Using of recycled clay brick/fine soil to produce sodium hydroxide alkali activated mortars

2021 ◽  
pp. 136943322110157
Author(s):  
Radhwan Alzeebaree ◽  
Arass Omer Mawlod ◽  
Alaa Mohammedameen ◽  
Anıl Niş
Keyword(s):  
Compressive Strength ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Clay Brick ◽  
Fine Soil ◽  
Brick Powder ◽  
Naoh Solution ◽  
Water Sorptivity ◽  
Durability Performance ◽  
Alkali Activated

In the study, the recycled clay brick powder/fine soil powder-based sodium hydroxide alkali-activated mortar (AAM) specimens were prepared by mixing different percentages (100/0, 80/20, 60/40, 40/60, 20/80, and 100/0, respectively) to investigate the mechanical and durability performance of sustainable AAM specimens for the possible utilization instead of OPC. The constant ratio of glass powder was used in the production of AAM to increase the alkalinity and improve the mechanical properties of alkali-activated mortar. Also, the influences of sodium hydroxide molarity concentrations (8, 10, 12, 14, and 16 M) on the performance of AAM specimens were studied. The compressive strength, water absorption, and water sorptivity tests were conducted on the AAM specimens and the relationships between the investigated parameters were analyzed. The obtained results revealed that the fine soil powder replacement with clay brick powder improved the compressive strength, and reduced water absorption and water sorptivity up to 80% replacement ratios, and the superior mechanical and durability performance was obtained in the 80% fine soil powder-based AAM specimens. For the higher fine soil powder replacement ratio (100%), the performances of the AAM specimens were found to be adversely affected. Besides, the concentration of NaOH solution significantly influenced the material performances of the fine soil powder-based AAMs and 12 M NaOH concentration performed superior mechanical and durability performance. The strength enhancement of the AAMs was found to be significant after 90 days of ambient curing period.

The Effect of Activator on the Properties of Low-Calcium Alkali-Activated Mortars

2014 ◽  
Vol 604 ◽  
pp. 169-172 ◽  
Author(s):  
Girts Bumanis ◽  
Diana Bajare ◽  
Janis Locs
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Physical And Mechanical Properties ◽  
Waste Glass ◽  
Structure Investigation ◽  
Structure Development ◽  
Low Calcium ◽  
Naoh Solution ◽  
Alkali Activated

Properties of the low-calcium alkali-activated materials (AAMs) made from the metakaolin, waste glass and sand were tested in this research. Specimens with dimensions 40x40x160mm were prepared. The correlation between development of microstructure and concentration of NaOH solution used for preparing of the AAMs was observed. Structure investigation with SEM and FTIR was performed to describe the formation of microstructure in low-calcium AAMs. The research results aimed that the improvement of physical and mechanical properties of the AAMs with increasing the activator’s concentration from 2 to 10 mol/kg H2O were in concordance with the structure development of AAM. The 28 days old AAMs with a compressive strength up to 31MPa and water absorption lower than 2% were obtained by using activator with concentration 10 mol/kg H2O.

scholarly journals The Effect of Different Types of Internal Curing Liquid on the Properties of Alkali-Activated Slag (AAS) Mortar

2021 ◽  
Vol 13 (4) ◽  
pp. 2407
Author(s):  
Guang-Zhu Zhang ◽  
Xiao-Yong Wang ◽  
Tae-Wan Kim ◽  
Jong-Yeon Lim ◽  
Yi Han
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Deionized Water ◽  
Internal Curing ◽  
Control Group ◽  
Alkali Activated Slag ◽  
Different Types ◽  
Naoh Solution ◽  
Activated Slag ◽  
Alkali Activated

