N ratio, HRT and sludge return ratio. The removal rate of TN reached up to 88.2%. It showed that the simultaneous nitrification and de-nitrification phenomenon happened in the aerobic zone. The nitrogen removal mechanism was also studied.

scholarly journals Evaluation of wet air oxidation variables for removal of organophosphorus pesticide malathion using Box-Behnken design

2016 ◽  
Vol 75 (3) ◽  
pp. 619-628 ◽  
Author(s):  
Melike Isgoren ◽  
Erhan Gengec ◽  
Sevil Veli
Keyword(s):  
Removal Efficiency ◽  
Applied Pressure ◽  
Organophosphorus Pesticide ◽  
Operating Conditions ◽  
Quadratic Model ◽  
Air Oxidation ◽  
Wet Air Oxidation ◽  
Reaction Conditions ◽  
Efficient Treatment ◽  
Optimum Reaction

This paper deals with finding optimum reaction conditions for wet air oxidation (WAO) of malathion aqueous solution, by Response Surface Methodology. Reaction conditions, which affect the removal efficiencies most during the non-catalytic WAO system, are: temperature (60–120 °C), applied pressure (20–40 bar), the pH value (3–7), and reaction time (0–120 min). Those were chosen as independent parameters of the model. The interactions between parameters were evaluated by Box-Behnken and the quadratic model fitted very well with the experimental data (29 runs). A higher value of R2 and adjusted R2 (>0.91) demonstrated that the model could explain the results successfully. As a result, optimum removal efficiency (97.8%) was obtained at pH 5, 20 bars of pressure, 116 °C, and 96 min. These results showed that Box–Behnken is a suitable design to optimize operating conditions and removal efficiency for non-catalytic WAO process. The EC20 value of raw wastewater was measured as 35.40% for malathion (20 mg/L). After the treatment, no toxicity was observed at the optimum reaction conditions. The results show that the WAO is an efficient treatment system for malathion degradation and has the ability of converting malathion to the non-toxic forms.

Treatment of dairy wastewaters by electrocoagulation using iron electrodesTraitement des eaux résiduaires d'une laiterie par électrocoagulation avec des électrodes de fer

2014 ◽  
Vol 50 (2) ◽  
pp. 198-209 ◽  
Author(s):  
Malika Aoudjehane ◽  
Mohamed Elghazali Benatallah
Keyword(s):  
Electrical Conductivity ◽  
Removal Efficiency ◽  
Current Density ◽  
Oxygen Demand ◽  
Operating Conditions ◽  
Electrolysis Time ◽  
Electrode Consumption ◽  
Treatment Conditions ◽  
Consumption Energy ◽  
Optimal Efficiency

A procedure of electrocoagulation (EC) using iron electrodes has been used for the treatment of the wastewaters produced by the Beni-Tamou dairy in Algeria. The effect of the operating conditions, such as the current intensity, the electrolysis time, the pH of the solution and the electrical conductivity, on the removal efficiency of chemical oxygen demand (COD) and the total suspended solids (TSS) has been studied. An inter-electrode distance of 1 cm has been maintained constant during the tests. It has been found that an increase in electrolysis time and current density improved the treatment significantly, albeit with a greater consumption of energy as well as an increased electrode consumption. The results of the electrocoagulation treatment under various operating conditions show that the optimal efficiency has been obtained under the following conditions: 60 minutes of electrolysis, a current density of 200 A/m2, a pH 8, an electrical conductivity of 4.72 mS/cm and a consumption energy of 13.57 kWh/m3. Under these conditions, the removal efficiency for the COD and TSS parameters is 93.26 and 99.3%, respectively. The optimal treatment conditions of dairy wastewaters have resulted in final COD and TSS concentrations of 41.5 and 27 mg/L, respectively, values that are conform to industrial liquid effluents discharge norms.

