Durability performance of rubberized mortar and concrete with NaOH-Solution treated rubber particles

2017 ◽  
Vol 153 ◽  
pp. 496-505 ◽  
Author(s):  
Ruizhe Si ◽  
Shuaicheng Guo ◽  
Qingli Dai
Keyword(s):  
Solution Treated ◽  
Rubber Particles ◽  
Naoh Solution ◽  
Rubberized Mortar ◽  
Durability Performance

Using of recycled clay brick/fine soil to produce sodium hydroxide alkali activated mortars

2021 ◽  
pp. 136943322110157
Author(s):  
Radhwan Alzeebaree ◽  
Arass Omer Mawlod ◽  
Alaa Mohammedameen ◽  
Anıl Niş
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Clay Brick ◽  
Fine Soil ◽  
Brick Powder ◽  
Naoh Solution ◽  
Water Sorptivity ◽  
Durability Performance ◽  
Alkali Activated

In the study, the recycled clay brick powder/fine soil powder-based sodium hydroxide alkali-activated mortar (AAM) specimens were prepared by mixing different percentages (100/0, 80/20, 60/40, 40/60, 20/80, and 100/0, respectively) to investigate the mechanical and durability performance of sustainable AAM specimens for the possible utilization instead of OPC. The constant ratio of glass powder was used in the production of AAM to increase the alkalinity and improve the mechanical properties of alkali-activated mortar. Also, the influences of sodium hydroxide molarity concentrations (8, 10, 12, 14, and 16 M) on the performance of AAM specimens were studied. The compressive strength, water absorption, and water sorptivity tests were conducted on the AAM specimens and the relationships between the investigated parameters were analyzed. The obtained results revealed that the fine soil powder replacement with clay brick powder improved the compressive strength, and reduced water absorption and water sorptivity up to 80% replacement ratios, and the superior mechanical and durability performance was obtained in the 80% fine soil powder-based AAM specimens. For the higher fine soil powder replacement ratio (100%), the performances of the AAM specimens were found to be adversely affected. Besides, the concentration of NaOH solution significantly influenced the material performances of the fine soil powder-based AAMs and 12 M NaOH concentration performed superior mechanical and durability performance. The strength enhancement of the AAMs was found to be significant after 90 days of ambient curing period.

scholarly journals On the Fresh/Hardened Properties of Cement Composites Incorporating Rubber Particles from Recycled Tires

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Alessandra Fiore ◽  
Giuseppe Carlo Marano ◽  
Cesare Marti ◽  
Marcello Molfetta
Keyword(s):  
Cement Composite ◽  
Cement Composites ◽  
Test Results ◽  
Freezing And Thawing ◽  
Chloride Permeability ◽  
Fine Aggregates ◽  
Rubber Particles ◽  
Suitable Amount ◽  
Hardened Properties ◽  
Rubberized Mortar

This study investigates the ameliorative effects on some properties of cement-based materials which can be obtained by incorporating rubber particles as part of the fine aggregates. The aim is to find out optimal cement composite/mortar mixtures, containing recycled-tyre rubber particles, suitable for specific engineering applications. Different percentages of rubber particles, from 0% to 75%, were used and, for each percentage, the suitable amount of sand was investigated in order to achieve the best fresh/hardened performances. In particular the following characteristics were examined: density, compressive strength, modulus of elasticity, shrinkage, weight loss, flexural behaviour, thermal conductivity, rapid freezing and thawing durability, and chloride permeability. The experimental results were compared with the ones of cement composite specimens without rubber aggregates. Test results show that the proposed rubberized mortar mixes are particularly suitable for some industrial and architectural applications, such as under-rail bearings, road constructions, paving slabs, false facades, and stone backing.

Experimental Study on the Effect of Different Pretreatment Methods on Rubber Concrete Work Performance and Compressive Strength

2014 ◽  
Vol 507 ◽  
pp. 421-424
Author(s):  
Qun Yu ◽  
Kun Zhang
Keyword(s):  
Compressive Strength ◽  
Work Performance ◽  
Rubber Particle ◽  
Concrete Block ◽  
Improve Performance ◽  
Rubber Particles ◽  
Naoh Solution ◽  
Compressive Strength Of Concrete ◽  
Rubber Concrete ◽  
Pretreatment Solution

In untreated, clean water, NaOH solution to clean, CCl4 solution to clean the rubber particles of different pretreatments as the main influencing factors, by 51 rubber concrete block pilot study reached different pretreatment methods on different rubber particle size and dosage of rubber concrete workability and compressive strength were investigated. The results show that: water, NaOH solution, CCl4 pretreatment solution, such as a rubber concrete workability and compressive strength were improved, and the rubber particles larger pretreatment on rubber compressive strength of concrete work to improve performance and more obvious.