This study shows the effect of different types of internal curing liquid on the properties of alkali-activated slag (AAS) mortar. NaOH solution and deionized water were used as the liquid internal curing agents and zeolite sand was the internal curing agent that replaced the standard sand at 15% and 30%, respectively. Experiments on the mechanical properties, hydration kinetics, autogenous shrinkage (AS), internal temperature, internal relative humidity, surface electrical resistivity, ultrasonic pulse velocity (UPV), and setting time were performed. The conclusions are as follows: (1) the setting times of AAS mortars with internal curing by water were longer than those of internal curing by NaOH solution. (2) NaOH solution more effectively reduces the AS of AAS mortars than water when used as an internal curing liquid. (3) The cumulative heat of the AAS mortar when using water for internal curing is substantially reduced compared to the control group. (4) For the AAS mortars with NaOH solution as an internal curing liquid, compared with the control specimen, the compressive strength results are increased. However, a decrease in compressive strength values occurs when water is used as an internal curing liquid in the AAS mortar. (5) The UPV decreases as the content of zeolite sand that replaces the standard sand increases. (6) When internal curing is carried out with water as the internal curing liquid, the surface resistivity values of the AAS mortar are higher than when the alkali solution is used as the internal curing liquid. To sum up, both NaOH and deionized water are effective as internal curing liquids, but the NaOH solution shows a better performance in terms of reducing shrinkage and improving mechanical properties than deionized water.

scholarly journals Effect of Waste Clay Brick Powder on Physical and Mechanical Properties of Cement Paste

2021 ◽  
Vol 15 (1) ◽  
pp. 370-380
Author(s):  
David Sinkhonde ◽  
Richard Ocharo Onchiri ◽  
Walter Odhiambo Oyawa ◽  
John Nyiro Mwero
Keyword(s):  
Compressive Strength ◽  
Cement Paste ◽  
Setting Time ◽  
Partial Replacement ◽  
Clay Brick ◽  
X Ray ◽  
Cement Replacement ◽  
Clay Bricks ◽  
Brick Powder ◽  
Scanning Electron

Background: Investigations on the use of waste clay brick powder in concrete have been extensively conducted, but the analysis of waste clay brick powder effects on cement paste is limited. Materials and Methods: This paper discusses the effects of waste clay brick powder on cement paste. Fragmented clay bricks were grounded in the laboratory using a ball mill and incorporated into cementitious mixes as partial replacement of Ordinary Portland Cement. Workability, consistency, setting time, density and compressive strength properties of paste mixes were investigated to better understand the impact of waste clay brick powder on the cementitious paste. Four cement replacement levels of 2.5%, 5%, 7.5% and 10% were evaluated in comparison with the control paste. The chemical and mineral compositions were evaluated using X-Ray Fluorescence and X-Ray Diffractometer, respectively. The morphology of cement and waste clay brick powder was examined using a scanning electron microscope. Results: The investigation of workability exhibited a reduction of slump attributed to the significant addition of waste clay brick powder into the cementitious mixes, and it was concluded that waste clay brick powder did not significantly influence the density of the mixes. In comparison with the control paste, increased values of consistency and setting time of cement paste containing waste clay brick powder confirmed the information available in the literature. Conclusion: Although waste clay brick powder decreased the compressive strength of cement paste, 5% partial cement replacement with waste clay brick powder was established as an optimum percentage for specimens containing waste clay brick powder following curing periods of 7 and 28 days. Findings of chemical composition, mineral composition and scanning electron microscopy of waste clay brick powder demonstrated that when finely ground, fragmented clay bricks can be used in concrete as a pozzolanic material.

Mechanical Properties and Thermal Conductivity of Lightweight Clay Bricks Fabricated with a Powdered Marble Dust Additive

2018 ◽  
Vol 777 ◽  
pp. 465-470
Author(s):  
Sutas Janbuala ◽  
Mana Eambua ◽  
Arpapan Satayavibul ◽  
Watcharakhon Nethan
Keyword(s):  
Mechanical Properties ◽  
Thermal Conductivity ◽  
Compressive Strength ◽  
Water Absorption ◽  
Bulk Density ◽  
Firing Temperature ◽  
Apparent Porosity ◽  
Clay Brick ◽  
Clay Bricks ◽  
Marble Dust

