Manufacturing of high-toughness Al–Si alloy by rolling and friction stir processing: Effect of traverse speed

2022 ◽  
Vol 37 ◽  
pp. 19-36
Author(s):  
Mehdi Soleymanpour ◽  
Hamed Jamshidi Aval ◽  
Roohollah Jamaati
Keyword(s):  
Friction Stir Processing ◽  
Traverse Speed ◽  
Friction Stir ◽  
High Toughness ◽  
Processing Effect

Influence of Process Parameters on Microstructure of Friction Stir Processed Mg AZ31 Alloy

2017 ◽  
pp. 1293-1305
Author(s):  
G. Venkateswarlu ◽  
M.J. Davidson ◽  
G.R.N. Tagore ◽  
P. Sammaiah
Keyword(s):  
Plastic Deformation ◽  
Grain Refinement ◽  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Homogeneous Microstructure ◽  
Friction Stir ◽  
Tool Tilt Angle

Friction stir processing (FSP) has been developed on the principles of friction stir welding (FSW) as an effective and efficien new method for grain refinement and microstructural modification, providing intense plastic deformation as well as higher strain rates than other conventional severe plastic deformation methods. FSP produces an equiaxed homogeneous microstructure consisting of fine grains, resulting in the enhancement of the properties of the material at room temperature. The objective of the present paper is to examine the influence of friction stir processing (FSP) parameters namely tool rotational speed (RS), tool traverse speed (TS) and tool tilt angle (TA) on the microstructures of friction stir processed AZ31B-O magnesium alloy. This investigation has focused on the microstructural changes occurred in the dynamically recrystallised nugget zone/ stir zone and the thermo mechanically affected zone during FSP. The results presented in this work indicate that all the three FSP process parameters have a significant effect on the resulting microstructure and also found that the rotational speed has greatly influenced the homogenization of the material. The grain refinement is higher at intermediate rotational speed (1150 rpm), traverse speed (32 mm / min and tilt angle (10). It is established that FSP can be a good grain refinement method for improving the properties of the material.

Friction Stir Processing: An Operational Method to Improve Ductility in Pure Copper

2013 ◽  
Vol 818 ◽  
pp. 14-19 ◽  
Author(s):  
Vahid Rezazadeh ◽  
Ali Sharbatzadeh ◽  
Ali Hosseinzadeh ◽  
Amir Safari ◽  
Salar Salahi
Keyword(s):  
Friction Stir Processing ◽  
Rotational Speed ◽  
Pure Copper ◽  
Traverse Speed ◽  
Ultrafine Grain ◽  
Work Piece ◽  
Cavity Formation ◽  
Nugget Zone ◽  
Friction Stir ◽  
Lower Heat

mproving ductility in metals using friction stir processing (FSP) is a challenging effort and is made by means of a rotating tool inserted in a work piece providing heat transfer and plastic deformation. In this investigation, improving ductility during FSP was determined as a purpose and the microstructure and mechanical properties of nugget zone were investigated during friction stir processing (FSP) of pure copper. Ductility was measured using tensile elongations at a temperature of 20 °C. By varying the traverse speed from 40 to 100 mm/min at rotation speeds of 300 and 600 rpm, the ultrafine grain microstructure was achieved .Defects were observed in rotational speed of 300 rpm. By increasing traverse speed at constant rotational speed of 600 rpm grain size of the nugget zone decreased and ductility increased. Achievable ductility was limited by cavity formation due to lower heat input and deformation in samples with defects.

Investigations into the mechanical, morphological and thermal analyses of friction stir processing of high-density polyethylene composites

2016 ◽  
Vol 232 (7) ◽  
pp. 1193-1200 ◽  
Author(s):  
Jicheng Gao ◽  
Chao Li ◽  
Yifu Shen
Keyword(s):  
Tensile Strength ◽  
Friction Stir Processing ◽  
High Density Polyethylene ◽  
Thermal Analyses ◽  
Experimental Tests ◽  
Traverse Speed ◽  
High Density ◽  
Scanning Calorimetry ◽  
Friction Stir ◽  
Polyethylene Composites

The aim of this work is to fabricate the high-density polyethylene–copper composites by submerged friction stir processing at different traverse speeds. The scanning electron microscopy is used to analyze the distribution of microstructure and particles. The experimental results indicated that the macrostructure morphology, microstructure and tensile strength vary depending on the traverse speed. Compared with the pure high-density polyethylene, Cu-filled polymer composites showed lower tensile strength and higher microhardness. The maximal values of the tensile strength and microhardness were achieved at traverse speeds of 30 and 15 mm/min, respectively. The thermal properties of Cu-filled high-density polyethylene composites were studied by differential scanning calorimetry. The crystalline content of the composites was decreased due to the addition of copper. From the experimental tests, it can be concluded that submerged fiction stir processing has a great potential for producing polymer–metal composites.

