Engine Performance Evaluation Using Biodiesel Blends: Comparative Testing Using Mixed Edible Oils, Mixed Non-edible Oils, and Petroleum Diesel

2022 ◽  
pp. 401-409
Author(s):  
L. Atepor ◽  
A. A. Abbey ◽  
F. Odoi-Yorke
Keyword(s):  
Performance Evaluation ◽  
Edible Oils ◽  
Engine Performance ◽  
Comparative Testing ◽  
Biodiesel Blends

Engine Performance with Diesel-Biodiesel Blends Fuel and Emission Characteristics

2020 ◽  
Vol 38 (5A) ◽  
pp. 779-788
Author(s):  
Marwa N. Kareem ◽  
Adel M. Salih
Keyword(s):  
Sulfur Content ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Esterification Reaction ◽  
Biodiesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Biodiesel Blends ◽  
Fuel Blends ◽  
Hc Emissions

In this study, the sunflowers oil was utilized as for producing biodiesel via a chemical operation, which is called trans-esterification reaction. Iraqi diesel fuel suffers from high sulfur content, which makes it one of the worst fuels in the world. This study is an attempt to improve the fuel specifications by reducing the sulfur content of the addition of biodiesel fuel to diesel where this fuel is free of sulfur and has a thermal energy that approaches to diesel.20%, 30% and 50% of Biodiesel fuel were added to the conventional diesel. Performance tests and pollutants of a four-stroke single-cylinder diesel engine were performed. The results indicated that the brake thermal efficiency a decreased by (4%, 16%, and 22%) for the B20, B30 and B50, respectively. The increase in specific fuel consumption was (60%, 33%, and 11%) for the B50, B30, and B20 fuels, respectively for the used fuel blends compared to neat diesel fuel. The engine exhaust gas emissions measures manifested a decreased of CO and HC were CO decreased by (13%), (39%) and (52%), and the HC emissions were lower by (6.3%), (32%), and (46%) for B20, B30 and B50 respectively, compared to diesel fuel. The reduction of exhaust gas temperature was (7%), (14%), and (32%) for B20, B30 and B50 respectively. The NOx emission increased with the increase in biodiesel blends ratio. For B50, the raise was (29.5%) in comparison with diesel fuel while for B30 and B20, the raise in the emissions of NOx was (18%) and...

Analysis of Engine Performance and Combustion Characteristics of Diesel and Biodiesel blends in a Compression Ignition Engine

2016 ◽  
Author(s):  
Henrique Dornelles ◽  
Jácson Antolini ◽  
Rafael Sari ◽  
Macklini Dalla Nora ◽  
Paulo Romeu Machado ◽  
...  
Keyword(s):  
Engine Performance ◽  
Combustion Characteristics ◽  
Compression Ignition ◽  
Compression Ignition Engine ◽  
Biodiesel Blends

Exergy and Energy Analysis of α-Fe2O3-Doped Al2O3 Nanocatalyst-Based Biodiesel Blends—Performance and Emission Characteristics

2021 ◽  
Vol 143 (12) ◽  
Author(s):  
A. Anderson ◽  
Amal M. Al-Mohaimeed ◽  
Mohamed Soliman Elshikh ◽  
T. R. Praveenkumar ◽  
M. Sekar
Keyword(s):  
Carbon Monoxide ◽  
Energy Analysis ◽  
Unsaturated Fatty Acids ◽  
Engine Performance ◽  
Volume Ratio ◽  
Emission Characteristics ◽  
Biodiesel Blends ◽  
Performance And Emission ◽  
High Area ◽  
Load Conditions

Abstract The current study emphasis on the engine performance and emission characteristics of rapeseed and soya biodiesel dispersion on a novel nanocatalyst at different concentrations of 25 ppm and 50 ppm. The results of this study were compared with those of conventional diesel at varying load conditions on a combustion ignition engine. An α-Fe2O3-doped Al2O3 was mixed with rapeseed biodiesel and soya biodiesel using an ultrasonicator at a frequency of 25 kHz. This study revealed that the incorporation of nanoparticles in biodiesel enhanced the performance of the blends by reducing the content of lignin and other unsaturated fatty acids. The improvement in the performance of the engine is mainly attributed to the high area-to-volume ratio of the nanocatalyst. Emissions of NOx. hydrocarbon and carbon monoxide during the combustion reaction increased significantly when nanoparticles were added at higher concentrations. Contrastingly, the emission of NOx in pure biodiesel was higher than that in conventional diesel. The addition of nanoparticles reduced CO emissions due to the presence of extra oxygen molecules and converted carbon monoxide into carbon dioxide. Soya seed biodiesel blends with 50 ppm nanoparticles showed better engine performance and emission characteristics as compared with all other blends.

