A Novel Multi-objective Optimization Framework Combining NSGA-II and MOEA/D

Author(s):  
Xin Qiu ◽  
Ye Huang ◽  
Kay Chen Tan
2021 ◽  
Author(s):  
Sijie Tang ◽  
Jiping Jiang ◽  
Yi Zheng

<p>Practitioners usually design the plan of Sponge City construction (SCC) by combining LID facilities (e.g., rain garden, rain barrels, green roofs, and grassed swales) according to their personal experiences or general guidelines. The layout (including selection, connection and distribution area) of LID facilities is subjective, in the risk of far from optimal combination. Previous researchers have developed some LID optimization tools, which only consider the dimension and number of LIDs in a given scenario. Therefore, it is necessary to develop a flexible and extensible design tool with the support of urban hydrological model to conduct the facilities layout optimization. This study introduced a SWMM-based multi-variable and multi-objective optimization framework called CAFID (Comprehensive Assessment and Fine Design Model of Sponge City) to meet this end. The assessment module with multi-objective couples diverse controlling end-points (e.g., total runoff, peak runoff, pollutant concentration, cost, and customized social-ecological factors) as the candidates of assessment criteria. The optimization module with multi-variable is implemented by SWMM, starting with three steps: 1) Full allocation. Based on the availability, list the candidates of LID facility for each sub-catchment; 2) Full connection. Order the potential stream direction of surface runoff from rainfall to municipal network, based on possible hierarchical structure of sub-catchments and LID facilities; 3) Full coverage. Identify all the suitable area for LID facility in sub-catchment. The optimization on the 3 variables, the selection, connection, and area, is powered by NSGA-II and TOPSIS algorithms, which make it possible that we choose a final result from the set of nondominated solutions according to special weight distribution. The effectiveness of CAFID was illustrated through a case of Sponge City in Fenghuangcheng of Shenzhen City, one of 30 national pilot sponge cities in China. As well, this new framework is expected to be widely verified and applied in Sponge City construction in China or similar concepts all over the world.</p>


Author(s):  
Sarat Kumar Das

Slope stability of different waste containment systems is a matter of serious concern due to its impact on air, land, and water pollution, affecting human and aquatic lives. It has been observed that most of the waste containment slope failures are translational failure. In this chapter, the slope stability analysis of the waste containment is discussed with translational failure (wedge analysis) in single and multi-objective optimization framework using genetic algorithm (GA). Non-dominated sorting genetic algorithm II (NSGA-II) is found to efficient in developing the Pareto front in terms of factor of safety (FOS), height of embankment, and volume of the failed slope. The FOS decreased with increase in height of the slope and the volume of the slope also increased. The optimized slope in terms of different slope angle and with seismic coefficients is also discussed. Such a study will help the professional in deciding the height of the slope as per the FOS in a specified seismic zone.


Sensors ◽  
2021 ◽  
Vol 21 (8) ◽  
pp. 2775
Author(s):  
Tsubasa Takano ◽  
Takumi Nakane ◽  
Takuya Akashi ◽  
Chao Zhang

In this paper, we propose a method to detect Braille blocks from an egocentric viewpoint, which is a key part of many walking support devices for visually impaired people. Our main contribution is to cast this task as a multi-objective optimization problem and exploits both the geometric and the appearance features for detection. Specifically, two objective functions were designed under an evolutionary optimization framework with a line pair modeled as an individual (i.e., solution). Both of the objectives follow the basic characteristics of the Braille blocks, which aim to clarify the boundaries and estimate the likelihood of the Braille block surface. Our proposed method was assessed by an originally collected and annotated dataset under real scenarios. Both quantitative and qualitative experimental results show that the proposed method can detect Braille blocks under various environments. We also provide a comprehensive comparison of the detection performance with respect to different multi-objective optimization algorithms.


Machines ◽  
2021 ◽  
Vol 9 (6) ◽  
pp. 107
Author(s):  
Rongchao Jiang ◽  
Zhenchao Jin ◽  
Dawei Liu ◽  
Dengfeng Wang

In order to reduce the negative effect of lightweighting of suspension components on vehicle dynamic performance, the control arm and torsion beam widely used in front and rear suspensions were taken as research objects for studying the lightweight design method of suspension components. Mesh morphing technology was employed to define design variables. Meanwhile, the rigid–flexible coupling vehicle model with flexible control arm and torsion beam was built for vehicle dynamic simulations. The total weight of control arm and torsion beam was taken as optimization objective, as well as ride comfort and handling stability performance indexes. In addition, the fatigue life, stiffness, and modal frequency of control arm and torsion beam were taken as the constraints. Then, Kriging model and NSGA-II were adopted to perform the multi-objective optimization of control arm and torsion beam for determining the lightweight scheme. By comparing the optimized and original design, it indicates that the weight of the optimized control arm and torsion beam are reduced 0.505 kg and 1.189 kg, respectively, while structural performance and vehicle performance satisfy the design requirement. The proposed multi-objective optimization method achieves a remarkable mass reduction, and proves to be feasible and effective for lightweight design of suspension components.


