Calculating Transverse Vibration of a Continuous Beam on Nonlinear Viscoelastic Supports Under the Action of Moving Loads

Author(s):  
Pham Thanh Chung ◽  
Nguyen Minh Phuong
2005 ◽  
Vol 83 (23-24) ◽  
pp. 1865-1877 ◽  
Author(s):  
M.H. Kargarnovin ◽  
D. Younesian ◽  
D.J. Thompson ◽  
C.J.C. Jones

1987 ◽  
Vol 109 (4) ◽  
pp. 361-365 ◽  
Author(s):  
R. Katz ◽  
C. W. Lee ◽  
A. G. Ulsoy ◽  
R. A. Scott

The dynamic stability and transverse vibration of a beam subject to a deflection dependent moving load is considered. The deflection dependent moving load is motivated by the cutting forces in machining operations. Galerkin’s method is used to obtain a set of ordinary differential equations with periodic coefficients. It is found that parametric instability can be expected for a continuous sequence of moving loads. The response under the moving deflection dependent load is also calculated.


2014 ◽  
Vol 638-640 ◽  
pp. 1079-1084 ◽  
Author(s):  
Chang Zhao Qian ◽  
Chang Ping Chen ◽  
Yong Gang Xiao

Vehicle axle loads are modeled as moving loads and bridge is considered as a continuous beam. Based on the modal superposition theory, the model accelerations can be obtained from the accelerations of the bridge at several sections. Then based on the d’Alembertian theory, the inertia force of the bridge can be expressed approximately. Using the bending moment influence lines, the equations about flexural moment and moving force is obtained. Using the formulas, the moving force can be obtained at any time. Examples show that the method has high accuracy in identifying varying time moving force as well as constant moving force. This method has highly efficiency and appropriate to applying in engineering.


TAPPI Journal ◽  
2019 ◽  
Vol 18 (11) ◽  
pp. 641-649
Author(s):  
JOSHUA OMAMBALA ◽  
CARL MCINTYRE

The vast majority of tissue production uses creping to achieve the required set of properties on the base sheet. The Yankee coating helps to develop the desired crepe that in turn determines properties such as bulk and softness. The adhesion of the sheet to the Yankee surface is a very important characteristic to consider in achieving the desired crepe. The coating mix usually consists of the adhesive, modifier, and release. A good combination of these components is essential to achieving the desired properties of the tissue or towel, which often are determined by trials on the machine that can be time consuming and lead to costly rejects. In this paper, five compositions of an industrial Yankee coating adhesive, modifier, and release were examined rheologically. The weight ratio of the adhesive was kept constant at 30% in all five compositions and the modifier and release ratios were varied. The normal force and work done by the different compositions have been shown at various temperatures simulating that of the Yankee surface, and the oscillatory test was carried out to explain the linear and nonlinear viscoelastic characteristic of the optimal coating composition.


2020 ◽  
Vol 7 (3) ◽  
pp. 52-56
Author(s):  
MMATMATISA JALILOV ◽  
◽  
RUSTAM RAKHIMOV ◽  

This article discusses the analysis of the general equations of the transverse vibration of a piecewise homogeneous viscoelastic plate obtained in the “Oscillation of inlayer plates of constant thickness” [1]. In the present work on the basis of a mathematical method, the approached theory of fluctuation of the two-layer plates, based on plate consideration as three dimensional body, on exact statement of a three dimensional mathematical regional problem of fluctuation is stood at the external efforts causing cross-section fluctuations. The general equations of fluctuations of piecewise homogeneous viscoelastic plates of the constant thickness, described in work [1], are difficult on structure and contain derivatives of any order on coordinates x, y and time t and consequently are not suitable for the decision of applied problems and carrying out of engineering calculations. For the decision of applied problems instead of the general equations it is expedient to use confidants who include this or that final order on derivatives. The classical equations of cross-section fluctuation of a plate contain derivatives not above 4th order, and for piecewise homogeneous or two-layer plates the elementary approached equation of fluctuation is the equation of the sixth order. On the basis of the analytical decision of a problem the general and approached decisions of a problem are under construction, are deduced the equation of fluctuation of piecewise homogeneous two-layer plates taking into account rigid contact on border between layers, and also taking into account mechanical and rheological properties of a material of a plate. The received theoretical results for the decision of dynamic problems of cross-section fluctuation of piecewise homogeneous two-layer plates of a constant thickness taking into account viscous properties of their material allow to count more precisely the is intense-deformed status of plates at non-stationary external loadings.


2006 ◽  
Vol 11 (3) ◽  
pp. 293-318 ◽  
Author(s):  
M. Zribi ◽  
N. B. Almutairi ◽  
M. Abdel-Rohman

The flexibility and low damping of the long span suspended cables in suspension bridges makes them prone to vibrations due to wind and moving loads which affect the dynamic responses of the suspended cables and the bridge deck. This paper investigates the control of vibrations of a suspension bridge due to a vertical load moving on the bridge deck with a constant speed. A vertical cable between the bridge deck and the suspended cables is used to install a hydraulic actuator able to generate an active control force on the bridge deck. Two control schemes are proposed to generate the control force needed to reduce the vertical vibrations in the suspended cables and in the bridge deck. The proposed controllers, whose design is based on Lyapunov theory, guarantee the asymptotic stability of the system. The MATLAB software is used to simulate the performance of the controlled system. The simulation results indicate that the proposed controllers work well. In addition, the performance of the system with the proposed controllers is compared to the performance of the system controlled with a velocity feedback controller.


Sign in / Sign up

Export Citation Format

Share Document