Optimization of Nail Inclination Angle in Soil Nail Walls Based on a Prevalent Limit Equilibrium Method

2021 ◽  
Author(s):  
Mohammad Reza Arvin ◽  
Ehsan Ghavami ◽  
Mehran Motamedi Azari
Keyword(s):  
Inclination Angle ◽  
Limit Equilibrium ◽  
Limit Equilibrium Method ◽  
Soil Nail ◽  
Equilibrium Method

Research on 2D Limit Equilibrium Method of Slopes Considering the Effect of Horizontal In Situ Stress

2013 ◽  
Vol 671-674 ◽  
pp. 245-250
Author(s):  
Wen Hui Tan ◽  
Ya Liang Li ◽  
Cong Cong Li
Keyword(s):  
Limit Equilibrium ◽  
Limit Equilibrium Method ◽  
In Situ Stress ◽  
Open Pit ◽  
Open Pit Mines ◽  
Equilibrium Method ◽  
Iron Mine ◽  
The Stability ◽  
Slice Method

At present, in-situ stress was not considered in Limit Equilibrium Method (LEM) of slopes, the influence of in-situ stress is very small on the stability of conventional slopes, but in deep-depressed open-pit mines, the influence should not be neglected. Formula for calculating the Factor of Safety (FOS) under the effect of horizontal in-situ stress was deduced using General Slice Method (GSM) of two-dimensional (2D) limit equilibrium method in this paper，a corresponding program SSLOPE was built, and the software was used in a deep- depressed open-pit iron mine. The results show that the FOS of the slope decreased by 20% when horizontal in-situ stress is considered, some reinforcements must be taken. Therefore, the influence of in-situ stress on slope stability should be taken into account in deep open –pit mines.

Slope Stability Analysis of Elastic Limit Equilibrium Method

2013 ◽  
Vol 275-277 ◽  
pp. 1423-1426
Author(s):  
Lin Kuang ◽  
Ai Zhong Lv ◽  
Yu Zhou
Keyword(s):  
Stability Analysis ◽  
Slope Stability ◽  
Safety Factor ◽  
Slip Surface ◽  
Limit Equilibrium ◽  
Limit Equilibrium Method ◽  
Slope Stability Analysis ◽  
Sliding Surface ◽  
Tangential Stresses ◽  
Equilibrium Method

Based on finite element analysis software ANSYS, slope stability analysis is carried out by Elastic limiting equilibrium method proposed in this paper. A series of sliding surface of the slope can be assumed firstly, and then stress field along the sliding surface is analyzed as the slope is in elastic state. The normal and tangential stresses along each sliding surface can be obtained, respectively. Then the safety factor for each slip surface can be calculated, the slip surface which the safety factor is smallest is the most dangerous sliding surface. This method is different from the previous limit equilibrium method. For the previous limit equilibrium method, the normal and tangential stresses along the sliding surface are calculated based on many assumptions. While, the limit equilibrium method proposed in this paper has fewer assumptions and clear physical meaning.

Some difficulties associated with the limit equilibrium method of slices

1983 ◽  
Vol 20 (4) ◽  
pp. 661-672 ◽  
Author(s):  
R. K. H. Ching ◽  
D. G. Fredlund
Keyword(s):  
Slope Stability ◽  
Factor Of Safety ◽  
Limit Equilibrium ◽  
Stability Limit ◽  
Limit Equilibrium Method ◽  
Soil Conditions ◽  
Side Force ◽  
Limit Equilibrium Methods ◽  
Equilibrium Method ◽  
The Stability

Several commonly encountered problems associated with the limit equilibrium methods of slices are discussed. These problems are primarily related to the assumptions used to render the inherently indeterminate analysis determinate. When these problems occur in the stability computations, unreasonable solutions are often obtained. It appears that problems occur mainly in situations where the assumption to render the analysis determinate seriously departs from realistic soil conditions. These problems should not, in general, discourage the use of the method of slices. Example problems are presented to illustrate these difficulties and suggestions are proposed to resolve these problems. Keywords: slope stability, limit equilibrium, method of slices, factor of safety, side force function.

Sign in / Sign up

Export Citation Format

Share Document