Reduction of Water Vapor Permeability in Food Multilayer Biopackaging by Epitaxial Crystallization of Beeswax

2021 ◽  
Author(s):  
Florencia Cruces ◽  
María Guadalupe García ◽  
Nelio Ariel Ochoa
Keyword(s):  
Water Vapor ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Epitaxial Crystallization

Ultraviolet blocking and antioxidant polyvinyl alcohol films incorporated with baicalin extraction from Scutellaria baicalensis Georgi

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Jinshu Liu ◽  
Xiaoyan Ma ◽  
Wenzhao Shi ◽  
Jianwei Xing ◽  
Chaoqun Ma ◽  
...  
Keyword(s):  
Water Vapor ◽  
Polyvinyl Alcohol ◽  
Radical Scavenging Activity ◽  
Antioxidant Properties ◽  
Radical Scavenging ◽  
Water Vapor Permeability ◽  
Scutellaria Baicalensis ◽  
Vapor Permeability ◽  
Protective Film ◽  
Uv Blocking

Abstract Baicalin, an active flavonoid ingredient of Scutellaria baicalensis Georgi, was extracted by heat reflux extraction and showed the same significance UV absorption property with standard baicalin. Active films were prepared from polyvinyl alcohol (PVA) containing baicalin extract by casting method. The effect of baicalin extracts on the UV-blocking, optical, antioxidant property, water vapor permeability, swelling and mechanical properties of the films were studied. UV–vis transmittance spectra showed that PVA films incorporated with baicalin extract blocked ultraviolet light range from 280–400 nm even with low concentration of baicalin (0.5 wt%) and maintain the high transparency in visible spectrum. The outstanding UV-blocking properties of PVA films incorporated with baicalin extract were also confirmed by Rhodamine B degradation. Baicalin conferred antioxidant properties to PVA films as determined by DPPH radical scavenging activity. Due to the interaction between hydroxy groups of baicalin and PVA molecule, water vapor permeability, swelling and elongation at break of the films were decreased accompanied with the increasing in tensile strength and Young’s modulus. FTIR reveal that the interaction between PVA molecules was significant changed by the introduction of baicalin. These results suggest that PVA film incorporated with baicalin extract can be used for the development of functional protective film.

scholarly journals The Effect of Extraction Conditions on the Barrier and Mechanical Properties of Kefiran Films

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 602
Author(s):  
Carmen Rodica Pop ◽  
Teodora Emilia Coldea ◽  
Liana Claudia Salanţă ◽  
Alina Lăcrămioara Nistor ◽  
Andrei Borşa ◽  
...  
Keyword(s):  
Water Vapor ◽  
Conformational Changes ◽  
Water Vapor Permeability ◽  
Edible Films ◽  
Film Structure ◽  
Water Soluble ◽  
Vapor Permeability ◽  
Water Molecules ◽  
Compact Structure ◽  
Technology Applications

Kefiran is an exopolysaccharide classified as a heteropolysaccharide comprising glucose and galactose in equimolar quantities, and it is classified as a water-soluble glucogalactan. This work aimed to investigate the effect of different extraction conditions of kefiran on the structural and physical properties of the edible films obtained. Fourier-transform infrared spectroscopy and scanning electron microscopy were performed, together with a determinations of moisture content, solubility, water vapor permeability and degree of swelling. The kefiran films presented values of the water vapor permeability between 0.93 and 4.38 × 10−11 g/m.s.Pa. These results can be attributed to the development of a more compact structure, where glycerol had no power to increase the free volume and the water vapor diffusion through their structure. The possible conformational changes in the kefiran film structure, due to the interspersing of the plasticizers and water molecules that they absorb, could be the reason for producing flexible kefiran films in the case of using glycerol as a plasticizer at 7.5% w/w. Moreover, it was observed that the extraction conditions are a significant factor in the properties of these films and their food technology applications.

scholarly journals Development of PE/PCL Bilayer Films Modified with Casein and Aluminum Oxide

Molecules ◽  
2021 ◽  
Vol 26 (11) ◽  
pp. 3090
Author(s):  
Anita Ptiček Siročić ◽  
Ana Rešček ◽  
Zvonimir Katančić ◽  
Zlata Hrnjak-Murgić
Keyword(s):  
Mechanical Properties ◽  
Thermal Properties ◽  
Water Vapor ◽  
Aluminum Oxide ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Mechanical And Thermal Properties ◽  
Oxide Compound ◽  
Bilayer Films ◽  
Oxide Particles

