scholarly journals Characterization of microstructure and selected properties of SnSbCu alloy after FSP

2021 ◽  
Author(s):  
Joanna Hrabia-Wiśnios ◽  
Beata Leszczyńska-Madej ◽  
Marcin Madej ◽  
Aleksandra Węglowska
Keyword(s):  
Flexural Strength ◽  
Diffraction Method ◽  
Compression Tests ◽  
X Ray Diffraction ◽  
Linear Speed ◽  
X Ray ◽  
Friction Stir ◽  
Before And After ◽  
Bearing Alloy

AbstractThe paper presents the results of research on the microstructure and selected mechanical properties of the SnSbCu-bearing alloy after friction stir processing (FSP). The Whorl tool was used for modification; the process was carried out using two rotational speeds of the tool: 280 and 450 RPM and a constant linear speed of 355 mm/min. Microstructure studies were performed employing the techniques of light microscopy and scanning electron microscopy along with analysis of the chemical composition of micro-areas. Additionally, the phase composition was investigated by means of the X-ray diffraction method and statistical analysis of the precipitates present in the investigated alloy. In addition, hardness, flexural strength, and uniaxial compression tests were performed before and after FSP modification. It was proved that using FSP to modify the SnSbCu alloy promotes refinement and homogenization of the microstructure, as well as improvement of the flexural strength, whereas no changes in the hardness level were found.

scholarly journals Characterization Of Microstructure And Selected Properties of SnSbCu Alloy After FSP

2021 ◽  
Author(s):  
Joanna Hrabia-Wiśnios ◽  
Beata Leszczyńska-Madej ◽  
Marcin Madej ◽  
Aleksandra Węglowska
Keyword(s):  
Flexural Strength ◽  
Diffraction Method ◽  
Compression Tests ◽  
X Ray Diffraction ◽  
Linear Speed ◽  
X Ray ◽  
Friction Stir ◽  
Before And After ◽  
Bearing Alloy

Abstract The paper presents the results of research on the microstructure and selected mechanical properties of the SnSbCu bearing alloy after friction stir processing (FSP). The Whorl tool was used for modification; the process was carried out using two rotational speeds of the tool: 280 and 450 RPM and a constant linear speed of 355 mm/min. Microstructure studies were performed employing the techniques of light microscopy and scanning electron microscopy along with analysis of the chemical composition of micro-areas. Additionally, the phase composition was investigated by means of the X-ray diffraction method and statistical analysis of the precipitates present in the investigated alloy. In addition, hardness, flexural strength and uniaxial compression tests were performed before and after FSP modification. It was proved that using FSP to modify the SnSbCu alloy promotes refinement and homogenization of the microstructure, as well as improvement of the flexural strength, whereas no changes in the hardness level were found.

XRD investigation of thermal degradation of some gamma-irradiated polyethylene terephthalate samples

2019 ◽  
Vol 33 (12) ◽  
pp. 1950111 ◽  
Author(s):  
Mihai Todica ◽  
Zoltan Kovacs-Krauss ◽  
Carmen Niculaescu ◽  
Marieta Mureşan-Pop
Keyword(s):  
Thermal Treatment ◽  
Polyethylene Terephthalate ◽  
Structural Changes ◽  
Diffraction Method ◽  
Resonance Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Before And After ◽  
Gamma Irradiated ◽  
Different Doses

The modification of local structure of some commercial polyethylene terephthalate (PET) samples, gamma irradiated at different doses, was investigated by X-ray diffraction method before and after thermal treatment. Before the thermal treatment, the samples exposed to different doses of gamma radiations, does not show noticeable structural changes. However, the gamma exposure affects the thermal behavior of samples submitted to melting–cooling process. These modifications have been highlighted by X-ray diffraction, and confirmed also by thermal analysis and electron spin resonance spectroscopy.

