The Interplay of In Situ Stress Ratio and Transverse Isotropy in the Rock Mass on Prestressed Concrete-Lined Pressure Tunnels

2016 ◽  
Vol 49 (11) ◽  
pp. 4371-4392 ◽  
Author(s):  
T. D. Y. F. Simanjuntak ◽  
M. Marence ◽  
A. J. Schleiss ◽  
A. E. Mynett
Keyword(s):  
Rock Mass ◽  
Prestressed Concrete ◽  
Stress Ratio ◽  
Transverse Isotropy ◽  
In Situ Stress

Analysis of TBM Tunnel Behavior in Jointed Rock Mass

2011 ◽  
Vol 90-93 ◽  
pp. 2033-2036 ◽  
Author(s):  
Jin Shan Sun ◽  
Hong Jun Guo ◽  
Wen Bo Lu ◽  
Qing Hui Jiang
Keyword(s):  
Rock Mass ◽  
Numerical Models ◽  
Jointed Rock ◽  
In Situ Stress ◽  
Jointed Rock Mass ◽  
Joint Orientation ◽  
Joint Spacing ◽  
Factors Affecting ◽  
Dip Angle

The factors affecting the TBM tunnel behavior in jointed rock mass is investigated. In the numerical models the concrete segment lining of TBM tunnel is concerned, which is simulated as a tube neglecting the segment joint. And the TBM tunnel construction process is simulate considering the excavation and installing of the segment linings. Some cases are analyzed with different joint orientation, joint spacing, joint strength and tunnel depth. The results show that the shape and areas of loosing zones of the tunnel are influenced by the parameters of joint sets and in-situ stress significantly, such as dip angle, spacing, strength, and the in-situ stress statement. And the stress and deformation of the tunnel lining are influenced by the parameters of joint sets and in-situ stress, too.

Study on Deformation and Damage of Rock Mass Subject to High In Situ Stress by Using a Elastoplastic Damage Model and Considering the Impact of Weak Planes

2013 ◽  
Vol 838-841 ◽  
pp. 705-709
Author(s):  
Yun Hao Yang ◽  
Ren Kun Wang
Keyword(s):  
Rock Mass ◽  
Large Scale ◽  
Damage Model ◽  
Back Analysis ◽  
In Situ Stress ◽  
Surrounding Rock ◽  
High In Situ Stress ◽  
Underground Caverns ◽  
The Impact

Large scale underground caverns are under construction in high in-situ stress field at Houziyan hydropower station. To investigate deformation and damage of surrounding rock mass, a elastoplastic orthotropic damage model capable of describing induced orthotropic damage and post-peak behavior of hard rock is used, together with a effective approach accounting for the presence of weak planes. Then a displacement based back analysis was conducted by using the measured deformation data from extensometers. The computed displacements are in good agreement with the measured ones at most of measurement points, which confirm the validities of constitutive model and numerical simulation model. The result of simulation shows that damage of surrounding rock mass is mainly dominated by the high in-situ stress rather than the weak planes and heavy damage occur at the cavern shoulders and side walls.

The Application of Hydraulic Fracturing in Storage Projects of Liquefied Petroleum Gas

2006 ◽  
Vol 306-308 ◽  
pp. 1509-1514 ◽  
Author(s):  
Jing Feng ◽  
Qian Sheng ◽  
Chao Wen Luo ◽  
Jing Zeng
Keyword(s):  
Rock Mass ◽  
Hydraulic Fracturing ◽  
Stress Measurement ◽  
Test Procedure ◽  
In Situ Stress ◽  
Test System ◽  
Petroleum Engineering ◽  
Liquefied Petroleum Gas

It is very important to study the pristine stress field in Civil, Mining, Petroleum engineering as well as in Geology, Geophysics, and Seismology. There are various methods of determination of in-situ stress in rock mass. However, hydraulic fracturing techniques is the most convenient method to determine and interpret the test results. Based on an hydraulic fracturing stress measurement campaign at an underground liquefied petroleum gas storage project which locates in ZhuHai, China, this paper briefly describes the various uses of stress measurement, details of hydraulic fracturing test system, test procedure adopted and the concept of hydraulic fracturing in arriving at the in-situ stresses of the rock mass.

scholarly journals Rock Mass Behavior under Tunnel Widening in Asymmetric and Symmetric Modes Considering Different Shapes and Parametric Conditions

Geosciences ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 518
Author(s):  
Babar Khan ◽  
Syed Muhammad Jamil ◽  
Jung Joo Kim ◽  
Turab H. Jafri ◽  
Jonguk Kim
Keyword(s):  
Rock Mass ◽  
In Situ Stress ◽  
Design Parameters ◽  
Tunnel Widening ◽  
Tunnel Support ◽  
Mass Behavior ◽  
Rock Types ◽  
The Difference ◽  
Support Conditions

To accommodate traffic volume on roads due to ever-increasing population growth, the widening of highways and motorways is in high demand. Nevertheless, the widening of tunnels on these road networks is quite complex due to the presence of numerous rock types, in situ stress, and different widening modes. To overcome these complexities, eight different tunnel shapes were simulated under varying support conditions for asymmetric and symmetric widening. It was found that the tunnels with a round shape, such as horseshoe and semicircular with flatbed, are more effective for asymmetric widening, whereas the provision of a rounded invert in these shapes can reverse the widening option to symmetric. Furthermore, an insignificant effect of the difference in asymmetric and symmetric widening of regular tunnel shapes, such as box, rectangular, and semi-elliptical, was found. A full factorial design statistical analysis confirmed the decrease in tunnel deformation by using various tunnel support systems and showed a significant deformation difference according to monitoring locations at the tunnel periphery. The deformation difference in the case of both tunnel widening modes was also analyzed according to different design parameters. This study provides a comprehensive understanding of rock mass behavior when the widening of any underground opening is carried out.

