scholarly journals Synthesis and properties of a novel alkyl-hydroxyl-sulfobetaine zwitterionic surfactant for enhanced oil recovery

2014 ◽  
Vol 5 (3) ◽  
pp. 321-326 ◽  
Author(s):  
Shufeng Guo ◽  
Hongyan Wang ◽  
Jing Shi ◽  
Binlin Pan ◽  
Yuqiao Cheng
2019 ◽  
Vol 2 (2) ◽  
pp. 27-28
Author(s):  
Yosamin Esanullah ◽  
Japan Trivedi ◽  
Benedicta Nwani ◽  
Madison Barth

The increase in energy demand has led to extensive research and development on economically, environmentally and technically feasible ways of improving the ever-growing energy demand. A common derivative of energy is from hydrocarbons, specifically oil. The process of oil recovery can be divided into primary, secondary, and tertiary recovery (also known as enhanced oil recovery). Once the internal pressure of a reservoir has depleted enough during primary and secondary recovery, more advanced techniques in enhanced oil recovery mechanisms are used to recover 50-80% of oil in the reservoir. Tertiary recovery includes the use of surfactants to reduce interfacial tension (IFT) or alter wettability. In this work, a zwitter ionic surfactant at two different concentrations is evaluated for its ability to reduce the interfacial tension between oil and water, as well as altering wettability in silurian dolomite. To achieve this, fluid-fluid analysis was done by a compatibility test, phase behavior test and interfacial tension measurements. Rock-fluid analysis was also completed by means of floatation test, carried out with carbonate rock particles to analyze the surfactant’s ability to alter wettability. Solution pH measurements were taken to validate the qualitative floatation test results. Results show that the surfactant, chembetaine C surfactant, is compatible with all ranges of salinities investigated, though was not able to produce a winsor type III micro-emulsion. The results of the interfacial tension measurements are in line with the phase behavior test, as none of the measurements were at ultra-low values. Surfactant retention is likely to occur with the analyzed zwitterionic surfactant based on the fluid-fluid analysis. Qualitative results from the floatation test show that the wettability of the carbonate rock particles cannot be significantly altered to more water-wet conditions. The pH of the solution remains at alkaline values, which can be beneficial in enhanced oil recovery in producing soap in situ, also known as saponification. Overall, tests conclude that this zwitterionic surfactant at 1% concentration would be most effective at 10,000 ppm salinity brine, though overall is not suitable for chemically enhanced oil recovery.


Energies ◽  
2019 ◽  
Vol 12 (6) ◽  
pp. 1163 ◽  
Author(s):  
Muhammad Kamal

Selection of surfactants for enhanced oil recovery and other upstream applications is a challenging task. For enhanced oil recovery applications, a surfactant should be thermally stable, compatible with reservoir brine, and have lower adsorption on reservoir rock, have high foamability and foam stability, and should be economically viable. Foam improves the oil recovery by increasing the viscosity of the displacing fluid and by reducing the capillary forces due to a reduction in interfacial tension. In this work, foamability and foam stability of two different surfactants were evaluated using a dynamic foam analyzer. These surfactants were fluorinated zwitterionic, and hydrocarbon zwitterionic surfactants. The effect of various parameters such as surfactant type and structure, temperature, salinity, and type of injected gas was investigated on foamability and foam stability. The foamability was assessed using the volume of foam produced by injecting a constant volume of gas and foam stability was determined by half-life time. The maximum foam generation was obtained using hydrocarbon zwitterionic surfactant. However, the foam generated using fluorinated zwitterionic surfactant was more stable. A mixture of zwitterionic fluorinated and hydrocarbon fluorinated surfactant showed better foam generation and foam stability. The foam generated using CO2 has less stability compared to the foam generated using air injection. Presence of salts increases the foam stability and foam generation. At high temperature, the foamability of the surfactants increased. However, the foam stability was reduced at high temperature for all type of surfactants. This study helps in optimizing the surfactant formulations consisting of a fluorinated and hydrocarbon zwitterionic surfactant for foam injections.


Sign in / Sign up

Export Citation Format

Share Document