The objective of this study was to recycle powdered marble dust to improve mechanical properties and thermal conductivity of lightweight clay bricks. Varying amounts of powdered marble dust (10, 20, 30, and 40 vol.%) were added to a lightweight clay brick at the firing temperatures of 900, 1000, and 1100 °C. When higher quantities of powdered marble dust were added, the values of porosity and water absorption increased while those of thermal conductivity and bulk density decreased. The decrease in apparent porosity and water absorption were also affected by the increase in firing temperature. The most desirable properties of the clay bricks were obtained for the powdered marble dust content of 40 vol.% and firing temperature 900 °C: bulk density of 1.20 g/cm3, compressive strength 9.2 MPa, thermal conductivity 0.32 W/m.K, and water absorption 22.5%.

The Effect of Steel Slag Coarse Aggregate on the Mechanical and Durability Performances of Concrete

2020 ◽  
Vol 833 ◽  
pp. 228-232
Author(s):  
Md. Jihad Miah ◽  
Mohammad Shamim Miah ◽  
Anisa Sultana ◽  
Taukir Ahmed Shamim ◽  
Md Ashraful Alom
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Water Absorption ◽  
Coarse Aggregate ◽  
Steel Slag ◽  
Experimental Investigations ◽  
Clay Brick ◽  
Crushing Strength ◽  
Burnt Clay ◽  
Good Agreement

This work performs experimental investigations on concrete made with difference replacement percentage of first-class burnt clay brick aggregate (0, 10, 20, 30, 40, 50, 60, 80, and 100%) by steel slag (SS) aggregate. The aim is to evaluate the mechanical properties as well as durability performances, additionally, water absorption porosity test is performed to investigate the influence of steel slag aggregate on the durability of tested concrete. The experimental results have shown that the compressive strength was improved significantly due to the replacement of brick aggregate by steel slag aggregate. The crushing strength of concrete made with 100% steel slag aggregate has gained up to 70% more than the control concrete (100% brick aggregate). However, the porosity of concrete was reduced with the adding percentage of brick aggregate by steel slag aggregate which is consistent with the compressive strength results. Further, a quite good agreement between compressive strength and porosity was observed as well.

Study of Manufacture Process and Properties of Tailings and Slag Based Geopolymers

2010 ◽  
Vol 156-157 ◽  
pp. 803-807
Author(s):  
Fu Sheng Niu ◽  
Shan Shan Zhou ◽  
Shu Xian Liu ◽  
Jin Xia Zhang
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Raw Material ◽  
Silicate Concentration ◽  
High Compressive Strength ◽  
Curing Period ◽  
Manufacture Process ◽  
Alkali Activated

The tailings and slag based geopolymers was prepared by sodium silicate, sodium hydroxide alkali-activated tailings and slag. The compressive strength in 7 d under different raw material proportion were tested. The result indicated that tailings and slag based geopolymers has high compressive strength . As the tailings in slag is 80%, the compressive strength in 7d can reach 45.10 MPa . As the Na2SiO3 to NaOH ratio is 0.5, the compressive strength in 7d can reach 63.79 MPa. As the NaOH and sodium silicate concentration in the solution is 35%, the compressive strength in 7d can reach 38.35 MPa respectively; As the curing period is 14 d , the compressive strength can reach 71.25 MPa. As the steel scoria in solid is 20%, the compressive strength in 7d can reach 61.86 MPa respectively.

