scholarly journals Rock Mass Behavior under Tunnel Widening in Asymmetric and Symmetric Modes Considering Different Shapes and Parametric Conditions

Geosciences ◽  
2019 ◽  
Vol 9 (12) ◽  
pp. 518
Author(s):  
Babar Khan ◽  
Syed Muhammad Jamil ◽  
Jung Joo Kim ◽  
Turab H. Jafri ◽  
Jonguk Kim
Keyword(s):  
Rock Mass ◽  
In Situ Stress ◽  
Design Parameters ◽  
Tunnel Widening ◽  
Tunnel Support ◽  
Mass Behavior ◽  
Rock Types ◽  
The Difference ◽  
Support Conditions

To accommodate traffic volume on roads due to ever-increasing population growth, the widening of highways and motorways is in high demand. Nevertheless, the widening of tunnels on these road networks is quite complex due to the presence of numerous rock types, in situ stress, and different widening modes. To overcome these complexities, eight different tunnel shapes were simulated under varying support conditions for asymmetric and symmetric widening. It was found that the tunnels with a round shape, such as horseshoe and semicircular with flatbed, are more effective for asymmetric widening, whereas the provision of a rounded invert in these shapes can reverse the widening option to symmetric. Furthermore, an insignificant effect of the difference in asymmetric and symmetric widening of regular tunnel shapes, such as box, rectangular, and semi-elliptical, was found. A full factorial design statistical analysis confirmed the decrease in tunnel deformation by using various tunnel support systems and showed a significant deformation difference according to monitoring locations at the tunnel periphery. The deformation difference in the case of both tunnel widening modes was also analyzed according to different design parameters. This study provides a comprehensive understanding of rock mass behavior when the widening of any underground opening is carried out.

Analysis of TBM Tunnel Behavior in Jointed Rock Mass

2011 ◽  
Vol 90-93 ◽  
pp. 2033-2036 ◽  
Author(s):  
Jin Shan Sun ◽  
Hong Jun Guo ◽  
Wen Bo Lu ◽  
Qing Hui Jiang
Keyword(s):  
Rock Mass ◽  
Numerical Models ◽  
Jointed Rock ◽  
In Situ Stress ◽  
Jointed Rock Mass ◽  
Joint Orientation ◽  
Joint Spacing ◽  
Factors Affecting ◽  
Dip Angle

The factors affecting the TBM tunnel behavior in jointed rock mass is investigated. In the numerical models the concrete segment lining of TBM tunnel is concerned, which is simulated as a tube neglecting the segment joint. And the TBM tunnel construction process is simulate considering the excavation and installing of the segment linings. Some cases are analyzed with different joint orientation, joint spacing, joint strength and tunnel depth. The results show that the shape and areas of loosing zones of the tunnel are influenced by the parameters of joint sets and in-situ stress significantly, such as dip angle, spacing, strength, and the in-situ stress statement. And the stress and deformation of the tunnel lining are influenced by the parameters of joint sets and in-situ stress, too.

Study on Deformation and Damage of Rock Mass Subject to High In Situ Stress by Using a Elastoplastic Damage Model and Considering the Impact of Weak Planes

2013 ◽  
Vol 838-841 ◽  
pp. 705-709
Author(s):  
Yun Hao Yang ◽  
Ren Kun Wang
Keyword(s):  
Rock Mass ◽  
Large Scale ◽  
Damage Model ◽  
Back Analysis ◽  
In Situ Stress ◽  
Surrounding Rock ◽  
High In Situ Stress ◽  
Underground Caverns ◽  
The Impact

Large scale underground caverns are under construction in high in-situ stress field at Houziyan hydropower station. To investigate deformation and damage of surrounding rock mass, a elastoplastic orthotropic damage model capable of describing induced orthotropic damage and post-peak behavior of hard rock is used, together with a effective approach accounting for the presence of weak planes. Then a displacement based back analysis was conducted by using the measured deformation data from extensometers. The computed displacements are in good agreement with the measured ones at most of measurement points, which confirm the validities of constitutive model and numerical simulation model. The result of simulation shows that damage of surrounding rock mass is mainly dominated by the high in-situ stress rather than the weak planes and heavy damage occur at the cavern shoulders and side walls.

