Microanalyses on Mo films before and after hydrogen ion irradiation

2007 ◽  
Vol 39 (12-13) ◽  
pp. 937-941
Author(s):  
C. H. Liu ◽  
N. K. Huang ◽  
D. Z. Wang ◽  
B. Yang
Keyword(s):  
Ion Irradiation ◽  
Hydrogen Ion ◽  
Before And After

scholarly journals Evolution of native defects in ZnO nanorods irradiated with hydrogen ion

2019 ◽  
Vol 9 (1) ◽  
Author(s):  
Tengfei Wu ◽  
Aiji Wang ◽  
Li Zheng ◽  
Guangfu Wang ◽  
Qingyun Tu ◽  
...  
Keyword(s):  
Surface Passivation ◽  
Ion Irradiation ◽  
Zno Nanorods ◽  
Blue Shift ◽  
Hydrogen Ion ◽  
Silicon Substrates ◽  
Nanorod Arrays ◽  
Native Defects ◽  
Before And After ◽  
Formation And Evolution

AbstractThis work reports the study on the evolution of native defects in ZnO nanorods irradiated with hydrogen ion. ZnO nanorod arrays grown vertically on silicon substrates were irradiated by 180 keV H+ ions to a total fluence of 8.50 × 1015 ions/cm2. The X-ray diffraction spectra, photoluminescence spectra before and after irradiation and the real-time ionoluminescence spectra of the nanorod arrays during the irradiating process were measured. Formation and evolution of defects during H+ ion irradiation and effects of irradiation on the crystal structure and optical property were studied. Blue shift of exciton emission, shrink of lattice c and improvement of the crystallinity of ZnO nanorods after irradiation were observed. Simple surface passivation of the nanorods could improve the radiation resistance. Formation and evolution of the defects during H+ ion irradiation could be clarified into four stages and the related models are provided.

scholarly journals Irradiation Hardening Behavior of He-Irradiated V–Cr–Ti Alloys with Low Ti Addition

2020 ◽  
Vol 5 (1) ◽  
pp. 1
Author(s):  
Ken-ichi Fukumoto ◽  
Yoshiki Kitamura ◽  
Shuichiro Miura ◽  
Kouji Fujita ◽  
Ryoya Ishigami ◽  
...  
Keyword(s):  
Ion Irradiation ◽  
Optimum Composition ◽  
Solid Solution Hardening ◽  
Irradiation Hardening ◽  
Hardening Behavior ◽  
Ti Alloys ◽  
Void Swelling ◽  
Before And After ◽  
Cr Addition ◽  
Ti Addition

A set of V–(4–8)Cr–(0–4)Ti alloys was fabricated to survey an optimum composition to reduce the radioactivity of V–Cr–Ti alloys. These alloys were subjected to nano-indenter tests before and after 2-MeV He-ion irradiation at 500 °C and 700 °C with 0.5 dpa at peak damage to investigate the effect of Cr and Ti addition and gas impurities for irradiation hardening behavior in V–Cr–Ti alloys. Cr and Ti addition to V–Cr–Ti alloys for solid–solution hardening remains small in the unirradiated V–(4–8)Cr–(0–4)Ti alloys. Irradiation hardening occurred for all V–Cr–Ti alloys. The V–4Cr–1Ti alloy shows the highest irradiation hardening among all V–Cr–Ti alloys and the gas impurity was enhanced to increase the irradiation hardening. These results may arise from the formation of Ti(CON) precipitate that was produced by He-ion irradiation. Irradiation hardening of V–Cr–1Ti did not depend significantly on Cr addition. Consequently, for irradiation hardening and void-swelling suppression, the optimum composition of V–Cr–Ti alloys for structural materials of fusion reactor engineering is proposed to be a highly purified V–(6–8)Cr–2Ti alloy.

Hydrogen Ion Beam Processing of Single Crystal Diamond Chips

1994 ◽  
Vol 354 ◽  
Author(s):  
Shuji Kiyohara ◽  
Iwao Miyamoto
Keyword(s):  
Surface Roughness ◽  
Single Crystal ◽  
Incidence Angle ◽  
Ion Beam ◽  
Etching Rate ◽  
Hydrogen Ion ◽  
Hydrogen Ions ◽  
Ion Beam Etching ◽  
Single Crystal Diamond ◽  
Before And After

AbstractIn order to apply ion beam etching with hydrogen ions to the ultra-precision processing of diamond tools, hydrogen ion beam etching characteristics of single crystal diamond chips with (100) face were investigated. The etching rate of diamond for 500 eV and 1000 eV hydrogen ions increases with the increase of the ion incidence angle, and eventually reaches a maximum at the ion incidence angle of approximately 50°, then may decrease with the increase of the ion incidence angle. The dependence of the etching rate on the ion incidence angle of hydrogen ions is fairly similar to that obtained with argon ions. Furthermore, the surface roughness of diamond chips before and after hydrogen ion beam etching was evaluated using an atomic force microscope. Consequently, the surface roughness after hydrogen ion beam etching decreases with the increase of the ion incidence angle within range of the ion incidence angle of 60°.

Sign in / Sign up

Export Citation Format

Share Document