Multiple fuel injection strategy for premixed charge compression ignition combustion engine using biodiesel blends

2022 ◽  
pp. 146808742110667
Author(s):  
Akhilendra Pratap Singh ◽  
Ashutosh Jena ◽  
Avinash Kumar Agarwal
Keyword(s):  
Alternative Fuels ◽  
Fuel Injection ◽  
Engine Performance ◽  
Pilot Injection ◽  
Compression Ignition ◽  
Combustion Control ◽  
Combustion Mode ◽  
Biodiesel Blends ◽  
Injection Parameters ◽  
Study Results

In the last decade, advanced combustion techniques of the low-temperature combustion (LTC) family have attracted researchers because of their excellent emission characteristics; however, combustion control remains the main issue for the LTC modes. The objective of this study was to explore premixed charge compression ignition (PCCI) combustion mode using a double pilot injection (DPI; pilot-pilot-main) strategy to achieve superior combustion control and to tackle the soot-oxides of nitrogen (NOx) trade-off. Experiments were carried out in a single-cylinder research engine fueled with 20% v/v biodiesel blended with mineral diesel (B20) and 40% v/v biodiesel blended with mineral diesel (B40) vis-à-vis baseline mineral diesel. Engine speed and rate of fuel-mass injected were maintained constant at 1500 rpm and 0.6 kg/h mineral diesel equivalent, respectively. Pilot injection timings (at 45° and 35° before top dead center (bTDC)) and fuel quantities were fixed, while three fuel injection pressures (FIPs) and four different start of the main injection (SoMI) timings were investigated in this study. Results showed that multiple pilot injections resulted in a stable PCCI combustion mode, making it suitable for higher engine loads. For all test fuels, advancing SoMI timings led to relatively lesser knocking; however, engine performance characteristics degraded at advanced SoMI timings. B40 exhibited relatively superior engine performance among different test fuels at lower FIP; however, the difference in engine performance was insignificant at higher FIPs. Fuel injection parameters showed a significant effect on emissions, especially on the NOx and particulates. Advancing SoMI timing resulted in 20%–50% lower particulates emissions with a slight NOx increase; however, the differences in emissions at different SoMI timings reduced at higher FIPs. Somewhat higher particulates from biodiesel blends were a critical observation of this study, which was more dominant at advanced SoMI timings. Qualitative correlation between NOx-total particulate mass (TPM) was another critical analysis, which exhibited the relative importance of different fuel injection parameters for other alternative fuels. Overall, B20 at 700 bar FIP and 20° SoMI timing emerged as the most promising proposition with some penalty in CO emission.

scholarly journals THE EFFECT OF DIESEL-BIODIESEL BLENDS ON THE PERFORMANCE AND EXHAUST EMISSIONS OF A DIRECT INJECTION OFF-ROAD DIESEL ENGINE

Transport ◽  
2014 ◽  
Vol 29 (4) ◽  
pp. 440-448 ◽  
Author(s):  
Tomas Mickevičius ◽  
Stasys Slavinskas ◽  
Slawomir Wierzbicki ◽  
Kamil Duda
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Engine Performance ◽  
Exhaust Emissions ◽  
Bench Test ◽  
Maximum Pressure ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Performance And Emission

This paper presents a comparative analysis of the diesel engine performance and emission characteristics, when operating on diesel fuel and various diesel-biodiesel (B10, B20, B40, B60) blends, at various loads and engine speeds. The experimental tests were performed on a four-stroke, four-cylinder, direct injection, naturally aspirated, 60 kW diesel engine D-243. The in-cylinder pressure data was analysed to determine the ignition delay, the Heat Release Rate (HRR), maximum in-cylinder pressure and maximum pressure gradients. The influence of diesel-biodiesel blends on the Brake Specific Fuel Consumption (bsfc) and exhaust emissions was also investigated. The bench test results showed that when the engine running on blends B60 at full engine load and rated speed, the autoignition delay was 13.5% longer, in comparison with mineral diesel. Maximum cylinder pressure decreased about 1–2% when the amount of Rapeseed Methyl Ester (RME) expanded in the diesel fuel when operating at full load and 1400 min–1 speed. At rated mode, the minimum bsfc increased, when operating on biofuel blends compared to mineral diesel. The maximum brake thermal efficiency sustained at the levels from 0.3% to 6.5% lower in comparison with mineral diesel operating at full (100%) load. When the engine was running at maximum torque mode using diesel – RME fuel blends B10, B20, B40 and B60 the total emissions of nitrogen oxides decreased. At full and moderate load, the emission of carbon monoxide significantly raised as the amount of RME in fuel increased.