The Application of Hydraulic Fracturing in Storage Projects of Liquefied Petroleum Gas

2006 ◽  
Vol 306-308 ◽  
pp. 1509-1514 ◽  
Author(s):  
Jing Feng ◽  
Qian Sheng ◽  
Chao Wen Luo ◽  
Jing Zeng
Keyword(s):  
Rock Mass ◽  
Hydraulic Fracturing ◽  
Stress Measurement ◽  
Test Procedure ◽  
In Situ Stress ◽  
Test System ◽  
Petroleum Engineering ◽  
Liquefied Petroleum Gas

It is very important to study the pristine stress field in Civil, Mining, Petroleum engineering as well as in Geology, Geophysics, and Seismology. There are various methods of determination of in-situ stress in rock mass. However, hydraulic fracturing techniques is the most convenient method to determine and interpret the test results. Based on an hydraulic fracturing stress measurement campaign at an underground liquefied petroleum gas storage project which locates in ZhuHai, China, this paper briefly describes the various uses of stress measurement, details of hydraulic fracturing test system, test procedure adopted and the concept of hydraulic fracturing in arriving at the in-situ stresses of the rock mass.

Dynamic response of rock mass induced by the transient release of in-situ stress

2012 ◽  
Vol 53 ◽  
pp. 129-141 ◽  
Author(s):  
Wenbo Lu ◽  
Jianhua Yang ◽  
Peng Yan ◽  
Ming Chen ◽  
Chuangbing Zhou ◽  
...  
Keyword(s):  
Rock Mass ◽  
Dynamic Response ◽  
In Situ Stress

Microseism Induced by Transient Release of In Situ Stress During Deep Rock Mass Excavation by Blasting

2012 ◽  
Vol 46 (4) ◽  
pp. 859-875 ◽  
Author(s):  
Jianhua Yang ◽  
Wenbo Lu ◽  
Ming Chen ◽  
Peng Yan ◽  
Chuangbing Zhou
Keyword(s):  
Rock Mass ◽  
In Situ Stress ◽  
Deep Rock Mass ◽  
Deep Rock

scholarly journals Comparative Study of the Excavation Damage and Rockburst of the Deeply Buried Jinping II Diversion Tunnels Using a TBM and the Drilling-Blasting Method

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Jing Yang ◽  
Xing-Guo Yang ◽  
Jia-Wen Zhou ◽  
Yong Liu ◽  
Bao-Shun Dong ◽  
...  
Keyword(s):  
Rock Mass ◽  
Stress Concentration ◽  
High Stress ◽  
Tunnel Boring Machine ◽  
In Situ Stress ◽  
Surrounding Rock ◽  
High In Situ Stress ◽  
Damaged Zone ◽  
Blasting Method

The rock mass failure induced by high in-situ stresses during the excavation of deep diversion tunnels is one of the key problems in the construction of the Jinping II Hydropower Station. Based on the results of acoustic wave tests and rockburst statistical analysis conducted, this study focuses on the excavation damaged zone (EDZ) and rockburst events in the Jinping II diversion tunnels excavated using the tunnel boring machine (TBM) method and the drilling-blasting method. The unloading failure mechanism and the rockburst induced by the two different excavation methods were compared and analyzed. The results indicate that, due to the different stress adjustment processes, the degree of damage to the surrounding rock mass excavated using the drilling-blasting method was more serious than that using the TBM method. The EDZ induced by the TBM was usually distributed evenly along the edge of the excavation surface. While, the drilling-blasting method was more likely to cause stress concentration, resulting in a deeper EDZ in local areas. However, the TBM excavation method can cause other problems in high in-situ stress areas, such as strong rockbursts. The drilling-blasting method is more prone to structural controlled failure of the surrounding rock mass, while the TBM method would induce high stress concentration near the edge of excavation and more widely distributed of stress adjustment induced failure. As a result, the scale and frequency of the rockburst events generated by the TBM were significantly greater than those caused by the drilling-blasting method during the excavation of Jinping II diversion tunnels. The TBM method should be used carefully for tunnel excavation in high in-situ stress areas with burial depths of greater than 2000 m. If it is necessary to use the TBM method after a comprehensive selection, it is suggested that equipment adaptability improvement, advanced prediction, and prediction technology be used.