Effect of Tool Rotational Speed on Microstructure and Microhardness of AA6082/TiC Surface Composites using Friction Stir Processing

2014 ◽  
Vol 592-594 ◽  
pp. 234-239 ◽  
Author(s):  
A. Thangarasu ◽  
N. Murugan ◽  
I. Dinaharan ◽  
S.J. Vijay
Keyword(s):  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Tool Rotational Speed ◽  
Friction Stir ◽  
Surface Composite ◽  
Surface Composites ◽  
Homogenous Distribution ◽  
Tool Pin ◽  
Scanning Electron

Friction stir processing (FSP) is as a novel modifying technique to synthesize surface composites. An attempt has been made to synthesis AA6082/TiC surface composite using FSP and to analyze the effect of tool rotational speed on microstructure and microhardness of the same. The tool rotational speed was varied from 800 rpm to 1600 rpm in steps of 400 rpm. The traverse speed, axial force, groove width and tool pin profile were kept constant. Scanning electron microscopy was employed to study the microstructure of the fabricated surface composites. The results indicated that the tool rotational speed significantly influenced the area of the surface composite and distribution of TiC particles. Higher rotational speed provided homogenous distribution of TiC particles while lower rotational speed caused poor distribution of TiC particles in the surface composite. The effect of the tool rotational speed on microhardness is also reported in this paper.

Influence of Friction Stir Processing Parameters on the Fabrication of SiC/316L Surface Composite

2010 ◽  
Vol 297-301 ◽  
pp. 221-226 ◽  
Author(s):  
R. Salekrostam ◽  
M.K. Besharati Givi ◽  
P. Asadi ◽  
P. Bahemmat
Keyword(s):  
Stainless Steel ◽  
Friction Stir Processing ◽  
Traverse Speed ◽  
Processing Parameters ◽  
Fusion Welding ◽  
Welding Parameters ◽  
Stainless Steel 316L ◽  
Friction Stir ◽  
The Many ◽  
Welding Processes

Compared to the many fusion welding processes that are routinely used for joining stainless steel 316L, the friction stir welding (FSW) process is an emerging solid state joining process in which the material that is being welded does not melt and is being recast. The welding parameters play a major role in deciding the weld quality. In this investigation an attempt has been made to understand the influences of rotational speed and traverse speed of the tool on the microstructure of the friction stir processing zone in stainless steel 316L. Five different tool rotational speeds have been used to fabricate the joints at four different traverse speeds from this investigation which is the optimum for the tool speed and higher or lower amounts of these parameters are not useful for the process.

WEAR ANALYSIS OF ALUMINUM–NICKEL INTERMETALLIC SURFACE COMPOSITE FABRICATED BY FRICTION STIR PROCESSING

2020 ◽  
pp. 2050057
Author(s):  
MORTEZA SHAMANIAN ◽  
MOHAMMAD REZA NASRESFAHANI ◽  
EBRAHIM BAHRAMI ◽  
HOSSEIN EDRIS
Keyword(s):  
Wear Resistance ◽  
Friction Stir Processing ◽  
Traverse Speed ◽  
Friction Stir ◽  
Surface Composite ◽  
Wear Analysis ◽  
2024 Alloy ◽  
Ni Powder ◽  
The Matrix ◽  
Stable Stage

In low-strength metals, the main purpose of enhancing surface properties is to increase the abrasion resistance. One of the new methods for improving the microstructure of the surface layer of metals is the surface composite. In this research, the friction stir processing (FSP) was used to develop an aluminum–nickel intermetallic surface composite. Aluminum 2024 alloy and Ni powder were used as the matrix and reinforcement agent, respectively. Comparison of composite and non-composite FSP samples indicates that adding reinforcements improves the wear resistance of a monolithic metal in all condition. Also, the wear resistance of fabricated composites using activated Al–Ni powder is higher than the others due to the presence of Al3Ni2 and Al3Ni intermetallic compounds. At low traverse speed of the FSP, powder agglomeration occurs, and the powders are not uniformly distributed, as a result, the friction coefficient rises. SEM micrographs of scratched particles of activated composite confirm the delamination mechanism in the wear stable stage.

Influence of Process Parameters on Microstructure of Friction Stir Processed Mg AZ31 Alloy

2014 ◽  
Vol 2 (1) ◽  
pp. 47-58
Author(s):  
G. Venkateswarlu ◽  
M.J. Davidson ◽  
G.R.N. Tagore ◽  
P. Sammaiah
Keyword(s):  
Plastic Deformation ◽  
Grain Refinement ◽  
Process Parameters ◽  
Tilt Angle ◽  
Friction Stir Processing ◽  
Rotational Speed ◽  
Traverse Speed ◽  
Homogeneous Microstructure ◽  
Influence Of Process Parameters ◽  
Friction Stir

Friction stir processing (FSP) has been developed on the principles of friction stir welding (FSW) as an effective and efficien new method for grain refinement and microstructural modification, providing intense plastic deformation as well as higher strain rates than other conventional severe plastic deformation methods. FSP produces an equiaxed homogeneous microstructure consisting of fine grains, resulting in the enhancement of the properties of the material at room temperature. The objective of the present paper is to examine the influence of friction stir processing (FSP) parameters namely tool rotational speed (RS), tool traverse speed (TS) and tool tilt angle (TA) on the microstructures of friction stir processed AZ31B-O magnesium alloy. This investigation has focused on the microstructural changes occurred in the dynamically recrystallised nugget zone/ stir zone and the thermo mechanically affected zone during FSP. The results presented in this work indicate that all the three FSP process parameters have a significant effect on the resulting microstructure and also found that the rotational speed has greatly influenced the homogenization of the material. The grain refinement is higher at intermediate rotational speed (1150 rpm), traverse speed (32 mm / min and tilt angle (10). It is established that FSP can be a good grain refinement method for improving the properties of the material.

Sign in / Sign up

Export Citation Format

Share Document