Preparation and Characterization of Clays from Different Areas in Ban Bo Suak, Nan Province, Thailand

2015 ◽  
Vol 659 ◽  
pp. 127-131
Author(s):  
Usanee Malee ◽  
Sakdiphon Thiansem
Keyword(s):  
Clay Sample ◽  
X Ray Diffraction ◽  
Scientific Process ◽  
Quartz Content ◽  
Xrd Pattern ◽  
X Ray ◽  
Kiln Site ◽  
Before And After ◽  
Tone Color

The scientific process was used to explain characterization and physical properties of the clay sample close to the ancient Nan kiln site. These samples were obtained from JQA, FQB, PQC and NQD. X-ray diffraction (XRD) and X-ray fluorescence (XRF) technique were used to determine the chemical composition and phase transformation before and after fired at 800-1250 °C. XRF result was confirmed that all clay samples mainly contained SiO2(>80 wt. %) XRD pattern indicated that quartz was the majority of phase in the all of them. High amount of Fe2O3(>1.6 wt. %) was related to the red-brown tone color. The clay sample could be fired up to 1280 °C without wrapping behavior; it was found that FQB clay had the highest firing resistance due to the maximum quartz content.

Characterization of silica polymorphs in kaolins by X-ray diffraction before and after phosphoric acid digestion and thermal treatment

2005 ◽  
Vol 552 (1-2) ◽  
pp. 201-206 ◽  
Author(s):  
Sibel Kahraman ◽  
Müşerref Önal ◽  
Yüksel Sarıkaya ◽  
İhsan Bozdoğan
Keyword(s):  
Thermal Treatment ◽  
Phosphoric Acid ◽  
Acid Digestion ◽  
X Ray Diffraction ◽  
X Ray ◽  
Before And After

Synthesis and Characterization of Zinc Doped Hydroxyapatite for Bone Substitute Applications

2014 ◽  
Vol 660 ◽  
pp. 942-946
Author(s):  
Mohamad Firdaus Abdul Wahid ◽  
C.M. Mardziah ◽  
Koay Mei Hyie ◽  
N.R. Nik Roselina
Keyword(s):  
Crystal Size ◽  
Diffraction Method ◽  
Lattice Parameters ◽  
Phase Changes ◽  
Precipitation Method ◽  
Zinc Ions ◽  
Crystal Shape ◽  
X Ray Diffraction ◽  
X Ray

Hydroxyapatite was prepared by using precipitation method. The substitution of zinc ions in hydroxyapatite structure was studied by several characterization techniques. Several concentration of zinc ions were substituted into hydroxyapatite. Characterization technique such as X-ray diffraction method was used to study the phase changes and the lattice parameters with the addition of zinc. Field emission scanning electron microscopy was used to examine the influence of zinc on the crystal size and the morphology of the as-synthesized powders. Based on X-ray diffraction result, the addition of zinc affects the lattice parameters and phase. The result showed that zinc ions were substituted in the structure. As zinc substitution increased, the lattice parameters a and c decreased. The crystal shape of hydroxyapatite without zinc ions was regular shapes while hydroxyapatite with zinc ions was irregular and also tends to agglomerates with single particle was calculated about 28 - 34 nm .

scholarly journals Growth and Characterization of Pure and Doped L-Alanine Tartrate Single Crystals

2013 ◽  
Vol 2013 ◽  
pp. 1-5 ◽  
Author(s):  
K. Rajesh ◽  
B. Milton Boaz ◽  
P. Praveen Kumar
Keyword(s):  
Single Crystals ◽  
Vickers Microhardness ◽  
Diffraction Method ◽  
Dielectric Studies ◽  
X Ray Diffraction ◽  
X Ray ◽  
Cell Parameters ◽  
Ft Ir ◽  
Ft Ir Spectroscopy

Single crystals of pure and Lanthanum doped L-Alanine Tartrate were grown by slow evaporation method. The cell parameters were determined using single crystal X-ray diffraction method. To improve the physical properties of the LAT crystal, Lanthanum dopant was added by 2 mol%. ICP studies confirm the presence of Lanthanum in the grown LAT crystal. Transparency range of the crystal was determined using UV-VIS-NIR spectrophotometer. The functional groups of pure and doped LAT crystals were analyzed by FT-IR spectroscopy. Using Vickers microhardness tester, mechanical strength of the material was found. Dielectric studies of pure and doped LAT single crystals were carried out. The doped LAT crystal is found to have efficiency higher than that of pure LAT crystal.