The studied samples were prepared from polyethylene (PE) polymer which was coated with modified polycaprolactone (PCL) film in order to obtain bilayer films. Thin PCL film was modified with casein/aluminum oxide compound to enhance vapor permeability as well as mechanical and thermal properties of PE/PCL films. Casein/aluminum oxide modifiers were used in order to achieve some functional properties of polymer film that can be used in various applications, e.g., reduction of water vapor permeability (WVTR) and good mechanical and thermal properties. Significant improvement was observed in mechanical properties, especially in tensile strength as well as in water vapor values. Samples prepared with aluminum oxide particles indicated significantly lower values up to 60%, and samples that were prepared with casein and 5% Al2O3 showed the lowest WVTR value.

scholarly journals Upcycling of Vine Shoots: Production of Fillers for PHBV-Based Biocomposite Applications

2020 ◽  
Author(s):  
Grégoire David ◽  
Laurent Heux ◽  
Stéphanie Pradeau ◽  
Nathalie Gontard ◽  
Hélène Angellier-Coussy
Keyword(s):  
Water Vapor ◽  
Gas Phase ◽  
Mechanical Performance ◽  
Low Cost ◽  
Water Vapor Permeability ◽  
Contact Angles ◽  
Vapor Permeability ◽  
Water Contact ◽  
Median Diameter ◽  
Cost Of Materials

Abstract This paper aims at investigating the potential of vine shoots (ViSh) upcycling as fillers in novel poly(3-hydroxybutyrate-3-hydroxyvalerate) (PHBV) based biocomposites. ViSh particles of around 50 µm (apparent median diameter) were obtained combining dry grinding processes, and mixed with PHBV using melt extrusion. Thermal stability and elongation at break of biocomposites were reduced with increasing contents of ViSh particles (10, 20 and 30 wt%), while Young’s modulus and water vapor permeability were increased. It was shown that a surface gas-phase esterification allowed to significantly increase the hydrophobicity of ViSh particles (increase of water contact angles from 59° to 114°), leading to a reduction of 27% in the water vapor permeability of the biocomposite filled with 30 wt% of ViSh. The overall mechanical performance was not impacted by gas-phase esterification, demonstrating that the interfacial adhesion between the virgin ViSh particles and the PHBV matrix was already good and that such filler surface treatment was not required in that case. It was concluded that ViSh particles can be interestingly used as low cost fillers in PHBV-based biocomposites to decrease the overall cost of materials.

Water-vapor permeability control of PDMS by the dispersion of collagen powder

2009 ◽  
Vol 4 (3) ◽  
pp. 442-449 ◽  
Author(s):  
Yuhua Zhang ◽  
Masatoshi Ishida ◽  
Yutaka Kazoe ◽  
Yohei Sato ◽  
Norihisa Miki
Keyword(s):  
Water Vapor ◽  
Water Vapor Permeability ◽  
Vapor Permeability ◽  
Collagen Powder

scholarly journals Incorporation of bentonite clay in cassava starch films for the reduction of water vapor permeability

2018 ◽  
Vol 105 ◽  
pp. 637-644 ◽  
Author(s):  
M.K.S. Monteiro ◽  
V.R.L. Oliveira ◽  
F.K.G. Santos ◽  
E.L. Barros Neto ◽  
R.H.L. Leite ◽  
...  
Keyword(s):  
Water Vapor ◽  
Water Vapor Permeability ◽  
Bentonite Clay ◽  
Cassava Starch ◽  
Vapor Permeability ◽  
Starch Films

Polyurethane Electrospun Fiber Biomimetics Membrane for Constructing the Structure of Grain Layer with Good Breathability for Cattle Split Leather

2021 ◽  
Vol 116 (8) ◽  
Author(s):  
Nan Chen ◽  
Yanchun Li ◽  
Jianbo Qu ◽  
Jian-Yong Wang
Keyword(s):  
Water Vapor ◽  
Electrospun Fiber ◽  
Water Vapor Permeability ◽  
Waterborne Polyurethane ◽  
Vapor Permeability ◽  
High Porosity ◽  
Foam Layer ◽  
Fiber Morphology ◽  
Woven Structure ◽  
Superfine Fiber

