Biocarbon from spent coffee ground and their sustainable biocomposites with recycled water bottle and bale wrap: A new life for waste plastics and waste food residues for industrial uses

2021 ◽  
pp. 106759
Author(s):  
Arvind Gupta ◽  
Amar K. Mohanty ◽  
Manjusri Misra
Keyword(s):  
Water Bottle ◽  
Waste Plastics ◽  
Recycled Water ◽  
Spent Coffee Ground ◽  
Coffee Ground ◽  
Food Residues ◽  
Waste Food

scholarly journals Spent Coffee Ground as Low-Cost Adsorbent for Congo Red Dye Removal from Aqueous Solution

2021 ◽  
Vol 765 (1) ◽  
pp. 012089
Author(s):  
R Taufik ◽  
M Mohamad ◽  
R Wannahari ◽  
N F Shoparwe ◽  
WHW Osman ◽  
...  
Keyword(s):  
Aqueous Solution ◽  
Congo Red ◽  
Dye Removal ◽  
Low Cost ◽  
Congo Red Dye ◽  
Spent Coffee Ground ◽  
Coffee Ground ◽  
Red Dye

3D printing of spent coffee ground derived biochar reinforced epoxy composites

2021 ◽  
pp. 002199832110022
Author(s):  
Ahmed Alhelal ◽  
Zaheeruddin Mohammed ◽  
Shaik Jeelani ◽  
Vijaya K Rangari
Keyword(s):  
3D Printing ◽  
Flexural Modulus ◽  
Flexural Properties ◽  
Direct Write ◽  
Thermal And Mechanical Properties ◽  
Spent Coffee Grounds ◽  
Coffee Grounds ◽  
Spent Coffee Ground ◽  
Coffee Ground ◽  
3D Printed

Semi-crystalline carbon biochar is derived from spent coffee grounds (SCG) by a controlled pyrolysis process at high temperature/pressure conditions. Obtained biochar is characterized using XRD, SEM, and TEM techniques. Biochar particles are in the micrometer range with nanostructured morphologies. The SCG biochar thus produced is used as reinforcement in epoxy resin to 3 D print samples using the direct-write (DW) method with 1 and 3 wt. % loadings. Rheology results show that the addition of biochar makes resin viscous, enabling it to be stable soon after print; however, it could also lead to clogging of resin in printer head. The printed samples are characterized for chemical, thermal and mechanical properties using FTIR, TGA, DMA and flexure tests. Storage modulus improved with 1 wt. % biochar addition up to 27.5% and flexural modulus and strength increased up to 55.55% and 43.30% respectively. However, with higher loading of 3 wt. % both viscoelastic and flexural properties of 3D printed samples drastically reduced thus undermining the feasibility of 3D printing biochar reinforced epoxies at higher loadings.

Reinforcing Efficiency of Pyrolyzed Spent Coffee Ground in Styrene-Butadiene Rubber

2021 ◽  
Vol 29 (9) ◽  
pp. 597-604
Author(s):  
Supparoek Boopasiri ◽  
Pongdhorn Sae-Oui ◽  
Sirilug Lundee ◽  
Sukanya Takaewnoi ◽  
Chomsri Siriwong
Keyword(s):  
Styrene Butadiene Rubber ◽  
Butadiene Rubber ◽  
Spent Coffee Ground ◽  
Coffee Ground ◽  
Styrene Butadiene

scholarly journals Acute toxicity of experimental fertilizers made of blood meal, spent coffee ground and biomass ash

2017 ◽  
Vol 34 (1) ◽  
pp. 95-102 ◽  
Author(s):  
Tomasz Ciesielczuk ◽  
Czesława Rosik-Dulewska ◽  
Joanna Poluszyńska ◽  
Irena Sławińska
Keyword(s):  
Acute Toxicity ◽  
Cucumis Sativus ◽  
Plant Species ◽  
Blood Meal ◽  
Lepidium Sativum ◽  
Toxicity Tests ◽  
Cucumis Sativus L ◽  
Spent Coffee Ground ◽  
Coffee Ground ◽  
Lepidium Sativum L

Abstract The study presents the results of research on the acute toxicity of a fertilizer formulas made of spent coffee ground (SCG) with addition of ash from low-temperature combustion of biomass or ash with an admixture of magnesium sulphate and blood meal. The experimental fertilizer formulas included also rape oil used as a plasticizer for controlling the nutrients release from the fertiliser. Mustard (Sinapis alba L.), oats (Avena sativa sp. L.), cucumber (Cucumis sativus L.) and cress (Lepidium sativum L.) were used as test plants species in the experiment. The toxicity tests were performed using a standard procedure of 72 h with the use of Phytotoxkit microbiotest and fertilizer application of 2.5; 5 and 10% (v/v). The obtained results indicated an increase of acute toxicity for all tested plant species, proportionally to the applied doses of the fertilizer. During the 72 h period, the strongest inhibition of seedling growth was recorded in samples consisting of 10% of the tested fertilizers, particularly when they showed considerable level of salinity or low pH values. From the tested plant species, cress (Lepidium sativum L.) turned out to be the most sensitive to the applied fertilizers, the least was cucumber (Cucumis sativus L.) for which only a small inhibition of root system growth was observed. The inhibited growth of roots could be attributed to a reduced oxygen access and excessive salinity of the substratum caused by the applied additives.