The coprecipitation of Cr3P and Cr in Cu

1988 ◽  
Vol 46 ◽  
pp. 764-765
Author(s):  
M.J. Witcomb ◽  
U. Dahmen ◽  
K.H. Westmacott
Keyword(s):  
Orientation Relationship ◽  
Interface Structure ◽  
Model System ◽  
Relative Orientation ◽  
Age Hardening ◽  
Precipitation Behavior ◽  
Solution Treated ◽  
Small Needle ◽  
Diffraction Patterns ◽  
Interface Structures

Cu-Cr age-hardening alloys are of interest as a model system for the investigation of fcc/bcc interface structures. Several past studies have investigated the morphology and interface structure of Cr precipitates in a Cu matrix (1-3) and good success has been achieved in understanding the crystallography and strain contrast of small needle-shaped precipitates. The present study investigates the effect of small amounts of phosphorous on the precipitation behavior of Cu-Cr alloys.The same Cu-0.3% Cr alloy as was used in earlier work was rolled to a thickness of 150 μm, solution treated in vacuum at 1050°C for 1h followed by quenching and annealing for various times at 820 and 863°C.Two laths and their corresponding diffraction patterns in an alloy aged 2h at 820°C are shown in correct relative orientation in Fig. 1. To within the limit of accuracy of the diffraction patterns the orientation relationship was that of Kurdjumov-Sachs (KS), i.e. parallel close-packed planes and directions.

Precipitation in Al + 4% Cu Epitaxial Films

1968 ◽  
Vol 26 ◽  
pp. 384-385
Author(s):  
S. Herd ◽  
S. M. Mader
Keyword(s):  
Solid Solution ◽  
Bulk Material ◽  
Epitaxial Films ◽  
Detectable Change ◽  
Cu Films ◽  
Solution Treated ◽  
Single Crystal Films ◽  
Crystal Films ◽  
Diffraction Patterns ◽  
Deposited Films

Single crystal films in (001) orientation, about 1500 Å thick, were produced by R-F sputtering of Al + 4 wt % Cu onto cleaved KCl at 150°C substrate temperature. The as-deposited films contained numerous θ-CuAl2 particles (C16 structure) about 0.1μ in size. They were transferred onto Mo screens, solution treated and rapidly cooled (within about ½ min) so as to retain a homogeneous solid solution. Subsequently, the films were aged in vacuum at various temperatures in order to induce precipitation and to compare structures and morphologies of precipitate particles in Al-Cu films with those found in age hardened bulk material.Aging for 3 weeks at 60°C or 48 hrs at 100°C did not produce any detectable change in high resolution micrographs or diffraction patterns. In this range Guinier-Preston zones (GP) form in quenched bulk material. The absence of GP in the present experiments in this aging range is perhaps due to the cooling rate employed, which might be more equivalent to an aged and reverted bulk material than to a quenched one.

Observations on the structure at the transformation interface of pearlite in steel

1990 ◽  
Vol 48 (4) ◽  
pp. 200-201
Author(s):  
F. A. Khalid ◽  
D. V. Edmonds
Keyword(s):  
Room Temperature ◽  
Thin Foil ◽  
Carbon Steels ◽  
Model Alloy ◽  
Growth Interface ◽  
Medium Carbon ◽  
Solution Treated ◽  
Medium Carbon Steels ◽  
Alloy Carbide ◽  
Hot Rolled

The austenite/pearlite growth interface in a model alloy steel (Fe-1 lMn-0.8C nominal wt%) is being investigated. In this particular alloy pearlite nodules can be grown isothermally in austenite that remains stable at room temperature, thus facilitating examination of the transformation interfaces. This study presents preliminary results of thin foil TEM of the austenite/pearlite interface, as part of a programme of aimed at studying alloy carbide precipitation reactions at this interface which can result in significant strengthening of microalloyed low- and medium- carbon steels L Similar studies of interface structure, made on a partially decomposed high- Mn austenitic alloy, have been reported recently.The experimental alloys were made as 50 g argon arc melts using high purity materials and homogenised. Samples were hot- rolled, swaged and machined to 3mm diameter rod, solution treated at 1300 °C for 1 hr and WQ. Specimens were then solutionised between 1250 °C and 1000 °C and isothermally transformed between 610 °C and 550 °C for 10-18 hr and WQ.