The traditional thick coating on split leather does not have the ability to breathe like full grain leather.  The air and water vapor permeabilities of full grain leather are well known properties due to its fiber woven structure. Simulating the fiber morphology and weaving structure of the dermis or grain layer is very important to construct a top surface layer for split leather. In this paper, a PU (polyurethane) foam layer is put first on the split to enhance the adhesion of a second application of a superfine fibrous PU resin. This foam uses well-known waterborne polyurethane foaming technology. This dried foam has good breathability because of high porosity. A superfine fiber membrane is next put atop of the foam layer by using an electro-spun polyurethane resin. This second resin imitates collagen fibers in the network structure of the leathers’ grain layer. Thus, this resultant electrospun fiber biomimetics membrane simulated the grain layer of natural leather. SEM showed the morphology and structure of this electrospun fiber biomimetic membrane to be like that of the grain layer of natural leather. The porosity and apparent density were basically the same as the grain of leather, which were 63.65% and 583.878 kg/m3 respectively. The air and water vapor permeability of the biomimetics membrane were also as high as 2250 mL·cm-2·h-1 and 8753.02 μg·cm-2·h-1 respectively. Therefore, the biomimetics membrane largely restored the ability to breathe of split leather. Thus, this method simulates the performance and structure of full grain leather and is a novel method for industrial production

scholarly journals Drying parameters of rendering mortars

2018 ◽  
Vol 18 (2) ◽  
pp. 7-19 ◽  
Author(s):  
Maria Cláudia de Freitas Salomão ◽  
Elton Bauer ◽  
Claudio de Souza Kazmierczak
Keyword(s):  
Water Vapor ◽  
Water Transport ◽  
Liquid Water ◽  
Water Vapor Permeability ◽  
Water Vapor Transport ◽  
Experimental Program ◽  
Vapor Permeability ◽  
Capillary Absorption ◽  
Drying Behavior ◽  
Drying Curves

Abstract The objective of this article was to study the drying behavior of rendering mortars. Cement-lime mortars with different mix proportions were evaluatedto analyze the influence of mix materials on water transport. The experimental program was produced to observe the transport of liquid water and vapor water in mortars during the drying process. The liquid water transport was studied through capillary absorption and the water vapor transport by the water vapor permeability test. The drying curves used to investigate drying kinetics were obtained according to the methodology recommended by European standard EN 16322. In summary, it is possible to affirm that the aggregate, the binder and water contents determine the behavior of the mortars regarding water transport. The drying index is considered a good indicator of the easiness of both liquid and vapor water transport.

scholarly journals Characteristics of Knitted Structures Produced by Engineered Polyester Yarns and Their Blends in Terms of Thermal Comfort

2015 ◽  
Vol 10 (1) ◽  
pp. 155892501501000 ◽  
Author(s):  
Nida Oğlakcioğlu ◽  
Ahmet Çay ◽  
Arzu Marmarali ◽  
Emel Mert
Keyword(s):  
Water Vapor ◽  
Thermal Comfort ◽  
Moisture Transfer ◽  
Water Vapor Permeability ◽  
Air Permeability ◽  
Vapor Permeability ◽  
Moisture Management ◽  
Thermal Comfort Properties ◽  
Knitted Structure ◽  
Drying Properties

Engineered yarns are used to provide better clothing comfort for summer garments because of their high levels of moisture and water vapor management. The aim of this study was to investigate the characteristics of knitted structures that were produced using different types of polyester yarns in order to achieve better thermal comfort properties for summer clothing. However they are relatively expensive. Therefore, in this study engineered polyester yarns were combined with cotton and lyocell yarns by plying. This way, the pronounced characteristics of these yarns were added to the knitted structure as well. Channeled polyester, hollow polyester, channeled/hollow blended polyester, cotton, and lyocell yarns were plied with each other and themselves. Then, single jersey structures were knitted using these ply yarn combinations and air permeability, thermal resistance, thermal absorptivity, water vapor permeability, moisture management, and drying properties were tested. The results indicate that channeled PES fabrics are advantageous for hot climates and high physical activities with regards to high permeability and moisture transfer and also to fast drying properties. Besides, air permeability and thermal properties improved through the combination of lyocell yarn with engineered polyester yarns. However, the use of lyocell or cotton with engineered yarns resulted in a to a decrease in moisture management properties and an increase in drying times

Sign in / Sign up

Export Citation Format

Share Document