scholarly journals Dysprosium Removal from Water Using Active Carbons Obtained from Spent Coffee Ground

2019 ◽  
Author(s):  
Lorena Alcaraz ◽  
María Esther Escudero ◽  
Francisco J. Alguacil ◽  
Irene Llorente ◽  
Ana Urbieta ◽  
...  
Keyword(s):  
Adsorption Capacity ◽  
Activated Carbons ◽  
Chemical Study ◽  
Bet Surface Area ◽  
Maximum Adsorption Capacity ◽  
Solution Ph ◽  
Microporous Material ◽  
Physico Chemical ◽  
Spent Coffee Ground ◽  
Coffee Ground

This paper describes the physico-chemical study of the adsorption of dysprosium (Dy3+) in aqueous solution onto two types of activated carbons synthesized from spent coffee ground. KOH activated carbon is a microporous material with a specific BET surface area of 2330 m2·g-1 and pores with a diameter of 3.2 nm. Carbon activated with water vapor and N2 is a solid mesoporous, with pores of 5.7 nm in diameter and a specific surface of 982 m2·g-1. A significant dependence of the adsorption capacity on the solution pH was found, while it does not depend significantly neither on the dysprosium concentration nor on the temperature. A maximum adsorption capacity of 31.26 mg·g-1 and 33.52 mg·g-1 for the chemically and physically activated carbons, respectively, were found. In both cases, the results obtained from adsorption isotherms and kinetic study were better fit to a Langmuir model and a pseudo-second-order kinetics. In addition, thermodynamic results indicate that dysprosium adsorption onto both activated carbons is an exothermic, spontaneous and favorable process.

scholarly journals ADSORPTION OF MALACHITE GREEN DYE USING SPENT COFFEE GROUND BIOCHAR: OPTIMISATION USING RESPONSE SURFACE METHODOLOGY

2020 ◽  
Vol 83 (1) ◽  
pp. 27-36
Author(s):  
Mardawani Mohamad ◽  
Rizki Wannahari ◽  
Rosmawani Mohammad ◽  
Noor Fazliani Shoparwe ◽  
Kwan Wei Lun ◽  
...  
Keyword(s):  
Response Surface Methodology ◽  
Adsorption Capacity ◽  
Response Surface ◽  
Malachite Green ◽  
Contact Time ◽  
Quadratic Model ◽  
Adsorbent Dosage ◽  
Coffee Grounds ◽  
Spent Coffee Ground ◽  
Coffee Ground

Used coffee grounds usually end up as landfill. However, the unique structural properties of its porous surface make coffee grounds can be transformed into biochar and performed as an alternative low cost adsorbent. Malachite green (MG) is a readily water soluble dye which is used extensively in textile and aquaculture industries. The mordant complex structures of MG generate destructive effects to animals and environment. In this study, adsorption of malachite green using spent coffee ground biochar as adsorbent was investigated. The experiments were designed in two methods: classical and optimisation by response surface methodology. Three parameters were studied, which are adsorbent dosage, contact time and pH while the responses in this study are malachite green removal (%) and adsorption capacity (mg/g). Optimisation studies were performed using response surface methodology. Quadratic model was chosen for both response and studied using central composite design. The correlation coefficient, R2 for the quadratic model of malachite green removal (%) and adsorption capacity (mg/g) were 0.95 and 0.99, respectively. The optimum malachite green removal (%) predicted was found at 99.27%, by using 0.12 g of adsorbent dosage, 43.05 minutes of contact time and pH of 9.45 at desirability of 1.0. The optimum adsorption capacity (mg/g) predicted was found at 118.01 mg/g, by using 0.02 g of adsorbent dosage, 60 minutes of contact time and pH of 10.24 at desirability of 0.98. So, it was concluded that the spent coffee ground biochar can be used as an effective adsorbent for malachite green removal from aqueous solution.

New powder material obtained from spent coffee ground and whey protein; Thermal and morphological analysis

2020 ◽  
Vol 240 ◽  
pp. 122171 ◽  
Author(s):  
J. Osorio-Arias ◽  
S. Delgado-Arias ◽  
Y. Duarte-Correa ◽  
E. Largo-Ávila ◽  
D. Montaño ◽  
...  
Keyword(s):  
Whey Protein ◽  
Powder Material ◽  
Morphological Analysis ◽  
Spent Coffee Ground ◽  
Coffee Ground
Sign in / Sign up

Export Citation Format

Share Document