scholarly journals INVESTIGATION ON DIESEL ENGINE FUELLED BY MAHUA BIODIESEL

2021 ◽  
Vol 9 (1) ◽  
pp. 436-443
Author(s):  
M.Kannan, R.Balaji, R.T Sarath Babu, Chandrakant B. Shende, Ashish Selokar
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Primary Objective ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Biodiesel Blends ◽  
Mahua Oil ◽  
Mahua Biodiesel

The primary objective of this study is to discover the effects of injection timing on performance, emission and combustion characteristics effect of advanced and retarded injection timing of the engine fuelled with mahua oil biodiesel blends. The engine performance, combustion and emission characteristics of the mahua oil biodiesel blends (B20, B40, B60, B80and B100) are investigated in this experimentation without any modification of the diesel engine. At this advanced pressure t he efficiency of engine by means of CO, Unburned HC gases and smoke emissions with higher oxides of nitrogen was observed compared to diesel. The obtained results are compared with a neat diesel and mahua oil biodiesel blends are shown through the graphs. From this study, identifies optimum fuel blend of this work. Thus, the combustion of duration is similar in all variance in pressure. This research paved a way to bio-diesel in mahua oil mixture and draws best outcome in emission less and to maintain eco-friendly environment.  

Impacts of N, N'-diphenyl-1, 4-phenylenediamine (DPPD) Antioxidant Additive in Jatropha Biodiesel Blends to Reduce NOx Emission of a Multi Cylinder Vehicle Type Diesel Engine

2013 ◽  
Vol 774-776 ◽  
pp. 784-790
Author(s):  
S.M. Palash ◽  
M.A. Kalam ◽  
H.H. Masjuki ◽  
B.M. Masum
Keyword(s):  
Diesel Engine ◽  
Engine Performance ◽  
Exhaust Emission ◽  
Antioxidant Additive ◽  
Biodiesel Blends ◽  
Market Expansion ◽  
Treatment Techniques ◽  
Pre Treatment ◽  
Biodiesel Fuels ◽  
Full Throttle

To meet stringent exhaust emission norms worldwide, various exhaust pre-treatment and post-treatment techniques have been employed in modern engines. Using antioxidant additives in biodiesel fuels is a promising and effective NOx reduction technology. Non-edible jatropha oil based methyl ester was produced and blended with conventional diesel. Five fuel samples (Diesel, JB5, JB5DPPD0.15%, JB15 and JB15DPPD0.15%) were tested for their use as substitute fuel for a radiator-cooled four cylinder diesel engine. Experiment results show that DPPD antioxidant additive could be reduced NOx emission significantly with slight penalty on engine performance as well as CO and HC emission. However, when compared to diesel combustion the emissions of HC and CO were found nearly same or below. By addition of 0.15% (m) DPPD additive in JB5 and JB15 reduction of NOx emission were 12.68% and 13.36 % compared to biodiesel blends without additive at full throttle position. As conclusion, JB5 and JB15 with addition of 0.15% (m) can be used in four cylinder diesel engine to reduce NOx and consequently overcome the barrier to market expansion of biodiesel fuels.

Aero Engine Performance Evaluation During Missile Firing Test

2017 ◽  
Author(s):  
Sajath Kumar Manoharan ◽  
Kasram Santhosh ◽  
Mahesh P. Padwale ◽  
G. P. Ravishankar
Keyword(s):  
Performance Evaluation ◽  
Engine Performance ◽  
Flight Testing ◽  
Flow Disturbance ◽  
Fighter Aircraft ◽  
Firing Test ◽  
Aero Engine ◽  
Temperature Ramps ◽  
Air Intake ◽  
Model Engine

Evaluation of engine performance during armament firing in fighter aircraft is a vital qualification aspect for airframe engine integration. Ingestion of missile’s efflux into air intake results in rapid increase of engine inlet temperatures (temperature ramps) which cause flow disturbance to the compressor. Temperature distortion caused due to armament firing and its effect on compressor stability during flight testing is evaluated. Accordingly mitigation actions are recommended for stall/surge free operations. Distortion descriptors are assessed using simulation model (engine performance program) and results compared with engine distortion limits.

Sign in / Sign up

Export Citation Format

Share Document