Experimental Evidence on the Enhancement of Bearing Load Capacity by Localised Boundary Slip Effect

2021 ◽  
Vol 69 (2) ◽  
Author(s):  
B. W. Sun ◽  
L. Chen ◽  
L. Guo ◽  
W. Wang ◽  
P. L. Wong
Keyword(s):  
Experimental Evidence ◽  
Load Capacity ◽  
Slip Effect ◽  
Boundary Slip ◽  
Bearing Load

scholarly journals Improvement of Tilting-Pad Journal Bearing Operating Characteristics by Application of Eddy Grooves

Lubricants ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 18
Author(s):  
Eckhard Schüler ◽  
Olaf Berner
Keyword(s):  
High Speed ◽  
Journal Bearing ◽  
Load Capacity ◽  
Fluid Film ◽  
Operating Characteristics ◽  
Fluid Film Bearings ◽  
Tilting Pad ◽  
Bearing Load ◽  
Bearing Loads ◽  
Tilting Pad Journal Bearing

In high speed, high load fluid-film bearings, the laminar-turbulent flow transition can lead to a considerable reduction of the maximum bearing temperatures, due to a homogenization of the fluid-film temperature in radial direction. Since this phenomenon only occurs significantly in large bearings or at very high sliding speeds, means to achieve the effect at lower speeds have been investigated in the past. This paper shows an experimental investigation of this effect and how it can be used for smaller bearings by optimized eddy grooves, machined into the bearing surface. The investigations were carried out on a Miba journal bearing test rig with Ø120 mm shaft diameter at speeds between 50 m/s–110 m/s and at specific bearing loads up to 4.0 MPa. To investigate the potential of this technology, additional temperature probes were installed at the crucial position directly in the sliding surface of an up-to-date tilting pad journal bearing. The results show that the achieved surface temperature reduction with the optimized eddy grooves is significant and represents a considerable enhancement of bearing load capacity. This increase in performance opens new options for the design of bearings and related turbomachinery applications.

A General Solution of Reynolds’ Equation for a Full Finite Journal Bearing

1967 ◽  
Vol 89 (2) ◽  
pp. 203-210 ◽  
Author(s):  
R. R. Donaldson
Keyword(s):  
Fourier Series ◽  
Series Solution ◽  
Reynolds Equation ◽  
Journal Bearing ◽  
Load Capacity ◽  
Separation Of Variables ◽  
Hill Equation ◽  
Eigenvalues And Eigenvectors ◽  
General Series ◽  
Bearing Load

Reynolds’ equation for a full finite journal bearing lubricated by an incompressible fluid is solved by separation of variables to yield a general series solution. A resulting Hill equation is solved by Fourier series methods, and accurate eigenvalues and eigenvectors are calculated with a digital computer. The finite Sommerfeld problem is solved as an example, and precise values for the bearing load capacity are presented. Comparisons are made with the methods and numerical results of other authors.

Numerical and experimental studies on the thermal and static characteristics of multi-leaf foil thrust bearing

2021 ◽  
pp. 135065012110110
Author(s):  
Yu Guo ◽  
Yu Hou ◽  
Qi Zhao ◽  
Xionghao Ren ◽  
Shuangtao Chen ◽  
...  
Keyword(s):  
High Speed ◽  
Thrust Bearing ◽  
Load Capacity ◽  
Failure Process ◽  
Experimental Studies ◽  
Elastic Model ◽  
Static Characteristics ◽  
Bearing Load ◽  
Foil Thrust Bearing ◽  
Cooling Air

Foil bearing is considered to be a promising supporting technology in high-speed centrifugal machinery. Due to the high-speed shearing effect in the viscous lubricant film, heat generation could not be ignored. In this paper, a thermo-elastic model of the multi-leaf foil thrust bearing is proposed to predict its thermal and static characteristics. In the model, modified Reynolds equation, energy equation, and Kirchhoff equation are solved in a coupling way. The contact area between the foil and welding plate is taken into account. Besides, the effect of cooling air on the bearing temperature is investigated. The ultimate load capacity and transient overload failure process of the bearing is analyzed and discussed. The effect of rotation speed on the bearing temperature is more obvious than that of the bearing load. The bearing temperature drops obviously by introducing the cooling air, and the cooling effect is improved with the supply pressure. The transient overload failure of the bearing occurs when the bearing load exceeds the ultimate value.