scholarly journals Effects Of Different Empirical Design Approaches For Size Galleries On The Behaviour Of Rock Masses During The Excavation Operation: Excavation Case At BAE Well

2021 ◽  
Vol 12 (5) ◽  
pp. 1167-1177
Author(s):  
Ismail Zaki, Et. al.
Keyword(s):  
Rock Mass ◽  
Support Systems ◽  
Resistance Index ◽  
In Situ Stress ◽  
Tunnel Excavation ◽  
High In Situ Stress ◽  
Rock Mass Quality ◽  
Empirical Approaches ◽  
Empirical Design

The characterization of rock massifs is a delicate job; indeed, it is possible to understand the behaviour of intact rocks individually by laboratory tests but it is difficult to characterize them on the whole rock mass, which has undergone a complex geological history. Empirical approaches play an important role in the excavation of galleries and the design of support systems. These approaches are considered very effective in optimizing the tunnel excavation process. Several reliable empirical approaches have been developed, but the selection or use of an appropriate empirical method to design the tunnel excavation remains a difficult task. Therefore, in this work, the analysis of four approaches, the most used, of different empirical design was carried out to determine the behaviour of the rock mass during its excavation in a state of high in situ stress. This study was carried out on the scale of the ST2 rock mass of the worksite (BAE well 3) at the Bouazzer mine. These approaches include the AFTES classification, rock mass index (RMR), rock mass quality (Q) and geological resistance index (GSI). Based on the simulated statistical results obtained from said empirical approaches, through the finite element calculation, it was found that the application of the rock mass quality approach is very efficient in the excavation of the rock mass. gallery of size because it makes it possible to take into account the equivalent dimensions of the gallery, the stress condition in situ due to the excavation and the heights of overburden which are considered as major elements of the stability of the gallery. The method provides an optimized reinforcement and support design. In addition, this study will serve as a valuable basic document for the geotechnical engineer to design and plan support systems in the excavation of galleries under high in-situ stress.

scholarly journals Numerical Investigation of the Impacts of Borehole Breakouts on Breakdown Pressure

Energies ◽  
2019 ◽  
Vol 12 (5) ◽  
pp. 888 ◽  
Author(s):  
Hua Zhang ◽  
Shunde Yin ◽  
Bernt Aadnoy
Keyword(s):  
Hydraulic Fracturing ◽  
Shear Failure ◽  
In Situ Stress ◽  
Test Results ◽  
Breakdown Pressure ◽  
Borehole Breakout ◽  
Borehole Breakouts ◽  
The Difference ◽  
Mud Pressure

Borehole breakouts appear in drilling and production operations when rock subjected to in situ stress experiences shear failure. However, if a borehole breakout occurs, the boundary of the borehole is no longer circular and the stress distribution around it is different. So, the interpretation of the hydraulic fracturing test results based on the Kirsch solution may not be valid. Therefore, it is important to investigate the factors that may affect the correct interpretation of the breakdown pressure in a hydraulic fracturing test for a borehole that had breakouts. In this paper, two steps are taken to implement this investigation. First, sets of finite element modeling provide sets of data on borehole breakout measures. Second, for a given measure of borehole breakouts, according to the linear relation between the mud pressure and the stress on the borehole wall, the breakdown pressure considering the borehole breakouts is acquired by applying different mud pressure in the model. Results show the difference between the breakdown pressure of a circular borehole and that of borehole that had breakouts could be as large as 82% in some situations.

Sign in / Sign up

Export Citation Format

Share Document