Mechanical properties of gamma‐irradiated styrene‐butadiene rubber/acid‐treated vermiculite clay/maleic anhydride nanocomposites

2018 ◽  
Vol 59 (2) ◽  
pp. 355-364 ◽  
Author(s):  
Khaled F. El‐Nemr ◽  
Magdy A.M. Ali ◽  
Saleh N. Saleh ◽  
Abdel Wahab M. El‐Naggar
Keyword(s):  
Mechanical Properties ◽  
Maleic Anhydride ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Gamma Irradiated ◽  
Styrene Butadiene ◽  
Vermiculite Clay

scholarly journals Analysis of the Impact on the Mechanical Properties of Modification of Oligohydroxyethers in Organic Solvent Solution with Rubbers

Polymers ◽  
2021 ◽  
Vol 13 (4) ◽  
pp. 519
Author(s):  
Vitalii Bezgin ◽  
Agata Dudek ◽  
Adam Gnatowski
Keyword(s):  
Mechanical Properties ◽  
Scientific Paper ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Molecular Weights ◽  
Wide Range ◽  
Strength Tests ◽  
Materials Used ◽  
Styrene Butadiene ◽  
The Impact

This paper proposes and presents the chemical modification of linear hydroxyethers (LHE) with different molecular weights (380, 640, and 1830 g/mol) with the addition of three types of rubbers (polysulfide rubber (PSR), polychloroprene rubber (PCR), and styrene-butadiene rubber (SBR)). The main purpose of choosing this type of modification and the materials used was the possibility to use it in industrial settings. The modification process was conducted for a very wide range of modifier additions (rubber) per 100 g LHE. The materials obtained in the study were subjected to strength tests in order to determine the effect of the modification on functional properties. Mechanical properties of the modified materials were improved after the application of the modifier (rubber) to polyhydroxyether (up to certain modifier content). The most favorable changes in the tested materials were registered in the modification of LHE-1830 with PSR. In the case of LHE-380 and LHE-640 modified in cyclohexanol (CH) and chloroform (CF) solutions, an increase in the values of the tested properties was also obtained, but to a lesser extent than for LHE-1830. The largest changes were registered for LHE-1830 with PSR in CH solution: from 12.1 to 15.3 MPa for compressive strength tests, from 0.8 to 1.5 MPa for tensile testing, from 0.8 to 14.7 MPa for shear strength, and from 1% to 6.5% for the maximum elongation. The analysis of the available literature showed that the modification proposed by the authors has not yet been presented in any previous scientific paper.

scholarly journals Hybrid Silica-Based Fillers in Nanocomposites: Influence of Isotropic/Isotropic and Isotropic/Anisotropic Fillers on Mechanical Properties of Styrene-Butadiene (SBR)-Based Rubber

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2413
Author(s):  
Mariapaola Staropoli ◽  
Vincent Rogé ◽  
Enzo Moretto ◽  
Joffrey Didierjean ◽  
Marc Michel ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Silica Nanoparticles ◽  
Synergetic Effect ◽  
Mechanical Analysis ◽  
Rubber Matrix ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Precipitated Silica ◽  
Scanning Transmission ◽  
Styrene Butadiene

The improvement of mechanical properties of polymer-based nanocomposites is usually obtained through a strong polymer–silica interaction. Most often, precipitated silica nanoparticles are used as filler. In this work, we study the synergetic effect occurring between dual silica-based fillers in a styrene-butadiene rubber (SBR)/polybutadiene (PBD) rubber matrix. Precipitated Highly Dispersed Silica (HDS) nanoparticles (10 nm) have been associated with spherical Stöber silica nanoparticles (250 nm) and anisotropic nano-Sepiolite. By imaging filler at nano scale through Scanning Transmission Electron Microscopy, we have shown that anisotropic fillers align only in presence of a critical amount of HDS. The dynamic mechanical analysis of rubber compounds confirms that this alignment leads to a stiffer nanocomposite when compared to Sepiolite alone. On the contrary, spherical 250 nm nanoparticles inhibit percolation network and reduce the nanocomposite stiffness.

Novel modification of styrene butadiene rubber/acrylic rubber blends to improve mechanical, dynamic mechanical, and swelling behavior for oil sealing applications

2021 ◽  
pp. 096739112110313
Author(s):  
Ahmed Abdel-Hakim ◽  
Soma A el-Mogy ◽  
Ahmed I Abou-Kandil
Keyword(s):  
Mechanical Properties ◽  
Crosslink Density ◽  
Physical And Mechanical Properties ◽  
Dynamic Mechanical Properties ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Rubber Blends ◽  
Dynamic Mechanical ◽  
Oil Resistance ◽  
Styrene Butadiene

Blending of rubber is an important route to modify properties of individual elastomeric components in order to obtain optimum chemical, physical, and mechanical properties. In this study, a novel modification of styrene butadiene rubber (SBR) is made by employing acrylic rubber (ACM) to obtain blends of outstanding mechanical, dynamic, and oil resistance properties. In order to achieve those properties, we used a unique vulcanizing system that improves the crosslink density between both polymers and enhances the dynamic mechanical properties as well as its resistance to both motor and break oils. Static mechanical measurements, tensile strength, elongation at break, and hardness are improved together with dynamic mechanical properties investigated using dynamic mechanical analyses. We also proposed a mechanism for the improvement of crosslink density and consequently oil resistance properties. This opens new opportunities for using SBR/ACM blends in oil sealing applications that requires rigorous mechanical and dynamic mechanical properties.

Impact of α‐cellulose as a green filler on physico‐mechanical properties of a solution grade styrene‐butadiene rubber based tire‐tread compound

2021 ◽  
Author(s):  
Koushik Pal ◽  
Soumya Ghosh Chowdhury ◽  
Dipankar Mondal ◽  
Dipankar Chattopadhyay ◽  
Sanjay Kumar Bhattacharyya ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Styrene Butadiene
Sign in / Sign up

Export Citation Format

Share Document