The Effect of Curing Time on the Properties of Fly Ash-Based Geopolymer Bricks

2012 ◽  
Vol 626 ◽  
pp. 937-941 ◽  
Author(s):  
W.I. Wan Mastura ◽  
H. Kamarudin ◽  
I. Khairul Nizar ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Mohammed
Keyword(s):  
Compressive Strength ◽  
Fly Ash ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Sodium Silicate ◽  
Experimental Work ◽  
Base Material ◽  
Curing Time ◽  
Curing Conditions ◽  
Alkaline Activator

This paper reports the results of an experimental work conducted to investigate the effect of curing conditions on the properties of fly ash-based geopolymer bricks prepared by using fly ash as base material and combination of sodium hydroxide and sodium silicate as alkaline activator. The experiments were conducted by varying the curing time in the range of 1-24 hours respectively. The specimens cured for a period of 24 hours have presented the highest compressive strength for all ratio of fly ash to sand. For increasing curing time improve compressive strength and decreasing water absorption.

scholarly journals Alkali Activated Paste and Concrete Based on of Biomass Bottom Ash with Phosphogypsum

2020 ◽  
Vol 10 (15) ◽  
pp. 5190
Author(s):  
Danutė Vaičiukynienė ◽  
Dalia Nizevičienė ◽  
Aras Kantautas ◽  
Vytautas Bocullo ◽  
Andrius Kielė
Keyword(s):  
Compressive Strength ◽  
Sodium Hydroxide ◽  
Sodium Hydroxide Solution ◽  
Bottom Ash ◽  
Control Sample ◽  
Test Methods ◽  
X Ray ◽  
Hydroxide Solution ◽  
Fine Grained ◽  
Alkali Activated

There is a growing interest in the development of new cementitious binders for building construction activities. In this study, biomass bottom ash (BBA) was used as aluminosilicate precursor and phosphogypsum (PG) was used as a calcium source. The mixtures of BBA and PG were activated with the sodium hydroxide solution or the mixture of sodium hydroxide solution and sodium silicate hydrate solution. Alkali activated binders were investigated using X-ray powder diffraction (XRD), X-ray fluorescence (XRF) and scanning electron microscopy (SEM) test methods. The compressive strength of hardened paste and fine-grained concrete was also evaluated. After 28 days, the highest compressive strength reached 30.0 MPa—when the BBA was substituted with 15% PG and activated with NaOH solution—which is 14 MPa more than control sample. In addition, BBA fine-grained concrete samples based on BBA with 15% PG substitute activated with NaOH/Na2SiO3 solution showed higher compressive strength compered to when NaOH activator was used −15.4 MPa and 12.9 MPa respectfully. The NaOH/Na2SiO3 activator solution resulted reduced open porosity, so potentially the fine-grained concrete resistance to freeze and thaw increased.

The Study on Physical and Thermal Properties of Geopolymer Pastes

2017 ◽  
Vol 751 ◽  
pp. 538-543 ◽  
Author(s):  
Pongsak Jittabut
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Thermal Properties ◽  
Water Absorption ◽  
Sodium Hydroxide ◽  
Bulk Density ◽  
Rice Husk ◽  
Rice Husk Ash ◽  
Weight Ratio ◽  
Thermal Capacity

This research was aimed to a present the physical and thermal properties of geopolymer pastes made of fly ash (FA) and bagasse ash (BA) with rice husk ash (RHA) containing at the doses of 0%, 2%, 4%, 6%, 8% and 10% by weight. The sodium hydroxide concentration of 15 molars, sodium silicate per sodium hydroxide by weight ratio of 2.0, the alkaline liquid per binder at the ratio of 0.60 and curing at ambient temperature were used at the to mix all mixtures to gether for 7 and 28 days. The properties analysis of the geopolymer pastes such as compressive strength, bulk density, water absorption, thermal conductivity, thermal diffusivity and thermal capacity were tested. The results were indicated that geopolymer pastes that containing rice husk ash 2% by weight for 28 days of curing gave the maximum compressive strength of 84.42 kg/cm2, low water absorption of 1.16 %, low bulk density of 2,065.71 kg/cm3, lower thermal conductivity of 1.1173 W/m.K, lower thermal diffusion of 6.643 µm2/s and lower thermal capacity of 1.6819 MJ/m3K, respectively. The utilization of waste from agriculture industry via geopolymer pastes for green building materials can be achieved. For this research, physical properties and thermal insulation of geopolymer pastes were siqnificantly improved.

Sign in / Sign up

Export Citation Format

Share Document