Silanization of heat-treated halloysite nanotubes using γ-aminopropyltriethoxysilane

2019 ◽  
Vol 180 ◽  
pp. 105204 ◽  
Author(s):  
Shiyu Jia ◽  
Mingde Fan
Keyword(s):  
Halloysite Nanotubes ◽  
Heat Treated

Effects of heat-treated HNTs on the mechanical properties of GFRP under moisture absorption

2018 ◽  
Vol 32 (19) ◽  
pp. 1840070 ◽  
Author(s):  
Y. H. Kim ◽  
S. J. Park ◽  
J. S. Choi ◽  
K. M. Moon ◽  
C. W. Bae
Keyword(s):  
Mechanical Properties ◽  
Moisture Absorption ◽  
Halloysite Nanotubes ◽  
Glass Fiber Reinforced Plastic ◽  
Fiber Reinforced Plastic ◽  
Humid Environment ◽  
Glass Fiber Reinforced ◽  
Reinforced Plastic ◽  
Heat Treated ◽  
Interlaminar Shear

In this study, halloysite nanotubes (HNTs) were heat-treated at various temperatures in order to minimize particle aggregation, and the mechanical properties in the humid environment was compared and analyzed to prevent the pore formation and achieve an optimal bonding with epoxy resin. As a result, the glass fiber-reinforced plastic (GFRP), with 0.5 wt.% heat-treated HNT at 700[Formula: see text]C, showed the highest moisture absorption resistance, tensile strength and interlaminar shear strength.

Controlled release of losartan from acid- and heat-treated halloysite nanotubes

2018 ◽  
Vol 28 (2) ◽  
pp. 160-168 ◽  
Author(s):  
Farid Moeinpour ◽  
Faezeh Soofivand ◽  
Fatemeh S. Mohseni-Shahri
Keyword(s):  
Controlled Release ◽  
Halloysite Nanotubes ◽  
Heat Treated

J0450205 Impact Property of Unsaturated Polyester Containing Halloysite Nanotubes Heat-treated at Various Temperatures

2015 ◽  
Vol 2015 (0) ◽  
pp. _J0450205--_J0450205-
Author(s):  
Soo-Jeong PARK ◽  
Antonio Norio NAKAGAITO ◽  
Yun-Hae KIM ◽  
Hitoshi TAKAGI
Keyword(s):  
Unsaturated Polyester ◽  
Halloysite Nanotubes ◽  
Impact Property ◽  
Heat Treated

Characterization studies of heat-treated halloysite nanotubes

2020 ◽  
Vol 74 (12) ◽  
pp. 4547-4557 ◽  
Author(s):  
M. Türkay Aytekin ◽  
Halit L. Hoşgün
Keyword(s):  
Halloysite Nanotubes ◽  
Heat Treated ◽  
Characterization Studies

Direct Observation of Crystalline Ordering In Naturally Graphitized Carbon Produced by Low Grade Metamorphism

1977 ◽  
Vol 35 ◽  
pp. 162-163
Author(s):  
Thomas R. McKee ◽  
Peter R. Buseck
Keyword(s):  
Crystallite Size ◽  
Sedimentary Rocks ◽  
Carbonaceous Material ◽  
Low Grade ◽  
X Ray ◽  
Graphitized Carbon ◽  
Transmission Electron ◽  
Heat Treated ◽  
Commercial Carbon ◽  
Metamorphic Zone

Sediments commonly contain organic material which appears as refractory carbonaceous material in metamorphosed sedimentary rocks. Grew and others have shown that relative carbon content, crystallite size, X-ray crystallinity and development of well-ordered graphite crystal structure of the carbonaceous material increases with increasing metamorphic grade. The graphitization process is irreversible and appears to be continous from the amorphous to the completely graphitized stage. The most dramatic chemical and crystallographic changes take place within the chlorite metamorphic zone.The detailed X-ray investigation of crystallite size and crystalline ordering is complex and can best be investigated by other means such as high resolution transmission electron microscopy (HRTEM). The natural graphitization series is similar to that for heat-treated commercial carbon blacks, which have been successfully studied by HRTEM (Ban and others).

Effect of Shock Loading on the Microstructure of Uniloy 326

1974 ◽  
Vol 32 ◽  
pp. 504-505
Author(s):  
K. P. Staudhammer ◽  
L. E. Murr
Keyword(s):  
Grain Size ◽  
Shock Loading ◽  
Current Investigation ◽  
Two Phase ◽  
05 C ◽  
Shock Deformation ◽  
Heat Treated

The effect of shock loading on a variety of steels has been reviewed recently by Leslie. It is generally observed that significant changes in microstructure and microhardness are produced by explosive shock deformation. While the effect of shock loading on austenitic, ferritic, martensitic, and pearlitic structures has been investigated, there have been no systematic studies of the shock-loading of microduplex structures.In the current investigation, the shock-loading response of millrolled and heat-treated Uniloy 326 (thickness 60 mil) having a residual grain size of 1 to 2μ before shock loading was studied. Uniloy 326 is a two phase (microduplex) alloy consisting of 30% austenite (γ) in a ferrite (α) matrix; with the composition.3% Ti, 1% Mn, .6% Si,.05% C, 6% Ni, 26% Cr, balance Fe.

