Domain Ontology for Expressing Knowledge of Variants of Thermally Modified Wood Products

2018 ◽  
pp. 161-171
Author(s):  
Hele-Mai Haav ◽  
Riina Maigre
Keyword(s):  
Domain Ontology ◽  
Wood Products ◽  
Thermally Modified Wood ◽  
Modified Wood

scholarly journals Increasing the Strength of the Glue Line in the Production of Thermally Modified Wood Paneling

Coatings ◽  
2021 ◽  
Vol 11 (2) ◽  
pp. 253
Author(s):  
Ruslan Rushanovich Safin ◽  
Aigul Ravilevna Shaikhutdinova ◽  
Ruslan Khasanshin ◽  
Shamil Mukhametzyanov ◽  
Albina Safina
Keyword(s):  
Wood Products ◽  
Ultraviolet Rays ◽  
Surface Activation ◽  
Wood Block ◽  
Two Stage ◽  
Adhesion Properties ◽  
Wood Processing ◽  
Ultraviolet Treatment ◽  
Thermally Modified Wood ◽  
Modified Wood

This work is devoted to the study of the effect of ultraviolet rays for the surface activation of pine wood thermally modified at temperatures of 180−240 °C in order to increase the surface roughness, enhance the wettability of thermal wood and the adhesive strength of the glue in the production of wood block furniture panels. Studies were carried out to measure the contact angle of wettability of thermally modified wood samples of pine, as a result of which it was determined that the ultraviolet treatment process contributes to an increase in the adhesion properties of the surface layer of thermally modified wood by more than 13% due to the reactivity of ultraviolet rays to oxidize and degrade ligno-containing wood products. At the same time, the most active process of surface activation takes place during 60 min of ultraviolet irradiation of wood with a total irradiation of at least 125 W/cm2. It was revealed that the combined effect of two-stage wood processing, including preliminary volumetric thermal modification followed by surface ultraviolet treatment, causes an increase in the moisture resistance of glued wood products by 24%. So, if the strength of the glue seam when gluing natural wood samples after boiling decreased by 46%, then the samples that underwent two-stage processing showed a decrease only by 22%. In connection with the results obtained, an improved technology for the production of furniture boards for the manufacture of moisture-resistant wood products is proposed.

scholarly journals Establishment of moisture diffusion regularities through the polymer shell of thermally modified wood

2021 ◽  
Vol 12 (1) ◽  
pp. 41-47
Author(s):  
Yu. V. Tsapko ◽  
O. Yu. Horbachova
Keyword(s):  
Dimensional Stability ◽  
Experimental Studies ◽  
Treated Wood ◽  
Moisture Diffusion ◽  
Wood Products ◽  
Heating Process ◽  
Polymer Shell ◽  
Coating Application ◽  
Thermally Modified Wood ◽  
Modified Wood

An analysis of the process of thermal modification of wood, which was obtained by a controlled heating process, was done. The unique technological properties (durability, low hygroscopicity and dimensional stability) of thermomodified wood make it possible to use it in various scope. Due to the influence of temperature there are some chemical changes in the structures of the wood cell wall components (lignin, cellulose and hemicellulose). This leads to an increase in density, hardness, improved hydrophobicity (water repellency), thereby reducing their ability to absorb moisture and swell. The products absorb moisture gradually, are less prone to swelling and shrinkage, but still need the elastic coatings application. It is proved that heat-treated wood turns gray over time under the influence of sunlight, and therefore requires additional surface treatment with a coating. Additional protective substances application on the thermo-modified wood products surface promotes dimensional stability and protects against rapid weathering of the surface in open air conditions. The use of transparent coatings and oils does not protect the surface from discoloration during weathering. They are recommended for products are manufactured from thermomodified wood, which are operated away from direct sunlight and rain. The parameters of moisture penetration into wood are mathematically modeled on the basis of the moisture diffusion quasi-stationary equation through the polymer coating on the flat sample surface. The dynamics of moisture content changes in thermally modified wood by different schedules parameters has been experimentally studied. The obtained mathematical relations based on the experimental studies results make it possible to calculate the moisture diffusion coefficient in thermally modified wood in the presence of a polymer shell. It is established that the wax coating application on the surface of the product reduces the moisture diffusion process more than 10 times for surfaces treated at a temperature of 160 °C for 1 hour. That is, such products can be used on objects with high humidity.