2021 ◽  
Author(s):  
Varun Ojha ◽  
Giorgio Jansen ◽  
Andrea Patanè ◽  
Antonino La Magna ◽  
Vittorio Romano ◽  
...  

AbstractWe propose a two-stage multi-objective optimization framework for full scheme solar cell structure design and characterization, cost minimization and quantum efficiency maximization. We evaluated structures of 15 different cell designs simulated by varying material types and photodiode doping strategies. At first, non-dominated sorting genetic algorithm II (NSGA-II) produced Pareto-optimal-solutions sets for respective cell designs. Then, on investigating quantum efficiencies of all cell designs produced by NSGA-II, we applied a new multi-objective optimization algorithm II (OptIA-II) to discover the Pareto fronts of select (three) best cell designs. Our designed OptIA-II algorithm improved the quantum efficiencies of all select cell designs and reduced their fabrication costs. We observed that the cell design comprising an optimally doped zinc-oxide-based transparent conductive oxide (TCO) layer and rough silver back reflector (BR) offered a quantum efficiency ($$Q_e$$ Q e ) of 0.6031. Overall, this paper provides a full characterization of cell structure designs. It derives relationship between quantum efficiency, $$Q_e$$ Q e of a cell with its TCO layer’s doping methods and TCO and BR layer’s material types. Our solar cells design characterization enables us to perform a cost-benefit analysis of solar cells usage in real-world applications.


Author(s):  
Qianhao Xiao ◽  
Jun Wang ◽  
Boyan Jiang ◽  
Weigang Yang ◽  
Xiaopei Yang

In view of the multi-objective optimization design of the squirrel cage fan for the range hood, a blade parameterization method based on the quadratic non-uniform B-spline (NUBS) determined by four control points was proposed to control the outlet angle, chord length and maximum camber of the blade. Morris-Mitchell criteria were used to obtain the optimal Latin hypercube sample based on the evolutionary operation, and different subsets of sample numbers were created to study the influence of sample numbers on the multi-objective optimization results. The Kriging model, which can accurately reflect the response relationship between design variables and optimization objectives, was established. The second-generation Non-dominated Sorting Genetic algorithm (NSGA-II) was used to optimize the volume flow rate at the best efficiency point (BEP) and the maximum volume flow rate point (MVP). The results show that the design parameters corresponding to the optimization results under different sample numbers are not the same, and the fluctuation range of the optimal design parameters is related to the influence of the design parameters on the optimization objectives. Compared with the prototype, the optimized impeller increases the radial velocity of the impeller outlet, reduces the flow loss in the volute, and increases the diffusion capacity, which improves the volume flow rate, and efficiency of the range hood system under multiple working conditions.


2016 ◽  
Vol 122 (6) ◽  
Author(s):  
Zhongmei Gao ◽  
Xinyu Shao ◽  
Ping Jiang ◽  
Chunming Wang ◽  
Qi Zhou ◽  
...  

Energies ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4466
Author(s):  
Maël Riou ◽  
Florian Dupriez-Robin ◽  
Dominique Grondin ◽  
Christophe Le Loup ◽  
Michel Benne ◽  
...  

Microgrids operating on renewable energy resources have potential for powering rural areas located far from existing grid infrastructures. These small power systems typically host a hybrid energy system of diverse architecture and size. An effective integration of renewable energies resources requires careful design. Sizing methodologies often lack the consideration for reliability and this aspect is limited to power adequacy. There exists an inherent trade-off between renewable integration, cost, and reliability. To bridge this gap, a sizing methodology has been developed to perform multi-objective optimization, considering the three design objectives mentioned above. This method is based on the non-dominated sorting genetic algorithm (NSGA-II) that returns the set of optimal solutions under all objectives. This method aims to identify the trade-offs between renewable integration, reliability, and cost allowing to choose the adequate architecture and sizing accordingly. As a case study, we consider an autonomous microgrid, currently being installed in a rural area in Mali. The results show that increasing system reliability can be done at the least cost if carried out in the initial design stage.


Sign in / Sign up

Export Citation Format

Share Document