Analyzing rotor-blade vibrations in gas-turbine units

1983 ◽  
Vol 15 (5) ◽  
pp. 636-642
Author(s):  
E. A. Igumentsev
Keyword(s):  
Gas Turbine ◽  
Rotor Blade ◽  
Blade Vibrations

Heat Transfer Coefficients and Film Cooling Effectiveness on the Squealer Tip of a Gas Turbine Blade

2003 ◽  
Vol 125 (4) ◽  
pp. 648-657 ◽  
Author(s):  
Jae Su Kwak ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Film Cooling ◽  
Rotor Blade ◽  
Transfer Coefficients ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Heat Transfer Coefficients ◽  
Blowing Ratio

Experimental investigations were performed to measure the detailed heat transfer coefficients and film cooling effectiveness on the squealer tip of a gas turbine blade in a five-bladed linear cascade. The blade was a two-dimensional model of a first stage gas turbine rotor blade with a profile of the GE-E3 aircraft gas turbine engine rotor blade. The test blade had a squealer (recessed) tip with a 4.22% recess. The blade model was equipped with a single row of film cooling holes on the pressure side near the tip region and the tip surface along the camber line. Hue detection based transient liquid crystals technique was used to measure heat transfer coefficients and film cooling effectiveness. All measurements were done for the three tip gap clearances of 1.0%, 1.5%, and 2.5% of blade span at the two blowing ratios of 1.0 and 2.0. The Reynolds number based on cascade exit velocity and axial chord length was 1.1×106 and the total turning angle of the blade was 97.9 deg. The overall pressure ratio was 1.2 and the inlet and exit Mach numbers were 0.25 and 0.59, respectively. The turbulence intensity level at the cascade inlet was 9.7%. Results showed that the overall heat transfer coefficients increased with increasing tip gap clearance, but decreased with increasing blowing ratio. However, the overall film cooling effectiveness increased with increasing blowing ratio. Results also showed that the overall film cooling effectiveness increased but heat transfer coefficients decreased for the squealer tip when compared to the plane tip at the same tip gap clearance and blowing ratio conditions.

scholarly journals Heat Transfer and Flow on the Squealer Tip of a Gas Turbine Blade

2000 ◽  
Author(s):  
Gm S. Azad ◽  
Je-Chin Han ◽  
Robert J. Boyle
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbine ◽  
Rotor Blade ◽  
Static Pressure ◽  
Cavity Surface ◽  
Edge Region ◽  
Blade Tip ◽  
The Heat Transfer Coefficient

Experimental investigations are performed to measure the detailed heat transfer coefficient and static pressure distributions on the squealer tip of a gas turbine blade in a five-bladed stationary linear cascade. The blade is a 2-dimensional model of a modern first stage gas turbine rotor blade with a blade tip profile of a GE-E3 aircraft gas turbine engine rotor blade. A squealer (recessed) tip with a 3.77% recess is considered here. The data on the squealer tip are also compared with a flat tip case. All measurements are made at three different tip gap clearances of about 1%, 1.5%, and 2.5% of the blade span. Two different turbulence intensities of 6.1% and 9.7% at the cascade inlet are also considered for heat transfer measurements. Static pressure measurements are made in the mid-span and near-tip regions, as well as on the shroud surface opposite to the blade tip surface. The flow condition in the test cascade corresponds to an overall pressure ratio of 1.32 and an exit Reynolds number based on the axial chord of 1.1×106. A transient liquid crystal technique is used to measure the heat transfer coefficients. Results show that the heat transfer coefficient on the cavity surface and rim increases with an increase in tip clearance. The heat transfer coefficient on the rim is higher than the cavity surface. The cavity surface has a higher heat transfer coefficient near the leading edge region than the trailing edge region. The heat transfer coefficient on the pressure side rim and trailing edge region is higher at a higher turbulence intensity level of 9.7% over 6.1% case. However, no significant difference in local heat transfer coefficient is observed inside the cavity and the suction side rim for the two turbulence intensities. The squealer tip blade provides a lower overall heat transfer coefficient when compared to the flat tip blade.

