An Effect of Current on Mechanical Properties and SEM Characterization of Butt Joint of Aluminium AA6082 Using GTAW

2021 ◽  
pp. 225-237
Author(s):  
Sunil Kumar ◽  
Prabhkiran Kaur ◽  
Amrik Singh
Keyword(s):  
Mechanical Properties ◽  
Butt Joint

scholarly journals Effect of Friction Stir Welding Parameters on the Microstructure and Mechanical Properties of AA2024-T4 Aluminum Alloy

2018 ◽  
Vol 8 (1) ◽  
pp. 2493-2498 ◽  
Author(s):  
A. W. El-Morsy ◽  
M. Ghanem ◽  
H. Bahaitham
Keyword(s):  
Mechanical Properties ◽  
Aluminum Alloy ◽  
Friction Stir Welding ◽  
Cross Section ◽  
High Performance ◽  
Traverse Speed ◽  
Butt Joint ◽  
Welding Parameters ◽  
Friction Stir

In this work, the effects of rotational and traverse speeds on the 1.5 mm butt joint performance of friction stir welded 2024-T4 aluminum alloy sheets have been investigated. Five rotational speeds ranging from 560 to 1800 rpm and five traverse speeds ranging from 11 to 45 mm/min have been employed. The characterization of microstructure and the mechanical properties (tensile, microhardness, and bending) of the welded sheets have been studied. The results reveal that by varying the welding parameters, almost sound joints and high performance welded joints can be successfully produced at the rotational speeds of 900 rpm and 700 rpm and the traverse speed of 35 mm/min. The maximum welding performance of joints is found to be 86.3% with 900 rpm rotational speed and 35 mm/min traverse speed. The microhardness values along the cross-section of the joints show a dramatic drop in the stir zone where the lowest value reached is about 63% of the base metal due to the softening of the welded zone caused by the heat input during joining.

Microstructural and fractographic characterization of B4C-Al cermets tested under dynamic and static loading

1989 ◽  
Vol 47 ◽  
pp. 562-563
Author(s):  
Gyeung Ho Kim ◽  
Mehmet Sarikaya ◽  
D. L. Milius ◽  
I. A. Aksay
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Fracture Toughness ◽  
Static Loading ◽  
Carbon Deposition ◽  
Full Density ◽  
Unique Combination ◽  
Strong Component ◽  
Reaction Products

Cermets are designed to optimize the mechanical properties of ceramics (hard and strong component) and metals (ductile and tough component) into one system. However, the processing of such systems is a problem in obtaining fully dense composite without deleterious reaction products. In the lightweight (2.65 g/cc) B4C-Al cermet, many of the processing problems have been circumvented. It is now possible to process fully dense B4C-Al cermet with tailored microstructures and achieve unique combination of mechanical properties (fracture strength of over 600 MPa and fracture toughness of 12 MPa-m1/2). In this paper, microstructure and fractography of B4C-Al cermets, tested under dynamic and static loading conditions, are described.The cermet is prepared by infiltration of Al at 1150°C into partially sintered B4C compact under vacuum to full density. Fracture surface replicas were prepared by using cellulose acetate and thin-film carbon deposition. Samples were observed with a Philips 3000 at 100 kV.

Characterization of interfaces in CVD-coated nicalon fiber-reinforced SiC

1989 ◽  
Vol 47 ◽  
pp. 556-557
Author(s):  
K.L. More ◽  
R.A. Lowden
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Chemical Vapor ◽  
Chemical Vapor Infiltration ◽  
Frictional Stress ◽  
Fiber Reinforced ◽  
Pull Out ◽  
Carbon Coated ◽  
Fiber Matrix

The mechanical properties of fiber-reinforced composites are directly related to the nature of the fiber-matrix bond. Fracture toughness is improved when debonding, crack deflection, and fiber pull-out occur which in turn depend on a weak interfacial bond. The interfacial characteristics of fiber-reinforced ceramics can be altered by applying thin coatings to the fibers prior to composite fabrication. In a previous study, Lowden and co-workers coated Nicalon fibers (Nippon Carbon Company) with silicon and carbon prior to chemical vapor infiltration with SiC and determined the influence of interfacial frictional stress on fracture phenomena. They found that the silicon-coated Nicalon fiber-reinforced SiC had low flexure strengths and brittle fracture whereas the composites containing carbon coated fibers exhibited improved strength and fracture toughness. In this study, coatings of boron or BN were applied to Nicalon fibers via chemical vapor deposition (CVD) and the fibers were subsequently incorporated in a SiC matrix. The fiber-matrix interfaces were characterized using transmission and scanning electron microscopy (TEM and SEM). Mechanical properties were determined and compared to those obtained for uncoated Nicalon fiber-reinforced SiC.