Investigation of slip/no-slip surface for two-dimensional large tilting pad thrust bearing

2017 ◽  
Vol 69 (6) ◽  
pp. 995-1004 ◽  
Author(s):  
Zhixiang Song ◽  
Fei Guo ◽  
Ying Liu ◽  
Songtao Hu ◽  
Xiangfeng Liu ◽  
...  
Keyword(s):  
Reynolds Number ◽  
Slip Surface ◽  
Load Capacity ◽  
Slip Condition ◽  
Optimized Design ◽  
Two Dimensional ◽  
Boundary Slip ◽  
Content Type ◽  
Tilting Pad ◽  
Turbulence Effect

Purpose This paper aims to present the slip/no-slip design in two-dimensional water-lubricated tilting pad thrust bearings (TPTBs) considering the turbulence effect and shifting of pressure centers. Design/methodology/approach A numerical model is established to analyze the slip condition and the effect of turbulence according to a Reynolds number defined in terms of the slip condition. Simulations are carried out for eccentrically and centrally pivoted bearings and the influence of different slip parameters is discussed. Findings A considerable enhancement in load capacity, as well as a reduction in friction, can be achieved by heterogeneous slip/no-slip surface designs for lubricated sliding contacts, especially for near parallel pad configurations. The optimized design largely depends on the pivot position. The load capacity increases by 174 per cent for eccentrically pivoted bearings and 159 per cent for centrally pivoted bearings for a suitable design. When slip zone locates at the middle of the radial direction or close to the inner edge, the performance of the TPTB is better. Research limitations/implications The simplification of slip effect on the turbulence (definition of Reynolds number) can only describe the trend of the increasing turbulence due to slip condition. The accurate turbulence expression considering the boundary slip needs further explorations. Originality/value The shifting of pressure center due to the slip/no-slip design for TPTBs is investigated in this study. The turbulence effect and influence of slip parameters is discussed for large water-lubricated bearings.

An Approximate THD Theory for Journal Bearings

1990 ◽  
Vol 112 (2) ◽  
pp. 224-229 ◽  
Author(s):  
G. Gupta ◽  
C. R. Hammond ◽  
A. Z. Szeri
Keyword(s):  
Journal Bearing ◽  
Load Capacity ◽  
Pressure Coefficient ◽  
Journal Bearings ◽  
Maximum Pressure ◽  
Substantial Agreement ◽  
Interactive Mode ◽  
Lubricant Flow ◽  
Bearing Load ◽  
Sophisticated Model

The aim of this paper is to make available to the industrial designer results of the thermohydrodynamic theory of journal bearings, by providing a simplified, yet accurate model of journal bearing lubrication that can be implemented on a personal computer and be used in an interactive mode. The simplified THD theory we propose consists of two coupled ordinary differential equations for pressure and energy and an algebraic equation for viscosity, which are to be solved iteratively. Bearing load capacity, maximum bearing temperature, maximum pressure, coefficient of friction and lubricant flow rate calculated from this simplified theory compare well with results from a more sophisticated model. We also make comparisons with experimental data on full journal bearings, demonstrating substantial agreement between experiment and simplified theory.

Influence of Nanoparticles in Lubricants on the Load Capacity of Hydrostatic Thrust Bearings

2012 ◽  
Vol 486 ◽  
pp. 99-103
Author(s):  
Huei Chu Weng ◽  
Yuan Kang
Keyword(s):  
Volume Fraction ◽  
Load Capacity ◽  
Particle Volume Fraction ◽  
Closed Form Solution ◽  
Form Solution ◽  
Interparticle Interaction ◽  
Particle Volume ◽  
Thrust Bearings ◽  
Bearing Load ◽  
Thrust Pad

An analysis for the effect of nanoparticles in lubricants on load capacity is performed to study a rectangular thrust pad hydrostatic bearing with a central recess. The closed-form solution of the bearing load is derived analytically and presented for nanofluids with interparticle interaction. Results reveal that in the presence of nanoparticles, the enhanced viscosity could result in an increase in bearing load; moreover, this increase dramatically increases as particle volume fraction and/or interparticle interaction increases. The effect of nanoparticles on the bearing load can be magnified by decreasing the bearing gap.

Theoretical Study on Static Performance of Herringbone Grooved Aerodynamics Foil Bearing

2020 ◽  
Author(s):  
ZeDa Dong ◽  
Cheng Cheng ◽  
Fangcheng Xu
Keyword(s):  
Power Consumption ◽  
Reynolds Equation ◽  
Load Capacity ◽  
Structural Parameters ◽  
Operational Parameters ◽  
Film Pressure ◽  
Friction Power ◽  
Foil Bearings ◽  
Bearing Load ◽  
Herringbone Grooves

Abstract In this paper, the mathematical model of herringbone grooved aerodynamic foil bearings is established, and the finite difference method is used to obtain the discretized form of Reynolds equation. The static characteristics of bearings, such as film pressure, film temperature, are obtained by solving the Reynolds equation and energy equation. The bearing load capacity and friction power consumption are obtained by calculating the film thickness and film pressure distribution in the bearing gap. The influence of the bearing operational parameters, such as eccentricity and rotation speed, and the bearing structural parameters, such as groove width, groove depth ratio, groove number and helix angle, on the bearing load capacity and friction power consumption of bearings are analyzed. The methods of improving bearing load capacity and reducing friction power consumption are obtained. Simultaneously, by comparing the bearing load capacity and friction power consumption of herringbone grooved gas foil bearings and gas foil bearings (GFBs) without herringbone grooves, the influence of herringbone grooves on the bearing performance is obtained.

Sign in / Sign up

Export Citation Format

Share Document