Flow Interactions Between Shrouded Power Turbine and Nonaxisymmetric Exhaust Volute for Marine Gas Turbines

2017 ◽  
Author(s):  
Jie Gao ◽  
Feng Lin ◽  
Xiying Niu ◽  
Qun Zheng ◽  
Guoqiang Yue ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Rotor Blade ◽  
Exhaust System ◽  
Computational Domain ◽  
Local Flow ◽  
Power Turbine ◽  
Flow Interactions ◽  
Shrouded Rotor ◽  
Turbine Exhaust

The marine gas turbine exhaust volute is an important component that connects a power turbine and an exhaust system, and it is of great importance to the overall performance of the gas turbine. Gases exhausted from the power turbine are expanded and deflected 90 degrees in the exhaust volute, and then discharge radially into the exhaust system. The flows in the power turbine and the nonaxisymmetric exhaust volute are closely coupled and inherently unsteady. The flow interactions between the power turbine and the exhaust volute have a significant influence on the shrouded rotor blade aerodynamic forces. However, the interactions have not been taken into account properly in current power turbine design approaches. The present study aims to investigate the flow interactions between the last stage of a shrouded power turbine and the nonaxisymmetric exhaust volute with struts. Special attention is given to the coupled aerodynamics and pressure response studies. This work was carried out using coupled computational fluid dynamics (CFD) simulations with the computational domain including a stator vane, 76 shrouded rotor blades, 9 struts and an exhaust volute. Three-dimensional (3D) unsteady and steady Reynolds-averaged Navier-Stokes (RANS) solutions in conjunction with a Spalart-Allmaras turbulence model are utilized to investigate the aerodynamic characteristics of shrouded rotors and an exhaust volute using a commercial CFD software ANSYS Fluent 14.0. The asymmetric flow fields are analyzed in detail; as are the unsteady pressures on the shrouded rotor blade. In addition, the unsteady total pressures at the volute outlet is also analyzed without consideration of the upstream turbine effects. Results show that the flows in the nonaxisymmetric exhaust volute are inherently unsteady; for the studied turbine-exhaust configuration the nonaxisymmetric back-pressure induced by the downstream volute leads to the local flow varying for each shrouded blade and low frequency fluctuations in the blade force. Detailed results from this investigation are presented and discussed in this paper.

Back Flow in Turbines of Nuclear Closed-Cycle Gas Turbine Plants in Case of Circuit Pipe Rupture

1975 ◽  
Vol 97 (2) ◽  
pp. 189-194 ◽  
Author(s):  
K. Bammert ◽  
P. Zehner
Keyword(s):  
Gas Turbine ◽  
Rotor Blade ◽  
Back Flow ◽  
Blade Tip ◽  
Stator Blade ◽  
Flow Through ◽  
High Temperature Reactor ◽  
Turbine Cascades ◽  
Characteristic Features ◽  
Safety Considerations

For operation of a gas turbine in single-cycle arrangement with a high-temperature reactor, rupture of a main circuit pipe has to be included in the safety considerations. In the event of such an accident there may be a back flow through the turbo machines or a forward flow up to the choking limit. This paper is a report on tests carried out in a two-dimensional cascade wind tunnel on turbine cascades under back flow conditions. By the example of three selected representative cascades the characteristic features in turbine cascades with back flow are discussed. These cascades are a rotor blade tip section with aerofoil-like profiles and a wide pitch, a stator blade or rotor blade mean section with an usual deflection and a rotor blade root section with a narrow pitch and a large deflection.

scholarly journals Heat Transfer and Pressure Distributions on a Gas Turbine Blade Tip

2000 ◽  
Vol 122 (4) ◽  
pp. 717-724 ◽  
Author(s):  
Gm. S. Azad ◽  
Je-Chin Han ◽  
Shuye Teng ◽  
Robert J. Boyle
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Gas Turbine ◽  
Turbine Blade ◽  
Turbulence Intensity ◽  
Rotor Blade ◽  
Static Pressure ◽  
Pressure Distributions ◽  
Blade Tip

Heat transfer coefficient and static pressure distributions are experimentally investigated on a gas turbine blade tip in a five-bladed stationary linear cascade. The blade is a two-dimensional model of a first-stage gas turbine rotor blade with a blade tip profile of a GE-E3 aircraft gas turbine engine rotor blade. The flow condition in the test cascade corresponds to an overall pressure ratio of 1.32 and exit Reynolds number based on axial chord of 1.1×106. The middle 3-blade has a variable tip gap clearance. All measurements are made at three different tip gap clearances of about 1, 1.5, and 2.5 percent of the blade span. Heat transfer measurements are also made at two different turbulence intensity levels of 6.1 and 9.7 percent at the cascade inlet. Static pressure measurements are made in the midspan and the near-tip regions as well as on the shroud surface, opposite the blade tip surface. Detailed heat transfer coefficient distributions on the plane tip surface are measured using a transient liquid crystal technique. Results show various regions of high and low heat transfer coefficient on the tip surface. Tip clearance has a significant influence on local tip heat transfer coefficient distribution. Heat transfer coefficient also increases about 15–20 percent along the leakage flow path at higher turbulence intensity level of 9.7 over 6.1 percent. [S0889-504X(00)00404-9]

scholarly journals The Design and Evaluation of a 14 Stage, 16:1 Pressure Ratio Compressor for an Industrial Gas Turbine