PREPARATION AND CHARACTERIZATION OF REPROCESSED COMPOSITES OF POLYPROPYLENE REINFORCED BY WOOD FIBERS: PHYSICAL AND MECHANICAL PROPERTIES

2017 ◽  
Author(s):  
Thais Helena Sydenstricker Flores-Sahagun ◽  
Kelly Priscila Agapito ◽  
ROSA MARIA JIMENEZ AMEZCUA ◽  
Felipe Jedyn
Keyword(s):  
Mechanical Properties ◽  
Physical And Mechanical Properties ◽  
Wood Fibers

Emerging Techniques for the Characterization of Nano-Mechanical Properties of Integrated Circuit Components

2008 ◽  
Author(s):  
Nicholas Randall ◽  
Rahul Premachandran Nair
Keyword(s):  
Mechanical Properties ◽  
Quality Control ◽  
Integrated Circuits ◽  
Integrated Circuit ◽  
Manufacturing Process ◽  
Solder Bumps ◽  
Initial Work ◽  
Circuit Components ◽  
Materials Used

Abstract With the growing complexity of integrated circuits (IC) comes the issue of quality control during the manufacturing process. In order to avoid late realization of design flaws which could be very expensive, the characterization of the mechanical properties of the IC components needs to be carried out in a more efficient and standardized manner. The effects of changes in the manufacturing process and materials used on the functioning and reliability of the final device also need to be addressed. Initial work on accurately determining several key mechanical properties of bonding pads, solder bumps and coatings using a combination of different methods and equipment has been summarized.

Fabrication and Characterization of Biocomposite Using Grewia Optiva Fibre (i.e. Bhimal) Reinforced Polyvinyl Alcohol (PVA)

2015 ◽  
Vol 1105 ◽  
pp. 51-55 ◽  
Author(s):  
K.M. Gupta ◽  
Kishor Kalauni
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Natural Fibre ◽  
Fabrication Method ◽  
View Point ◽  
Engineering Material ◽  
Fibre Composites ◽  
Grewia Optiva ◽  
Fabrication And Characterization

Bhimal fibres are quite a newer kind of bio-degradable fibres. They have never been heard before in literatures from the view point of their utility as engineering material. These fibres have been utilized for investigation of their properties. Characterization of this fibre is essential to determine its properties for further use as reinforcing fibre in polymeric, bio-degradable and other kinds of matrix. With this objective, the fabrication method and other mechanical properties of Bhimal-reinforced-PVA biocomposite have been discussed. The stress-strain curves and load-deflection characteristics are obtained. The tensile, compressive, flexure and impact strengths have been calculated. The results are shown in tables and graphs. The results obtained are compared with other existing natural fibre biocomposites. From the observations, it has been concluded that the tensile strength of Bhimal-reinforced-PVA biocomposite is higher than other natural fibre composites. Hence these can be used as reinforcement to produce much lighter weight biocomposites.

Elaboration and Characterization of the Properties of Refractory Cr Base Alloys

2010 ◽  
Vol 72 ◽  
pp. 46-52 ◽  
Author(s):  
Laurent Royer ◽  
Stéphane Mathieu ◽  
Christophe Liebaut ◽  
Pierre Steinmetz
Keyword(s):  
Mechanical Properties ◽  
Melting Point ◽  
Molten Glass ◽  
Energy Production ◽  
Creep Properties ◽  
Refractory Alloys ◽  
Industrial Use ◽  
Kinetics Of ◽  
Selection Of

For energy production and also for the glass industry, finding new refractory alloys which could permit to increase the process temperatures to 1200°C or more is a permanent challenge. Chromium base alloys can be good candidates, considering the melting point of Cr itself, and also its low corrosion rate in molten glass. Two families of alloys have been studied for this purpose, Cr-Mo-W and Cr-Ta-X alloys (X= Mo, Si..). A finer selection of compositions has been done, to optimize their chemical and mechanical properties. Kinetics of HT oxidation by air, of corrosion by molten glass and also creep properties of several alloys have been measured up to 1250°C. The results obtained with the best alloys (Cr-Ta base) give positive indications as regards the possibility of their industrial use.

Sign in / Sign up

Export Citation Format

Share Document