Phase Transformation In Ti-6al-4v Alloys

1972 ◽  
Vol 30 ◽  
pp. 584-585
Author(s):  
Shiro Fujishiro
Keyword(s):  
Phase Transformation ◽  
Grain Boundary ◽  
Cryogenic Temperature ◽  
Β Phase ◽  
Heat Treated ◽  
Mixed Microstructure ◽  
Ductile Behavior

The Ti-6 wt.% Al-4 wt.% V commercial alloys have exhibited an improved formability at cryogenic temperature when the alloys were heat-treated prior to the tests. The author was interested in further investigating this unusual ductile behavior which may be associated with the strain-induced transformation or twinning of the a phase, enhanced at lower temperatures. The starting materials, supplied by RMI Co., Niles, Ohio were rolled mill products in the form of 40 mil sheets. The microstructure of the as-received materials contained mainly ellipsoidal α grains measuring between 1 and 5μ. The β phase formed an undefined grain boundary around the a grains. The specimens were homogenized at 1050°C for one hour, followed by aging at 500°C for two hours, and then quenched in water to produce the α/β mixed microstructure.

Microstructural Evolution in Reduced TiO2

1981 ◽  
Vol 39 ◽  
pp. 74-75
Author(s):  
W. T. Donlon ◽  
S. Shinozaki ◽  
E. M. Logothetis ◽  
W. Kaizer
Keyword(s):  
Microstructural Evolution ◽  
Point Defects ◽  
Extended Defects ◽  
Small Deviations ◽  
Controlled Atmospheres ◽  
Limited Solubility ◽  
Thin Foils ◽  
Heat Treated ◽  
Porous Polycrystalline ◽  
Crystallographic Shear

Since point defects have a limited solubility in the rutile (TiO2) lattice, small deviations from stoichiometry are known to produce crystallographic shear (CS) planes which accomodate local variations in composition. The material used in this study was porous polycrystalline TiO2 (60% dense), in the form of 3mm. diameter disks, 1mm thick. Samples were mechanically polished, ion-milled by conventional techniques, and initially examined with the use of a Siemens EM102. The electron transparent thin foils were then heat-treated under controlled atmospheres of CO/CO2 and H2 and reexamined in the same manner.The “as-received” material contained mostly TiO2 grains (∼5μm diameter) which had no extended defects. Several grains however, aid exhibit a structure similar to micro-twinned grains observed in reduced rutile. Lattice fringe images (Fig. 1) of these grains reveal that the adjoining layers are not simply twin related variants of a single TinO2n-1 compound. Rather these layers (100 - 250 Å wide) are alternately comprised of stoichiometric TiO2 (rutile) and reduced TiO2 in the form of Ti8O15, with the Ti8O15 layers on either side of the TiO2 being twin related.

Characterization of carbides in M50NiL

1991 ◽  
Vol 49 ◽  
pp. 606-607
Author(s):  
L. S. Lin ◽  
K. P. Gumz ◽  
A. V. Karg ◽  
C. C. Law
Keyword(s):  
Temperature Effects ◽  
Base Composition ◽  
Lattice Parameter ◽  
Control Surface ◽  
Carbide Formation ◽  
Particle Sizes ◽  
Low Carbon ◽  
Fee Structure ◽  
Heat Treated

Carbon and temperature effects on carbide formation in the carburized zone of M50NiL are of great importance because they can be used to control surface properties of bearings. A series of homogeneous alloys (with M50NiL as base composition) containing various levels of carbon in the range of 0.15% to 1.5% (in wt.%) and heat treated at temperatures between 650°C to 1100°C were selected for characterizations. Eleven samples were chosen for carbide characterization and chemical analysis and their identifications are listed in Table 1.Five different carbides consisting of M6C, M2C, M7C3 and M23C6 were found in all eleven samples examined as shown in Table 1. M6C carbides (with least carbon) were found to be the major carbide in low carbon alloys (<0.3% C) and their amounts decreased as the carbon content increased. In sample C (0.3% C), most particles (95%) encountered were M6C carbide with a particle sizes range between 0.05 to 0.25 um. The M6C carbide are enriched in both Mo and Fe and have a fee structure with lattice parameter a=1.105 nm (Figure 1).

Formation Mechanisms for Multiply Twinned Particles During Nucleation in the Au/MICA System

1975 ◽  
Vol 33 ◽  
pp. 84-85
Author(s):  
Eal H. Lee ◽  
Helmut Poppa
Keyword(s):  
Deposition Time ◽  
High Vacuum ◽  
Dark Field ◽  
Ultra High Vacuum ◽  
Formation Mechanisms ◽  
Heat Treated ◽  
Cluster Density ◽  
Diffraction Patterns ◽  
Crystal Particle ◽  
Multiply Twinned Particles

The formation of thin films of gold on mica has been studied in ultra-high vacuum (5xl0-10 torr) . The mica substrates were heat-treated for 24 hours at 375°C, cleaved, and annealed for 15 minutes at the deposition temperature of 300°C prior to deposition. An impingement flux of 3x1013 atoms cm-2 sec-1 was used. These conditions were found to give high number densities of multiple twin particles and are based on a systematic series of nucleation experiments described elsewhere. Individual deposits of varying deposition time were made and examined by bright and dark field TEM after "cleavage preparation" of highly transparent specimens. In the early stages of growth, the films generally consist of small particles which are either single crystals or multiply twinned; a strong preference for multiply twinned particles was found whenever the particle number densities were high. Fig. 1 shows the stable cluster density ns and the variation with deposition time of multiple twin particle and single crystal particle densities, respectively. Corresponding micrographs and diffraction patterns are shown in Fig. 2.

Sign in / Sign up

Export Citation Format

Share Document