1996 ◽  
Author(s):  
Mohammad R. Saadatmand
Keyword(s):  
Experimental Data ◽  
Gas Turbine ◽  
Rotor Blade ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Operating Conditions ◽  
Suction Surface ◽  
Design Intent ◽  
Flow Through ◽  
Industrial Gas Turbine

The aerodynamic design process leading to the production configuration of a 14 stage, 16:1 pressure ratio compressor for the Taurus 70 gas turbine is described. The performance of the compressor is measured and compared to the design intent. Overall compressor performance at the design condition was found to be close to design intent. Flow profiles measured by vane mounted instrumentation are presented and discussed. The flow through the first rotor blade has been modeled at different operating conditions using the Dawes (1987) three-dimensional viscous code and the results are compared to the experimental data. The CFD prediction agreed well with the experimental data across the blade span, including the pile up of the boundary layer on the corner of the hub and the suction surface. The rotor blade was also analyzed with different grid refinement and the results were compared with the test data.

scholarly journals Aerodynamic Design and Testing of an Improved 1st Stage Compressor Rotor for a Heavy Duty Gas Turbine

1981 ◽  
Author(s):  
I. Ispas ◽  
H. J. Zollinger
Keyword(s):  
Gas Turbine ◽  
Rotor Blade ◽  
Aerodynamic Design ◽  
Heavy Duty ◽  
High Loss ◽  
Compressor Rotor ◽  
Performance Map ◽  
Computer Codes ◽  
Heavy Duty Gas Turbine ◽  
Design And Testing

To evaluate the potential of the compressor of Sulzer’s Typ 3 gas turbine, a series of engine tests was analyzed with two computer codes. The comparison between measured and calculated performance map are given in the paper. The design goal was to find modifications, which can be applied easily to already operating engines. The simplest option-increase of shaft speed with the existing blades-would have caused high loss due to increased tip Mach number. The calculation revealed, that a newly designed first rotor blade is an appropriate modification to increase massflow and efficiency. No further change is required, because the calculations indicate, that all subsequent stages operate at near optimum incidence. The calculations were confirmed experimentally. The paper presents the new rotor blade and its influence on the compressor calculated and measured performance.

scholarly journals Failure Analysis of Gas Turbine Rotary Blade

2017 ◽  
pp. 1-6
Keyword(s):  
Finite Element ◽  
Gas Turbine ◽  
Rotor Blade ◽  
Rotor Blades ◽  
Centrifugal Forces ◽  
Analysis Software ◽  
Two Stage ◽  
Element Analysis ◽  
Finite Element Software ◽  
Super Alloy

In the present work the first stage rotor blade of a two- stage gas turbine has been analyzed for structural, thermal using ANSYS 9.0, which is a powerful Finite Element Software. In the present work, the first stage rotor blade of the gas turbine has been analyzed for the mechanical and radial elongations resulting from the tangential, axial and centrifugal forces. The gas forces namely tangential, axial were determined by constructing velocity triangles at inlet and exist of rotor blades. The rotor blade was then analyzed using ANSYS 9.0 for the temperature distribution. The material of the blade was specified as N155 but its properties were not given. This material is an iron based super alloy and structural and thermal properties at gas room and room temperatures. The turbine blade along with the groove is considered for the static, thermal, modal analysis. The first stage rotor blade of a two-stage gas turbine has been analyzed for structural, thermal using ANSYS 9.0 Finite Element Analysis software.

Rotor Blade Vibration Measurement on Aero Gas Turbine Engines

2020 ◽  
pp. 263-273
Author(s):  
T. Devi Priya ◽  
Sunil Kumar ◽  
Devendra Pratap ◽  
S. Shylaja ◽  
T. N. Satish ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Rotor Blade ◽  
Vibration Measurement ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Blade Vibration
Sign in / Sign up

Export Citation Format

Share Document