Piezoelectric properties of Li, Sb, and Ta co-doped (K,Na)NbO3 ceramics with fine grain size sintered by SPS method

2013 ◽  
Vol 30 (4) ◽  
pp. 217-220 ◽  
Author(s):  
Hui Zhang ◽  
Xiaohui Wang ◽  
Jian Fang ◽  
Yichi Zhang ◽  
Longtu Li
2008 ◽  
Vol 368-372 ◽  
pp. 8-10 ◽  
Author(s):  
Ting Ting Zou ◽  
Xiao Hui Wang ◽  
Long Tu Li

High-performance fine-grain (1-x)BiScO3-xPbTiO3 ceramics were prepared by two-step sintering method. Influences of sintering temperature, holding time, and composition on the microstructure and properties were discussed. The BSPT ceramics obtained via two-step sintering reaches density higher than 95% at a low temperature of 800°C without any sintering aid, and the grain size of the ceramics is also effectively controlled. Excellent piezoelectric properties between the composition of x=0.63 and x=0.64 reveals a probable MPB in this range, suggesting a potential approach to pursue high performance BSPT ceramics.


Author(s):  
R. Sinclair ◽  
B.E. Jacobson

INTRODUCTIONThe prospect of performing chemical analysis of thin specimens at any desired level of resolution is particularly appealing to the materials scientist. Commercial TEM-based systems are now available which virtually provide this capability. The purpose of this contribution is to illustrate its application to problems which would have been intractable until recently, pointing out some current limitations.X-RAY ANALYSISIn an attempt to fabricate superconducting materials with high critical currents and temperature, thin Nb3Sn films have been prepared by electron beam vapor deposition [1]. Fine-grain size material is desirable which may be achieved by codeposition with small amounts of Al2O3 . Figure 1 shows the STEM microstructure, with large (∽ 200 Å dia) voids present at the grain boundaries. Higher quality TEM micrographs (e.g. fig. 2) reveal the presence of small voids within the grains which are absent in pure Nb3Sn prepared under identical conditions. The X-ray spectrum from large (∽ lμ dia) or small (∽100 Ǻ dia) areas within the grains indicates only small amounts of A1 (fig.3).


Author(s):  
Yihong Xian ◽  
Weijun He ◽  
Wenhuan Chen ◽  
Zejun Chen ◽  
Bing Jiang ◽  
...  
Keyword(s):  

2021 ◽  
Vol 83 (4) ◽  
Author(s):  
S. Adam Soule ◽  
Michael Zoeller ◽  
Carolyn Parcheta

AbstractHawaiian and other ocean island lava flows that reach the coastline can deposit significant volumes of lava in submarine deltas. The catastrophic collapse of these deltas represents one of the most significant, but least predictable, volcanic hazards at ocean islands. The volume of lava deposited below sea level in delta-forming eruptions and the mechanisms of delta construction and destruction are rarely documented. Here, we report on bathymetric surveys and ROV observations following the Kīlauea 2018 eruption that, along with a comparison to the deltas formed at Pu‘u ‘Ō‘ō over the past decade, provide new insight into delta formation. Bathymetric differencing reveals that the 2018 deltas contain more than half of the total volume of lava erupted. In addition, we find that the 2018 deltas are comprised largely of coarse-grained volcanic breccias and intact lava flows, which contrast with those at Pu‘u ‘Ō‘ō that contain a large fraction of fine-grained hyaloclastite. We attribute this difference to less efficient fragmentation of the 2018 ‘a‘ā flows leading to fragmentation by collapse rather than hydrovolcanic explosion. We suggest a mechanistic model where the characteristic grain size influences the form and stability of the delta with fine grain size deltas (Pu‘u ‘Ō‘ō) experiencing larger landslides with greater run-out supported by increased pore pressure and with coarse grain size deltas (Kīlauea 2018) experiencing smaller landslides that quickly stop as the pore pressure rapidly dissipates. This difference, if validated for other lava deltas, would provide a means to assess potential delta stability in future eruptions.


2020 ◽  
Vol 39 (1) ◽  
pp. 595-598
Author(s):  
Cui Chaopeng ◽  
Zhu Xiangwei ◽  
Li Qiang ◽  
Zhang Min ◽  
Zhu Guangping

AbstractThe Mo/ZrO2 electrode was prepared by combining hydrothermal synthesis with powder metallurgy, and this new electrode material has a totally different microstructure from the conventional electrode. The grain size of the new electrode was fine, and the size of ZrO2 in the alloy reached 200 nm. According to the results, the Mo–ZrO2 electrode has better performance, because the erosion occurs along the grain boundaries. Meanwhile, the new electrode, based on its fine grain, can effectively improve the corrosion resistance of the electrode.


2013 ◽  
Vol 347-350 ◽  
pp. 1171-1175 ◽  
Author(s):  
Bin Wang ◽  
Hong Mei Hu ◽  
Cui Zhou

The transverse properties were inferior to the longitudinal properties for the existence of banded structure in 20G steel. In order to eliminate the banded structure and improve the transverse performance of 20G steel, different heat treatment processes were adopted. The results showed that conventional normalizing could reduce the banded structure and refine the grain sizes. When 20G was heated with 10°C/min heating rated and then held at 920°C for 2h, the banded structure in the steel was almost eliminated and the microstructure was homogeneous with fine grain size, the strength increased by 14%. The non-metallic inclusion and carbide in the microstructure leaded to stress concentration and separation with the base metal. To some extent, heat treatment can improve the distribution and form of non-metallic inclusions.


2008 ◽  
Vol 22 (18n19) ◽  
pp. 2833-2939 ◽  
Author(s):  
S. M. FATEMI-VARZANEH ◽  
A. ZAREI-HANZAKI ◽  
M. HAGHSHENAS

This work conducted to investigate the effects of accumulative roll bonding (ARB) method on achieving the ultra-fine grain microstructure in AZ31 alloy. Accordingly, a number of ARB routes at 400°C, applying thickness reductions per pass of 35%, 55%, and 85% were performed. The results indicate that both the final grain size and the degree of bonding have been dictated by the thickness reduction per pass. The larger pass reductions promote a higher degree of bonding. Increasing the total strain stimulates the formation of a more homogeneous ultra fine grain microstructure.


Sign in / Sign up

Export Citation Format

Share Document