Study on the Treatment of Nitrogen Oxides by Compound Bio-Filter

2012 ◽  
Vol 610-613 ◽  
pp. 1824-1828
Author(s):  
Zhi Fei Liu ◽  
De Hong Pang
Keyword(s):  
Removal Efficiency ◽  
Gas Flow ◽  
Load Capacity ◽  
Packing Material ◽  
Operating Conditions ◽  
Inlet Concentration ◽  
Trickling Filter ◽  
Spray Volume ◽  
Packing Layer ◽  
Empty Bed Residence Time

Activated carbon and wood chips were applied respectively as packing material of bio-trickling filter and bio-filter which composed the compound bio-filter and the effect of different operating parameters on NOx removal efficiency were studied. The results show that the best operating conditions of the compound bio-filter are: NO inlet concentration 604.5 mg/m3, spray volume 1.2 L/h, gas flow 0.6 m3/h(empty bed residence time 103.7 s).In such cases,NOx removal efficiency is over 96% and NOx removal load of the packing material is 29.66 g/(m3•h) . The remove of NOx is mainly completed by the packing layer of 0~50 cm height both in the bio-trickling filter and in the bio-filter, that is to say ,when the total packing layer height of the compound bio-filter is 100 cm, the purification effect is ideal and economical; The system can return to normal in about 7 hr when the dynamic load changes largely and suddenly, showing that it has strong anti shock load capacity.

Comparative investigations on COD-removal in sequencing batch reactors and continuous flow plants

2001 ◽  
Vol 43 (3) ◽  
pp. 45-52 ◽  
Author(s):  
T. Dockhorn ◽  
N. Dichtl ◽  
R. Kayser
Keyword(s):  
Removal Efficiency ◽  
Municipal Wastewater ◽  
Plug Flow ◽  
Main Idea ◽  
Operating Conditions ◽  
Cod Removal ◽  
Batch Reactors ◽  
Mixing Characteristics ◽  
Hydraulic Load ◽  
The Individual

Investigations on enhanced COD removal from municipal wastewater were performed over a period of 2.5 years, comparing three different types of reactor. The main idea was to determine the influence of the mixing characteristics of the reactor on the treatment processes and the effluent quality. Therefore three pilot plants (a completely mixed reactor, a cascade of three reactors and a SBR) were operated under equal conditions (wastewater, hydraulic load, temperature, sludge age) in parallel to each other. Investigations were carried out at different sludge ages. It could be shown that within one sludge age the CODf removal efficiency increased, when mixing characteristics came closer to the plug flow and it also increased with higher temperatures. A significant correlation was observed between the COD removal efficiency and the sludge load. The higher the sludge load was the greater the CODf concentration in the effluent. Especially the SBR reactor showed an excellent performance under the given operating conditions. Dynamic simulation calculations were carried out, to investigate whether the influence of the type of reactor on the COD-elimination could be described theoretically by combining growth kinetics and the mixing characteristics of the individual reactors. The results showed that performance was better when mixing characteristics came closer to plug flow.

Assessing pathogen removal efficiency of microfiltration by monitoring membrane integrity

2001 ◽  
Vol 1 (4) ◽  
pp. 43-48 ◽  
Author(s):  
S.K. Hong ◽  
F.A. Miller ◽  
J.S. Taylor
Keyword(s):  
Removal Efficiency ◽  
Air Flow ◽  
Membrane Integrity ◽  
Operating Conditions ◽  
Pathogen Removal ◽  
Membrane Pore ◽  
Pressure Decay ◽  
Particle Counting ◽  
Integrity Tests ◽  
Microbial Challenge