Precipitation at the transformation interface of pearlite in steel

1990 ◽  
Vol 48 (4) ◽  
pp. 912-913
Author(s):  
F. A. Khalid ◽  
D. V. Edmonds
Keyword(s):  
Thin Foil ◽  
Carbon Steels ◽  
Model Alloy ◽  
Low Carbon ◽  
High Carbon ◽  
Growth Interface ◽  
Medium Carbon ◽  
Interphase Precipitation ◽  
Solution Treated ◽  
Wide Range

The austenite/pearlite growth interface in a model alloy steel (Fe-1lMn-0.8C-0.5V nominal wt%) is being studied in an attempt to characterise the morphology and mechanism of VC precipitation at the growth interface. In this alloy pearlite nodules can be grown isothermally in austenite that remains stable at room temperature thus facilitating examination of the transformation interfaces. This study presents preliminary results of thin foil TEM of the precipitation of VC at the austenite/ferrite interface, which reaction, termed interphase precipitation, occurs in a number of low- carbon HSLA and microalloyed medium- and high- carbon steels. Some observations of interphase precipitation in microalloyed low- and medium- carbon commercial steels are also reported for comparison as this reaction can be responsible for a significant increase in strength in a wide range of commercial steels.The experimental alloy was made as 50 g argon arc melts using high purity materials and homogenised. Samples were solution treated at 1300 °C for 1 hr and WQ. Specimens were then solutionised at 1300 °C for 15 min. and isothermally transformed at 620 °C for 10-18hrs. and WQ. Specimens of microalloyed commercial steels were studied in either as-rolled or as- forged conditions. Detailed procedures of thin foil preparation for TEM are given elsewhere.

Crystallographic Differences of Metastable NI2MO in a NI-MO-AL Superalloy

1980 ◽  
Vol 38 ◽  
pp. 158-159
Author(s):  
Michael M. Kersker ◽  
E. A. Aigeltinger ◽  
J. J. IIren
Keyword(s):  
Mechanical Properties ◽  
Air Cooling ◽  
Solution Treated ◽  
Heat Treated ◽  
Metastable Compounds ◽  
Rapidly Solidified

Ni-rich alloys based on approximate ternary composition Ni-8Mo-15A1 (at%) are presently under investigation in an attempt to study the contribution, if any, of the profusion of Mo-rich NixMo metastable compounds that these alloys contain to their excellent mechanical properties. One of the alloys containing metastable NixMo precipitates is RSR 197 of composition Ni-8.96Mo-15.06A1-1.98Ta-.015Yt. The alloy was prepared at Pratt and Whitney Government Products Division, West Palm Beach, Florida, from rapidly solidified powder. The powder was canned under inert conditions and extruded as rod at 1315°C. The as-extruded rod, after air cooling, was solution treated at 1315°C for two hours, air cooled, and heat treated for one hour at 815°C, followed again by air cooling.

New Technologies for Decontamination of Radioactive Substances Scattered by Nuclear Accident / Nowe Technologie Dekontaminacji Radioaktywnych Substancji Rozproszonych Przez Awarie Nuklearna

2013 ◽  
Vol 58 (1) ◽  
pp. 283-290 ◽  
Author(s):  
Y. Nishizaki ◽  
H. Miyamae ◽  
S. Ichikawa ◽  
K. Izumiya ◽  
T. Takano ◽  
...  
Keyword(s):  
Radioactive Waste ◽  
New Technologies ◽  
Ferric Hydroxide ◽  
Nuclear Accident ◽  
Radioactive Cesium ◽  
Cesium Ions ◽  
Naoh Solution ◽  
High Concentrations ◽  
Water Rinsing

Our effort for decontamination of radioactive cesium scattered widely by nuclear accident in March 2011 in Fukushima, Japan has been described. Radioactive cesium scattered widely in Japan has been accumulating in arc or plasma molten-solidified ash in waste incinerating facilities up to 90,000 Bq/kg of the radioactive waste. Water rinsing of the ash resulted in dissolution of cesium ions together with high concentrations of potassium and sodium ions. Although potassium inhibits the adsorption of cesium on zeolite, we succeeded to precipitate cesium by in-situ formation of ferric ferrocyanide and iron rust in the radioactive filtrate after rinsing of the radioactive ash with water. Because the regulation of no preservation of any kind of cyanide substances, cesium was separated from the precipitate consisting of cesium-captured ferric ferrocyanide and ferric hydroxide in diluted NaOH solution and subsequent filtration gave rise to the potassium-free radioactive filtrate. Cesium was captured by zeolite from the potassium-free radioactive filtrate. The amount of this final radioactive waste of zeolite was significantly lower than that of the arc-molten-solidified ash.

Sign in / Sign up

Export Citation Format

Share Document