An Investigation and Characterization of Monkeypod Tree Flower Particulates Filled PLA Composites

2021 ◽  
Author(s):  
Balaji Ayyanar Chninnappan ◽  
K. Marimuthu ◽  
C. Bharathiraj ◽  
B. Gayathri ◽  
S. K. Pradep Mohan
Keyword(s):  
Tensile Strength ◽  
Flexural Strength ◽  
Thermo Gravimetric Analysis ◽  
Injection Molding Process ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
Molding Process ◽  
X Ray ◽  
Samanea Saman

Abstract Samanea saman (SS) flower particulates were filled in Polylactic acid (PLA) composites were fabricated with different 0, 10, and 20 wt. % through the injection molding process. The elemental composition and morphology of SS PLA composites were studied through FESEM and Energy Dispersive X-ray analysis. Thermal stability of the SS PLA composites specimens was carried out through Thermo Gravimetric Analysis (TGA) and Differential Scanning Calorimeter (DSC). Crystal orientations studied through X-Ray Diffraction (XRD) showed the presence of the orthorhombic SS particulates. The properties of the composites were investigated such as tensile strength, compressive strength, flexural strength, and Shore D Hardness. It was found that 20 wt. % of SS filled PLA composites has a superior tensile strength of 43.76 MPa, the compression strength of 37.94 MPa, the flexural strength of 72.47 MPa, and Shore D Hardness of 80.1 SHN than pure PLA. SS particulates-filled PLA composites would be used for low-strength applications.

Residual stress characterization of diamond-like carbon coatings by an X-ray diffraction method

1999 ◽  
Vol 122 (2-3) ◽  
pp. 219-224 ◽  
Author(s):  
Sam Zhang ◽  
Hong Xie ◽  
Xianting Zeng ◽  
Peter Hing
Keyword(s):  
Residual Stress ◽  
Diffraction Method ◽  
Diamond Like Carbon ◽  
X Ray Diffraction ◽  
Carbon Coatings ◽  
X Ray

scholarly journals Characterization of CaTi0.9Fe0.1O3/La0.98Mg0.02NbO4 composite

Open Physics ◽  
2013 ◽  
Vol 11 (2) ◽  
Author(s):  
Aleksandra Mielewczyk-Gryn ◽  
Tomasz Lendze ◽  
Katarzyna Gdula-Kasica ◽  
Piotr Jasinski ◽  
Andrzej Krupa ◽  
...  
Keyword(s):  
Sintering Temperature ◽  
Perovskite Phase ◽  
Pyrochlore Phase ◽  
Diffraction Method ◽  
Total Conductivity ◽  
X Ray Diffraction ◽  
X Ray ◽  
Temperature Interaction ◽  
Composite Samples

AbstractA composite of CaTi0.9Fe0.1O3 and electrolyte material, i.e. magnesium doped La0.98Mg0.02NbO4 was prepared and studied. The phase content and the sample microstructure was examined by an X-ray diffraction method and scanning electron microscopy. EDS measurements were done both for composite samples and the diffusion couple. The electrical properties were studied by four terminal DC method. The high-temperature interaction between the two components of the composite has been observed. It has been suggested that lanthanum diffused into the perovskite phase and substituted for calcium whereas calcium and niobium formed the Ca2Nb2O7 pyrochlore phase. At 1500°C very large crystallites of the pyrochlore were observed. Regardless of strong interaction between the composite components, its total conductivity was weakly dependent on the sintering temperature.

Sign in / Sign up

Export Citation Format

Share Document