Abrasion resistance of silica-reinforced decorative laminates Part 1 — examination of the standard testing method

Wear ◽  
1976 ◽  
Vol 39 (1) ◽  
pp. 83-100 ◽  
Author(s):  
S.H. Rhee ◽  
J.H. Dumbleton
2021 ◽  
Vol 5 (3) ◽  
Author(s):  
Trevor J Steele ◽  
Clodualdo C Maningat ◽  
Paul A Seib ◽  
Mark D Haub ◽  
Sara K Rosenkranz

ABSTRACT Background To investigate the effect of resistant starch (RS) on acute glycemic or insulinemic responses, the FDA indicates that control and RS-enriched foods must contain equivalent amounts of digestible carbohydrate. However, RS-containing foods typically contain less digestible carbohydrate per serving than control foods. Thus, controlling for digestible carbohydrate may yield different responses as compared with controlling for serving size. Objective The aim was to compare the postprandial metabolic responses to native wheat starch (NWS) versus RS type 4 (RS4) using digestible carbohydrate–matched portions compared with weight-matched portions. Methods A single-blind, randomized-controlled crossover trial examined glycemic and insulinemic responses over 2 h following consumption of 4 cracker conditions and a dextrose beverage in apparently healthy participants (n = 14). Crackers provided 50 g of digestible carbohydrate using the FDA's meal-intervention protocol or 35 g of carbohydrate by weight for the marketplace substitution method. Crackers differed only by the type of starch additive: NWS (MidsolTM 50; MGP Ingredient, Inc.) or RS4 (Fibersym® RW; MGP Ingredients, Inc.). Glucose concentrations were assessed at baseline and at 15, 30, 45, 60, 90, and 120 min; insulin concentrations were measured at baseline and 30, 60, and 120 min. Results There were no significant differences between 50 g digestible carbohydrate cracker conditions for glucose or insulin incremental AUC (iAUC). The 35 g carbohydrate by weight conditions were not different for glucose iAUC [mean (95% CI): 35 g NWS: 1317 (677, 2169); 35 g RS4: 701 (262, 1351); P > 0.05]. However, insulin iAUC was lower following 35 g RS4 compared with 35 g NWS [35 g RS4: 92 (1, 259); 35 g NWS: 697 (397, 1080); P < 0.01]. Conclusions In healthy adults, consumption of RS4 crackers decreased postprandial insulin responses compared with NWS crackers when using the marketplace substitution method compared with the FDA standard testing method, with similar postprandial glucose responses. Comparisons of the FDA standard testing method and the marketplace substitution method should be investigated further to elucidate differential physiological impacts on consumers.


Author(s):  
Geoffrey M. Spinks ◽  
Shannon Bakarich ◽  
Shazed Aziz ◽  
Bidita Salahuddin ◽  
Hai Xin

Standards ◽  
2021 ◽  
Vol 1 (2) ◽  
pp. 117-133
Author(s):  
Monika Bleszynski ◽  
Edward Clark

Ice accretion is a serious problem in cold climates, causing automobile and airplane accidents, as well as severe economic losses throughout various sectors. To combat these issues, many solutions have been developed, such as de-icing materials, which can delay or prevent the adhesion of ice to a surface through chemical, temperature, or physical means. To effectively assess the properties of a de-icing material, ice adhesion testing must be conducted, of which there are numerous types, each with their own characteristics. Unfortunately, the same material, tested with different methods, may provide very different ice adhesion values. This makes it difficult to properly characterize a material’s de-icing properties and compare values across the literature. In this review, we identified the main ice adhesion testing methods and compared ice adhesion values for a particular material with different testing methods. We then discussed some of the main issues with current ice testing methods and identified some of the main factors that may affect ice adhesion values, namely ice quality and the use of a mold, which may significantly affect the final ice adhesion results. Finally, we proposed a new, simple standard testing method, in an attempt to eliminate some of the issues with current ice testing methods.


1991 ◽  
Vol 113 (4) ◽  
pp. 230-234 ◽  
Author(s):  
H. Yoshida ◽  
T. Ogasa ◽  
M. Uemura

The two-dimensional stress distributions in orthotopic composite beam under 4-point flexure are analyzed by replacing the concentrated load by distributing pressure in the vicinity of loading nose and by expanding the stress function for compatability equation in terms of Fourier series. The validity of analytical results is verified experimentally by using the photoelastic film-coating technique on unidirectional reinforced plastics. It is shown that the local stress distributions around the loading points are complicated and are very different from those predicted by elementary beam theory; and hence, the reliability of flexural strength and interlaminar shear strength defined by elementary beam theory are in question. It is suggested that the 4-point flexure is reasonable and recommendable as a standard testing method compared with the 3-point flexural one.


Diagnostics ◽  
2020 ◽  
Vol 10 (4) ◽  
pp. 224 ◽  
Author(s):  
Ting Yang ◽  
Mattia Gentile ◽  
Ching-Fen Shen ◽  
Chao-Min Cheng

The current standard testing method for screening coronavirus disease 2019 (COVID-19) is through reverse real-time PCR assay (rRT-PCR), a common molecular-based assay that requires an average of four to six hours to provide results [...]


Sign in / Sign up

Export Citation Format

Share Document