Sustainable production of cellulose nanofiber gels and paper from sugar beet waste using enzymatic pre-treatment

2020 ◽  
Vol 230 ◽  
pp. 115581 ◽  
Author(s):  
Alixander Perzon ◽  
Bodil Jørgensen ◽  
Peter Ulvskov
2012 ◽  
Vol 66 (5) ◽  
pp. 743-748 ◽  
Author(s):  
Vladimir Filipovic ◽  
Biljana Curcic ◽  
Milica Nicetin ◽  
Dragana Plavsic ◽  
Gordana Koprivica ◽  
...  

The effects of osmotic dehydration on mass transfer properties and microbiological profile were investigated in order to determine the usefulness of this technique as pre-treatment for further treatment of meat. Process was studied in two solutions (sugar beet molasses, and aqueous solution of sodium chloride and sucrose), at two temperatures (4 and 22?C) at atmospheric pressure. The most significant parameters of mass transfer were determined after 300 minutes of the dehydration. The water activity (aw) values of the processed meat were determined, as well as the change of the microbiological profile between the fresh and dehydrated meat. At the temperature of 22?C the sugar beet molasses proved to be most suitable as an osmotic solution, despite the greater viscosity.


2021 ◽  
Vol 173 ◽  
pp. 114084
Author(s):  
Sepideh Haroni ◽  
Hassan Zaki Dizaji ◽  
Houshang Bahrami ◽  
María González Alriols

Author(s):  
Elena Subbotina ◽  
Céline Montanari ◽  
Peter Olsén ◽  
Lars A Berglund

Design of nanocellulose-based composite materials suitable for selective disintegration, recovery and recycling of individual components is of great scientific and technical interest. Cellulose nanofiber/epoxy (CNF/EP) composites are candidate bio-based substitutes...


2008 ◽  
Vol 58 (9) ◽  
pp. 1857-1863 ◽  
Author(s):  
M. Seppälä ◽  
T. Paavola ◽  
A. Lehtomäki ◽  
O. Pakarinen ◽  
J. Rintala

The objective of this research was to evaluate the biogas production from crops in boreal conditions, focusing on the optimal pre-treatment and storage methods, co-digestion and energy balance of farm-scale crop based biogas plants. Alkaline treatments offered some potential for improving the methane yield from grass and sugar beet tops. The results show that the CH4 yield of energy crops can be maintained by appropriate ensiling conditions for even after 11 months in ambient conditions. The CH4 yield was best preserved with wet grass mixture without additives. Co-digestion of manure and crops was shown to be feasible with feedstock volatile solids (VS) containing up to 40% of crops. The highest specific methane yields of 268, 229 and 213 l CH4 kg−1 VSadded in co-digestion of cow manure with grass, sugar beet tops and straw, respectively, were obtained during feeding with 30% of crop in the feedstock, corresponding to 85–105% of the total methane potential in the substrates as determined by batch assays. The energy output:input ratio of farm-scale grass silage based biogas plant varied significantly (3.5–8.2) with different assumptions and system boundaries being lowest when using only inorganic fertilizers and highest when half of the heat demand of the system could be covered by metabolic heat.


Author(s):  
О. В. Ківа ◽  
В. В. Грибініченко

Були проведені експериментальні дослідження для визначення впливу попередньої ультразвукової обробки води на схожість та енерґію проростання насіння цук-рового буряка. Крім того проводились експеримента-льні дослідження із вивчення впливу тривалості уль-тразвукової обробки на енерґію проростання. Пода-ються результати проведених експериментальних випробувань та одержані характеристики процесу проростання насіння в звичайній воді з міського водо-гону та у воді, яку попередньо піддавали ультразву-ковій обробці, проводиться їх порівняльний аналіз. Experimental studies have been conducted to determine the effect of ultrasonic pre-treatment of water on germination and vigor of seeds of sugar beet. Experimental studies have been conducted to determine the effect of duration of ultrasonic treatment on vigor. Served results of experimental tests and obtained characteristics of the process of seed germination of plain water from the municipal water supply and water that previously was subjected to ultrasonic treatment and a comparative analysis are conducted.


Agronomy ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 763 ◽  
Author(s):  
Zahra Salimi ◽  
Birte Boelt

Endogenous inhibitors have a crucial effect on the success of sugar beet (Beta vulgaris) seed germination. The strength of this effect changes during seed maturation, and washing away these inhibitors can facilitate germination. Investigation of various washing factors such as water-to-seed ratio, stirring time, and speed of stirring on a mixed-maturity lot of sugar beet seeds revealed the significant effect of the interaction of all factors. Seeds with different maturity classes, from the same lot, were washed using procedures determined from the first experiment. Statistical analysis of the germination data of the washed seeds showed a significant difference in mean germination time depending on maturity class. Washing seeds of different maturity classes with 40 mL of water per gram of seed improved the germination performance of maturity classes 2 and 5, compared with 20 mL water per gram of seed. The UV absorbance of inhibitors washed from seeds differed between maturity classes. The change in seed moisture content during the washing process is another factor altered by the extent of seed development, and this variation in water uptake may reflect the pericarp structure of seed in different maturity classes. The findings in this manuscript highlight the importance of optimizing the pre-treatment procedures in accordance with the individual seed lot.


Author(s):  
E Y. Wang ◽  
J. T. Cherian ◽  
A. Madsen ◽  
R. M. Fisher

Many steel parts are electro-plated with chromium to protect them against corrosion and to improve their wear-resistance. Good adhesion of the chrome plate to the steel surface, which is essential for long term durability of the part, is extremely dependent on surface preparation prior to plating. Recently, McDonnell Douglas developed a new pre-treatment method for chrome plating in which the steel is anodically etched in a sulfuric acid and hydrofluoric acid solution. On carbon steel surfaces, this anodic pre-treatment produces a dark, loosely adhering material that is commonly called the “smut” layer. On stainless steels and nickel alloys, the surface is only darkened by the anodic pre-treatment and little residue is produced. Anodic pre-treatment prior to hard chrome plating results in much better adherence to both carbon and alloy steels.We have characterized the anodic pre-treated steel surface and the resulting “smut” layer using various techniques including electron spectroscopy for chemical analysis (ESCA) on bulk samples and transmission electron microscopy (TEM) and electron energy-loss spectroscopy (EELS) on stripped films.


Sign in / Sign up

Export Citation Format

Share Document