Influence of Specimen Orientation on Low-temperature Fracture Behavior of Low Carbon Steel Plate

1989 ◽  
pp. 1089-1094
Author(s):  
Z. Huang ◽  
M. Yao
Keyword(s):  
Carbon Steel ◽  
Low Temperature ◽  
Fracture Behavior ◽  
Steel Plate ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Temperature Fracture ◽  
Specimen Orientation

scholarly journals Effect of Microstructure on Low-Temperature Fracture Toughness of a Submerged-Arc-Welded Low-Carbon and Low-Alloy Steel Plate

Metals ◽  
2021 ◽  
Vol 11 (11) ◽  
pp. 1839
Author(s):  
Byeong Chan Choi ◽  
Byoungkoo Kim ◽  
Byung Jun Kim ◽  
Yong-Wook Choi ◽  
Sang Joon Lee ◽  
...  
Keyword(s):  
Low Temperature ◽  
Fracture Behavior ◽  
Steel Plate ◽  
Low Carbon Steel ◽  
Low Carbon ◽  
Temperature Fracture ◽  
Temperature Impact ◽  
Ebsd Technique ◽  
The Relationship ◽  
Submerged Arc

This study investigated the low-temperature fracture behavior of an 80-mm-thick low-carbon steel plate welded by submerged arc. The relationship between impact absorbed energy and ductility–brittle transition temperature (DBTT) based on the microstructures was evaluated through quantitative analysis on grain size and complex constituent phases using advanced EBSD technique. The microstructure formed differently depending on the heat affections, which determined fracture properties in a low-temperature environment. Among the various microstructures of the heat-affected zone (HAZ), acicular ferrite has the greatest resistance to low-temperature impact due to its fine interlocking formation and its high-angle grain boundaries.

Factors Influencing Dephosphorization of Low Carbon Steel in Converter

2021 ◽  
Vol 1047 ◽  
pp. 111-119
Author(s):  
Zhao Liu ◽  
Shu Sen Cheng ◽  
Liang Wang
Keyword(s):  
Carbon Steel ◽  
Low Temperature ◽  
Slag Composition ◽  
Phosphorus Content ◽  
Low Carbon Steel ◽  
Smelting Process ◽  
Low Carbon ◽  
Factors Influencing ◽  
High Basicity ◽  
Metal Yield

A 300-metric ton converter in a steel plant in China was studied. The influence of factors such as slag composition and temperature in the smelting process on the dephosphorization effect was statistically analyzed. The dephosphorization ability of slag increased firstly and then decreased with the increase of temperature, basicity and FeO content. Low-temperature, high-basicity and high-oxidizing slag are thermodynamically beneficial to promote the dephosphorization reaction, but the basicity is higher than 4.0, and the temperature is higher than 1640 °C are not conducive to the slag to obtain better fluidity. At the same time, too high FeO content will increase the activity coefficient of P2O5, thereby increasing its activity, which is not conducive to the progress of the dephosphorization reaction. As the end point content of carbon decreases, the oxygen content increases and the phosphorus content decreases. A very low carbon content is not conducive to metal yield and temperature control.

scholarly journals Evaluation of induced residual stresses on AISI 1020 low carbon steel plate from experimental and FEM approach during TIG welding process

2019 ◽  
Vol 13 (1) ◽  
pp. 4415-4433
Author(s):  
I. B. Owunna ◽  
A. E. Ikpe
Keyword(s):  
Carbon Steel ◽  
Residual Stresses ◽  
Steel Plate ◽  
Low Carbon Steel ◽  
Welding Process ◽  
Service Condition ◽  
Tig Welding ◽  
Von Mises Stress ◽  
Low Carbon ◽  
Temperature Range

Induced residual stresses on AISI 1020 low carbon steel plate during Tungsten Inert Gas (TIG) welding process was evaluated in this study using experimental and Finite Element Method (FEM). The temperature range measured from the welding experimentation was 251°C-423°C, while the temperature range measured from the FEM was 230°C-563°C; whereas, the residual stress range measured from the welding experimentation was 144MPa-402Mpa, while the residual range measured from the FEM was 233-477MPa respectively. Comparing the temperature and stress results obtained from both methods, it was observed that the range of temperature and residual stresses measured were not exactly the same due to the principles at which both methods operate but disparities between the methods were not outrageous. However, these values can be fed back to optimization tools to obtain optimal parameters for best practices.  Results of the induced stress distribution was created from a static study where the thermal results were used as loading conditions and it was observed that the temperature increased as the von-Mises stress increased, indicating that induced stresses in welded component may hamper the longevity of such component in service condition. Hence, post-weld heat treatment is imperative in order to stress relieve metals after welding operation and improve their service life.

Effect of Sol-Gel Film on the Corrosion Resistance of Low Carbon Steel Plate

2020 ◽  
Vol 984 ◽  
pp. 43-50
Author(s):  
Hua Yuan Zhang ◽  
Can Wang ◽  
Bing Xue ◽  
Jing Luo
Keyword(s):  
Corrosion Resistance ◽  
Carbon Steel ◽  
Steel Plate ◽  
Salt Spray ◽  
Sol Gel ◽  
Low Carbon Steel ◽  
Corrosion Current ◽  
Neutral Salt ◽  
Low Carbon ◽  
Gel Film

To improve the corrosion resistance on Q235 low carbon steel, in this paper, tetraethyl orthosilicate (TEOS), N-dodecyl trimethoxysilane and γ-(2,3-epoxypropoxy) propytrimethoxysilane (KH560) were used to make organic-inorganic hybrid sol-gel film. Cross cut test adhesion method, neutral salt spray test, electrochemical test and film protective efficiency were taken to value the corrosion resistance property. The corrosion topography was studied by optical microscope. In addition, potentiodynamic polarization, electrochemical impedance spectroscopy (EIS) curves and equivalent electric circuit fitting were used to analyze the corrosion mechanism. The cross cut adhesion of sol-gel film can reach 1 class and the protection class can attain 5 class after 72 hours neutral salt spray test. According to the potentiodynamic polarization curve analysis, the corrosion potential of sol-gel film coating sample after 0.5 hours immersion was -0.46 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.74×10-7 A·cm-2. The corrosion potential of bare Q235 low carbon steel plate after 0.5 hours immersion was -0.78 V (vs. SCE) on the 0.1 Hz, and its corrosion current density was 4.75×10-6 A·cm-2. The impedance value on 0.1 Hz (|Z|0.1Hz) (1.27×106 Ω·cm2) of sol-gel film coating sample was more than three orders of magnitude higher than the value of the low carbon steel plate. Even dipping in 3.5 wt. % NaCl for 72 hours, the |Z|0.1Hz value of sol-gel coating sample was still one order of magnitude higher than the low carbon steel plate with 0.5 hours immersion. Sol-gel film with excellent adhesion can significantly improve the corrosion resistance of low carbon steel plate. Sol-gel film can increase the protection efficiency of low carbon steel plate by 90%.

scholarly journals An answer to the carbon cluster in low-temperature aged ferritic low-carbon steel

2020 ◽  
Vol 159 ◽  
pp. 110006 ◽  
Author(s):  
Takuya Maeda ◽  
Yasuhito Kawahara ◽  
Keisuke Kinoshita ◽  
Hideaki Sawada ◽  
Jun Takahashi ◽  
...  
Keyword(s):  
Carbon Steel ◽  
Low Temperature ◽  
Low Carbon Steel ◽  
Carbon Cluster ◽  
Low Carbon
Sign in / Sign up

Export Citation Format

Share Document