Influence of Different Modifications on Bending Strength of Wood

2019 ◽  
Vol 800 ◽  
pp. 240-245
Author(s):  
Andis Antons ◽  
Dace Cīrule ◽  
Ingeborga Andersone ◽  
Anrijs Verovkins ◽  
Edgars Kuka
Keyword(s):  
Thermal Treatment ◽  
Bending Strength ◽  
Treatment Method ◽  
Thermal Modification ◽  
Wood Products ◽  
Bending Properties ◽  
Wood Protection ◽  
Thermally Modified Wood ◽  
Mild Temperature ◽  
Modified Wood

Despite intensive research in wood protection, no simple wood treatment method is available for satisfactory wood protection that could ensure appropriate strength and bio-resistance of wood products during their service life. The present study is a part of a project that is aimed to improve wood service properties by combining wood thermal treatment and impregnation with copper containing preservatives. The objective of the present study was to investigate the effect of conventional modifications (thermal modification at relatively mild temperature range (150 - 180°C) and impregnation) and double-treatments (impregnation after thermal treatment and vice versa) on the bending properties of birch (Betula spp.) and pine (Pinussylvestris L.) wood. Bending strength considerably decreased after thermal modification of wood, however MOE values generally did not significantly change. Moreover, impregnation had no effect on the bending properties for both unmodified and thermally modified wood specimens. For double-treatment in which impregnation was carried out before thermal modification no changes in bending strength were observed comparing to thermally modified wood. However, MOE values of these specimens were 10 % for birch and 19 % for pine smaller comparing to just thermally modified wood. The results of double-treatment tests imply that, regarding wood bending properties, wood impregnation after thermal modification is more appropriate.

scholarly journals Measurement of the degree of polarisation of thermally modified Scots pine using a Stokes imaging polarimeter

2020 ◽  
Vol 27 (2) ◽  
pp. 178-182
Author(s):  
Ilpo Niskanen ◽  
Jukka Räty ◽  
Hariyadi Soetedjo ◽  
Kenichi Hibino ◽  
Hiroshi Oohashi ◽  
...  
Keyword(s):  
Scots Pine ◽  
Treatment Time ◽  
Wood Products ◽  
Maximum Temperature ◽  
Reflected Light ◽  
Heat Treated ◽  
Polarised Light ◽  
Thermally Modified Wood ◽  
Modified Wood

AbstractThis study measured the polarised light reflected from the surface of thermally modified Scots pine (Pinus sylvestris L.) wood using a Stokes imaging polarimeter. The data were analysed using the Mueller matrix method. The Scots pine boards were heat treated in an oven at temperatures of 160 ºC, 200 ºC and 220 ºC, with a heat treatment time of 3 h at the maximum temperature. The results indicated that the chemical composition of the thermally modified wood underwent a permanent transformation, leading to a change in the degree of polarisation of the reflected light. The presented method provides useful information for inspecting the quality of thermally modified wood products.

scholarly journals Corrosiveness of Thermally Modified Wood

Forests ◽  
2019 ◽  
Vol 11 (1) ◽  
pp. 50 ◽  
Author(s):  
Samuel Zelinka ◽  
Leandro Passarini ◽  
Frederick Matt ◽  
Grant Kirker
Keyword(s):  
Stainless Steel ◽  
Carbon Steel ◽  
Water Vapor Sorption ◽  
Thermal Modification ◽  
Wood Products ◽  
Galvanized Steel ◽  
Exposure Test ◽  
Corrosion Rates ◽  
Thermally Modified Wood ◽  
Modified Wood

Thermally modified wood is becoming commercially available in North America for use in outdoor applications. While there have been many studies on how thermal modification affects the dimensional stability, water vapor sorption, and biodeterioration of wood, little is known about whether thermally modified wood is corrosive to metal fasteners and hangers used to hold these members in place. As thermally modified wood is used in outdoor applications, it has the potential to become wet which may lead to corrosion of embedded fasteners. Here, we examine the corrosiveness of thermally modified ash and oak in an exposure test where stainless steel, hot-dip galvanized steel, and carbon steel nails are driven into wood and exposed to a nearly 100% relative humidity environment at 27 °C for one year. The corrosion rates were compared against control specimens of untreated and preservative-treated southern pine. Stainless steel fasteners did not corrode in any specimens regardless of the treatment. The thermal modification increased the corrosiveness of the ash and oak, however, an oil treatment that is commonly applied by the manufacturer to the wood after the heat treatment reduced the corrosiveness. The carbon steel fasteners exhibited higher corrosion rates in the thermally modified hardwoods than in the preservative-treated pine control. Corrosion rates of galvanized fasteners in the hardwoods were much lower than carbon steel fasteners. These data can be used to design for corrosion when building with thermally modified wood, and highlight differences between corrosion of metals embedded in wood products.