scholarly journals Numerical Investigation of a Hydrosplitting Fracture and Weak Plane Interaction Using Discrete Element Modeling

Water ◽  
2020 ◽  
Vol 12 (2) ◽  
pp. 535
Author(s):  
Shuaiqi Liu ◽  
Fengshan Ma ◽  
Haijun Zhao ◽  
Jie Guo ◽  
Xueliang Duan ◽  
...  
Keyword(s):  
Shear Stress ◽  
Principal Stress ◽  
Stress Ratio ◽  
Water Pressure ◽  
Maximum Shear Stress ◽  
Water Inrush ◽  
Discrete Element ◽  
Maximum Principal Stress ◽  
In Situ Stress

Water inrush caused by hydrosplitting is an extremely common disaster in the engineering of underground tunnels. In this study, the propagation of fluid-driven fractures based on an improved discrete element fluid-solid coupling method was modeled. First, the interactions between hydrosplitting fractures (HFs) and preexisting weak planes (WPs) with different angles were simulated considering water pressure in the initial fracture. Second, the influence of the in situ stress ratio and the property of WPs were analyzed, and corresponding critical pressure values of different interactions were calculated. Lastly, the maximum principal stress and maximum shear stress variation inside the pieces were reproduced. The following conclusions can be drawn: (1) Five different types of interaction modes between HFs and natural WPs were obtained, prone to crossing the WPs under inclination of 90°. (2) The initiation pressure value decreased with an increased in situ stress ratio, and the confining stress status had an effect on the internal principal stress. (3) During HFs stretching in WPs with a high elastic modulus, the value of the maximum principal stress was low and rose slowly, and the maximum shear stress value was smaller. Through comprehensive analysis, the diversity of the principal stress curves is fundamentally determined by the interaction mode between HFs and WPs, which are influenced by the variants mentioned in the paper. The analysis provides a better guideline for understanding the failure mechanism of water gushing out of deep buried tunnel construction and cracking seepage of high head tunnels.

Dynamic response of rock mass induced by the transient release of in-situ stress

2012 ◽  
Vol 53 ◽  
pp. 129-141 ◽  
Author(s):  
Wenbo Lu ◽  
Jianhua Yang ◽  
Peng Yan ◽  
Ming Chen ◽  
Chuangbing Zhou ◽  
...  
Keyword(s):  
Rock Mass ◽  
Dynamic Response ◽  
In Situ Stress

Microseism Induced by Transient Release of In Situ Stress During Deep Rock Mass Excavation by Blasting

2012 ◽  
Vol 46 (4) ◽  
pp. 859-875 ◽  
Author(s):  
Jianhua Yang ◽  
Wenbo Lu ◽  
Ming Chen ◽  
Peng Yan ◽  
Chuangbing Zhou
Keyword(s):  
Rock Mass ◽  
In Situ Stress ◽  
Deep Rock Mass ◽  
Deep Rock

scholarly journals Comparative Study of the Excavation Damage and Rockburst of the Deeply Buried Jinping II Diversion Tunnels Using a TBM and the Drilling-Blasting Method

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Jing Yang ◽  
Xing-Guo Yang ◽  
Jia-Wen Zhou ◽  
Yong Liu ◽  
Bao-Shun Dong ◽  
...  
Keyword(s):  
Rock Mass ◽  
Stress Concentration ◽  
High Stress ◽  
Tunnel Boring Machine ◽  
In Situ Stress ◽  
Surrounding Rock ◽  
High In Situ Stress ◽  
Damaged Zone ◽  
Blasting Method

The rock mass failure induced by high in-situ stresses during the excavation of deep diversion tunnels is one of the key problems in the construction of the Jinping II Hydropower Station. Based on the results of acoustic wave tests and rockburst statistical analysis conducted, this study focuses on the excavation damaged zone (EDZ) and rockburst events in the Jinping II diversion tunnels excavated using the tunnel boring machine (TBM) method and the drilling-blasting method. The unloading failure mechanism and the rockburst induced by the two different excavation methods were compared and analyzed. The results indicate that, due to the different stress adjustment processes, the degree of damage to the surrounding rock mass excavated using the drilling-blasting method was more serious than that using the TBM method. The EDZ induced by the TBM was usually distributed evenly along the edge of the excavation surface. While, the drilling-blasting method was more likely to cause stress concentration, resulting in a deeper EDZ in local areas. However, the TBM excavation method can cause other problems in high in-situ stress areas, such as strong rockbursts. The drilling-blasting method is more prone to structural controlled failure of the surrounding rock mass, while the TBM method would induce high stress concentration near the edge of excavation and more widely distributed of stress adjustment induced failure. As a result, the scale and frequency of the rockburst events generated by the TBM were significantly greater than those caused by the drilling-blasting method during the excavation of Jinping II diversion tunnels. The TBM method should be used carefully for tunnel excavation in high in-situ stress areas with burial depths of greater than 2000 m. If it is necessary to use the TBM method after a comprehensive selection, it is suggested that equipment adaptability improvement, advanced prediction, and prediction technology be used.

Sign in / Sign up

Export Citation Format

Share Document