This study was conducted to investigate the ability of various methods of monitoring membrane integrity to respond to changes in actual membrane integrity imposed by the compromised fibers within the microfiltration unit. In addition, the pilot-scale MF unit was challenged with high concentrations of coliform, Cryptosporidium, and spore, in order to assess the pathogen removal capability of microfiltration. A correlation between the integrity tests and microbial challenge data was also made. The integrity tests investigated in this study were pressure decay and diffusive air flow tests (direct integrity tests), and turbidity and particle counting (indirect integrity tests). Both pressure decay (PDT) and diffusive air flow (DAF) tests were sensitive enough to detect one damaged fiber out of 66,000. The extent of fouling did not affect the sensitivity of the PDT and DAF, showing that PDT and DAF tests are a simple, reliable means to monitor membrane integrity under field conditions. Indirect integrity monitoring using turbidity and particle counting, however, responded poorly to changes in membrane integrity. Microbial challenge study demonstrated that microfiltration was capable of removing various pathogens including Cryptosporidium, at the level required by drinking water regulations, under even adverse operating conditions. Finally, PDT and DAF tests showed a better correlation with actual microbial removal efficiency of microfiltration than turbidity and particle counting. The turbidity and particle counting grossly underestimated the removal of pathogen larger than MF membrane pore size due to poor sensitivity.

scholarly journals Modeling and Optimization for Production of Rice Husk Activated Carbon and Adsorption of Phenol

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Y. S. Mohammad ◽  
E. M. Shaibu-Imodagbe ◽  
S. B. Igboro ◽  
A. Giwa ◽  
C. A. Okuofu
Keyword(s):  
Activated Carbon ◽  
Adsorption Capacity ◽  
Removal Efficiency ◽  
Rice Husk ◽  
Adsorption Process ◽  
Operating Conditions ◽  
Optimum Operating ◽  
Process Variables ◽  
Adsorbent Dosage ◽  
Pretreatment Temperature

Modeling of adsorption process establishes mathematical relationship between the interacting process variables and process optimization is important in determining the values of factors for which the response is at maximum. In this paper, response surface methodology was employed for the modeling and optimization of adsorption of phenol onto rice husk activated carbon. Among the action variables considered are activated carbon pretreatment temperature, adsorbent dosage, and initial concentration of phenol, while the response variables are removal efficiency and adsorption capacity. Regression analysis was used to analyze the models developed. The outcome of this research showed that 99.79% and 99.81% of the variations in removal efficiency and adsorption capacity, respectively, are attributed to the three process variables considered, that is, pretreatment temperature, adsorbent dosage, and initial phenol concentration. Therefore, the models can be used to predict the interaction of the process variables. Optimization tests showed that the optimum operating conditions for the adsorption process occurred at initial solute concentration of 40.61 mg/L, pretreatment temperature of 441.46°C, adsorbent dosage 4 g, adsorption capacity of 0.9595 mg/g, and removal efficiency of 97.16%. These optimum operating conditions were experimentally validated.

Effects of Al3 +  and hydraulic characteristics on the removal and behaviour of particles in dissolved air flotation

2006 ◽  
Vol 6 (3) ◽  
pp. 89-95
Author(s):  
Jungsoo Mun ◽  
Sungwon Park ◽  
Mooyoung Han
Keyword(s):  
Turbulent Flow ◽  
Removal Efficiency ◽  
Operating Conditions ◽  
Point Of Zero Charge ◽  
Hydraulic Characteristics ◽  
Dissolved Air Flotation ◽  
Floc Size ◽  
Saturated Water ◽  
Air Flotation ◽  
Dissolved Air

The removal efficiency of the dissolved air flotation (DAF) process to separate particles from water and wastewater depends on the size and zeta potential of bubbles and particles, the solution and operating conditions, hydraulic characteristics, etc. The effects of aluminium ions and turbulent flow-produced when air-saturated water was spouted into the reactor in the DAF process, on removal and, particle behaviour were on investigated. When bubble size was similar to particle size (10–50 μm), the maximum removal efficiency was 92% in a Kaolin solution of 10−3 M Al3 +  without pre-treatment for flocculation process, and, as time passed, the floc size was observed to increase at a pH of 8, which was the condition of high removal efficiency as seen through image analysis. When the air-saturated water was spouted into the reactor, the size of particle at p.z.c. (point of zero charge) seemed to increase to form a floc due to collision effects caused by turbulent flow. Consequently, floc formation by turbulent flow in the reactor seemed to positively affect removal efficiency.

Sign in / Sign up

Export Citation Format

Share Document