scholarly journals OPTIMIZATION OF PROTECTIVE COATING COMPONENTS OF THERMOMODIFIED WOOD TO THE EXPOSURE OF WATER

2021 ◽  
pp. 101-109
Author(s):  
Yu. Tsapko ◽  
◽  
A.Yu. Gorbachova ◽  
S.N. Mazurchuk ◽  
O. Bondarenko ◽  
...  
Keyword(s):  
Water Absorption ◽  
Protective Coating ◽  
Moisture Absorption ◽  
Thermal Modification ◽  
Wood Products ◽  
Operating Conditions ◽  
Photochemical Degradation ◽  
Thermally Modified Wood ◽  
Wood Surfaces ◽  
Modified Wood

Abstract. Paints and varnishes are used to a large extent to protect wood surfaces in outdoor conditions, as they are easy to maintain and reapply. Also, when developing a coating, manufacturers are guided by the need to obtain a number of properties that generally determine its ability to protect against moisture. To obtain a protective coating that meets the specified requirements, it is necessary that the components that make up the coating belong directly to the group of protective materials or form such compounds under operating conditions, be able to adhere to the surface of the product. It was found that thermal modification provides a decrease in water absorption of wood. Additional processing of the wood surface helps to reduce moisture absorption by 2 times, and for samples modified at a temperature of 220 °C – 3 times. Geometric dimensional stability is also improved by a factor of 2. The effect of heat treatment on the water absorption of wood is somewhat less – for samples modified at 190 and 220 °C for more than 10 hours. Protective substances for thermally modified wood provided similar protection of open thermally modified surfaces of wood from the effects of water. The positive effect of thermal modification on a decrease in the level of water absorption has been established. It has been proven that it is temperature that has a significant effect on such changes. Since the protective coating is also susceptible to photochemical degradation, it is very important to renew it in a timely manner in accordance with the manufacturer's instructions for the pleasant appearance of wood surfaces during external use. The optimal ratio of components in the surface layer of thermally modified wood has been determined, which ensures the fulfillment of the task, namely for a mixture of oil and wax: the density of a wood – 724 kg/m3; oils – 70.0%; wax – 17.5%. Therefore, such treatment is beneficial for the protection and aesthetic appeal of wood products.

scholarly journals Flammability Characteristics of Thermally Modified Meranti Wood Treated with Natural and Synthetic Fire Retardants

Polymers ◽  
2021 ◽  
Vol 13 (13) ◽  
pp. 2160
Author(s):  
Milan Gaff ◽  
Hana Čekovská ◽  
Jiří Bouček ◽  
Danica Kačíková ◽  
Ivan Kubovský ◽  
...  
Keyword(s):  
Burning Rate ◽  
Flame Retardants ◽  
Thermal Modification ◽  
Positive Contribution ◽  
Spearman Correlation ◽  
Chemical Changes ◽  
Combustion Properties ◽  
Flammability Characteristics ◽  
Thermally Modified Wood ◽  
Modified Wood

This paper deals with the effect of synthetic and natural flame retardants on flammability characteristics and chemical changes in thermally treated meranti wood (Shorea spp.). The basic chemical composition (extractives, lignin, holocellulose, cellulose, and hemicelluloses) was evaluated to clarify the relationships of temperature modifications (160 °C, 180 °C, and 210 °C) and incineration for 600 s. Weight loss, burning speed, the maximum burning rate, and the time to reach the maximum burning rate were evaluated. Relationships between flammable properties and chemical changes in thermally modified wood were evaluated with the Spearman correlation. The thermal modification did not confirm a positive contribution to the flammability and combustion properties of meranti wood. The effect of the synthetic retardant on all combustion properties was significantly higher compared to that of the natural retardant.

A review on life cycle assessments of thermally modified wood

Holzforschung ◽  
2020 ◽  
Vol 0 (0) ◽  
Author(s):  
Kévin Candelier ◽  
Janka Dibdiakova
Keyword(s):  
Life Cycle ◽  
Environmental Impacts ◽  
Treated Wood ◽  
Single Step ◽  
Thermal Modification ◽  
Wood Products ◽  
Wood Preservation ◽  
Cumulative Energy ◽  
Thermally Modified Wood ◽  
Cumulative Energy Intake

AbstractThis review compiles various literature studies on the environmental impacts associated with the processes of thermal modification of wood. In wood preservation field, the wood modification by heat is considered as an ecofriendly process due to the absence of any additional chemicals. However, it is challenging to find proper scientific and industrial data that support this aspect. There are still very few complete studies on the life cycle assessment (LCA) and even less studies on the environmental impacts related to wood heat treatment processes whether on a laboratory or on an industrial scales. This comprehensive review on environmental impact assessment emphasizes environmental categories such as dwindling of natural resources, cumulative energy intake, gaseous, solid and liquid emissions occurred by the thermal-treated wood industry. All literature-based data were collected for every single step of the process of wood thermal modification like resources, treatment process, transport and distribution, uses and end of life of treated wood products.

Sign in / Sign up

Export Citation Format

Share Document