Role of Silica Fume in Producing High Strength Self-Compacting Concrete

Author(s):  
Raju Lokhande ◽  
Kirankumar Dindawar
2010 ◽  
Vol 37 (3) ◽  
pp. 420-428 ◽  
Author(s):  
Mehmet Karatas ◽  
Kazim Turk ◽  
Zulfu C. Ulucan

In this study, normal concrete (NC) and four types of self-compacting concrete (SCC), in which cement was partially replaced by 5%, 10%, 15%, and 20% of silica fume (SF), were used to evaluate the effect of SF content on the bond strength of tension lap-spliced bars embedded in NC and SCC specimens. Therefore, 15 full-scale beam specimens (2000 × 300 × 200 mm3) were tested and 20 mm reinforcing bars were used with a 300-mm splice length as tension reinforcement. Each beam was designed with bars spliced in a constant moment region at midspan. It was found that the bond strength of the reinforcement embedded in SCC beams was higher than that of the reinforcement in NC beams, whilst the bond strength increased with increase in the replacement of cement by SF from 5% to 10%. Moreover, the beam specimens produced from SCC containing 5% SF had the highest normalized bond strength of 1.07 followed by SCC beams with 10% SF, 15% SF, NC beams, and 20% SF.


2021 ◽  
Vol 1 (1(57)) ◽  
pp. 17-24
Author(s):  
Vyacheslav Troуan ◽  
Bogdan Kindras

The object of research is high-strength self-compacting concrete, which does not require additional vibration during laying. One of the most problematic issues of high-strength self-compacting concretes is increased cracking, associated with large shrinkage deformations of such concretes and their fragile destruction. A decrease in shrinkage deformations of concrete was established when part of the cement was replaced to mineral additives. This effect is explained by a decrease of the cement content and, accordingly, a decrease of the chemical component of the autogenous shrinkage of concrete, and an increase of the adsorptive binding of capillary moisture by mineral additives, with reduces the physical drying shrinkage of concrete. In this case, the type and dispersion of the used mineral additive can affect to the shrinkage deformations of concrete. A significant decrease in shrinkage deformations when using metakaolin is explained by an increase the amount of ettringite as a result of the reaction of active metakaolin Al2O3 with two-water gypsum of cement. It was found that the replacement of cement to 10 % of mineral additives leads to a decrease in the value of the critical stress intensity factor (SIF), which is compensated by a decrease of the fragility of concrete fracture (an increase of the area of microplastic deformations). At the same time, the type of mineral additive used does not affect to the value of the critical stress intensity factor, but significantly affects to the fragility of fracture of concrete samples. The introduction of 10 % mineral additives (to replace cement) had a positive effect on the retention of flow of self-compacting concrete mixes; the best results according to this criterion were observed when using silica fume, fly ash and limestone. All mineral modifiers, except for silica fume, led to a decrease of the compressive strength of high-strength concretes on all terms of hardening. In the case of the tensile strength of concrete at bending and splitting, with the introduction of silica fume, metakaolin and fly ash, a positive effect was observed compared to the base composition without additives. Comprehensive accounting of the results obtained will allow a reasonable approach to the design of high-strength self-compacting concretes with increased crack resistance.


2018 ◽  
Vol 6 (4) ◽  
Author(s):  
Wahyu Satrio Wicaksono ◽  
Wibowo Wibowo ◽  
Endah Safitri

<p>Beton mutu tinggi yang mampu memadat mandiri <em>(high strength self compacting concrete-HSSCC) </em>merupakan salah satu inovasi beton yang dapat diaplikasikan pada banyak pekerjaan konstruksi. Penambahan s<em>ilica fume </em>yang memiliki butiran lebih halus jika dibandingkan dengan semen bertujuan untuk meningkatkan kuat tekan, sedangkan <em>superplasticizer </em>jenis BASF tipe 8851 digunakan untuk memberikan kinerja yang baik pada beton. Nilai w/b pada penelitian kali ini dijaga konstan sebesar 0,3, kadar <em>superplasticizer </em>adalah 0,8%, dan variasi kadar <em>silica fume </em>sebesar 0%, 8%, 9%, 10% dan 11%. Pengujian beton segar dilakukan dengan 3  metode, yaitu <em>flow table test, l-box test, </em>dan <em>v-funnel test</em>. Dari hasil pengujian tersebut, <em>silica fume </em>dengan kadar 8% memberikan hasil terbaik yang mana memenuhi seluruh persyaratan dari masing-masing metode. Semakin tinggi kadar <em>silica fume </em>maka kinerja beton semakin berkurang. Hal ini terjadi karena sifat <em>silica fume </em>yang menyerap air. Pengujian beton keras dilakukan pada umur 14 hari dan 28 hari. Sementara hasil analisis data menunjukkan bahwa kuat tekan optimum terjadi pada kadar <em>silica fume</em> sebesar 10,21%, sedangkan hasil penelitian menunjukkan bahwa kuat tekan optimum pada umur 28 hari terjadi pada penambahan <em>silica fume </em>sebesar 9% yang memiliki kuat tekan sebesar 67,65 MPa. Sementara dari hasil analisis data menunjukkan bahwa kuat tekan optimum terjadi pada kadar <em>silica fume</em> sebesar 9,37%.</p>


Sign in / Sign up

Export Citation Format

Share Document