Investigations on fatigue properties of red sandstone under positive and negative pure bending loads

2022 ◽  
Vol 321 ◽  
pp. 126379
Author(s):  
Zhi Wang ◽  
Wenjing Qin ◽  
Yingnan Gao ◽  
Yuxiang Yang ◽  
Haopeng Lv ◽  
...  
1980 ◽  
Vol 102 (1) ◽  
pp. 25-31 ◽  
Author(s):  
R. J. Warner ◽  
V. Pavelic ◽  
R. G. Taschner

This paper presents S-N data generated on a newly designed tuning fork system. The materials tested were four different specimen groups of ductile iron. The tuning fork was designed to continuously monitor reversed bending loads applied to the specimen. The main objective of the project was to develop S-N curves for four particular groups of ductile iron materials. The basic material was an SAE-D5506 ductile iron, tested in both an as-cast condition and with a machined surface finish. This same material was tested in a quenched and tempered state, (SAE-DQ&T, MS-612 Grade, 1000S) with both as-cast and machined finishes. In order to carry out these experiments a test apparatus had to be designed, assembled, and calibrated. The end result of this procedure was a versatile tuning fork fixture for the application of the required pure bending loads and a permenent monitoring system calibrated to the loads applied to the specimen. This monitoring system, once calibrated, eliminated the need to strain gage each of the many specimens to be tested. The paper concludes with discussion of the results obtained. The material S-N data presented includes comparative points for the four log-log lines as computed by linear regression techniques.


2000 ◽  
Vol 203 (18) ◽  
pp. 2737-2745 ◽  
Author(s):  
M.L. Knothe Tate ◽  
R. Steck ◽  
M.R. Forwood ◽  
P. Niederer

Load-induced extravascular fluid flow has been postulated to play a role in mechanotransduction of physiological loads at the cellular level. Furthermore, the displaced fluid serves as a carrier for metabolites, nutrients, mineral precursors and osteotropic agents important for cellular activity. We hypothesise that load-induced fluid flow enhances the transport of these key substances, thus helping to regulate cellular activity associated with processes of functional adaptation and remodelling. To test this hypothesis, molecular tracer methods developed previously by our group were applied in vivo to observe and quantify the effects of load-induced fluid flow under four-point-bending loads. Preterminal tracer transport studies were carried out on 24 skeletally mature Sprague Dawley rats. Mechanical loading enhanced the transport of both small- and larger-molecular-mass tracers within the bony tissue of the tibial mid-diaphysis. Mechanical loading showed a highly significant effect on the number of periosteocytic spaces exhibiting tracer within the cross section of each bone. For all loading rates studied, the concentration of Procion Red tracer was consistently higher in the tibia subjected to pure bending loads than in the unloaded, contralateral tibia. Furthermore, the enhancement of transport was highly site-specific. In bones subjected to pure bending loads, a greater number of periosteocytic spaces exhibited the presence of tracer in the tension band of the cross section than in the compression band; this may reflect the higher strains induced in the tension band compared with the compression band within the mid-diaphysis of the rat tibia. Regardless of loading mode, the mean difference between the loaded side and the unloaded contralateral control side decreased with increasing loading frequency. Whether this reflects the length of exposure to the tracer or specific frequency effects cannot be determined by this set of experiments. These in vivo experimental results corroborate those of previous ex vivo and in vitro studies. Strain-related differences in tracer distribution provide support for the hypothesis that load-induced fluid flow plays a regulatory role in processes associated with functional adaptation.


1981 ◽  
Vol 16 (4) ◽  
pp. 251-259 ◽  
Author(s):  
H R Evans ◽  
N E Shanmugam

An experimental study of the ultimate load behaviour of small-scale steel box girder models is described. The models were subjected either to predominant shear or pure bending loads and, in the latter case, openings were introduced into the webs of two of the models. The effects of these openings are shown to be small. Simple theories are applied and are shown to give reasonably accurate predictions of the failure loads.


2013 ◽  
Vol 51 (5) ◽  
pp. 325-332 ◽  
Author(s):  
Sung Hyuk Park ◽  
Seong-Gu Hong ◽  
Chong Soo Lee ◽  
Ha Sik Kim

1986 ◽  
Vol 14 (1) ◽  
pp. 3-32 ◽  
Author(s):  
P. Popper ◽  
C. Miller ◽  
D. L. Filkin ◽  
W. J. Schaffers

Abstract A mathematical analysis of radial tire cornering was performed to predict tire deflections and belt-edge separation strains. The model includes the effects of pure bending, transverse shear bending, lateral restraint of the carcass on the belt, and shear displacements between belt and carcass. It also provides a description of the key mechanisms that act during cornering. The inputs include belt and carcass cord properties, cord angle, pressure, rubber properties, and cornering force. Outputs include cornering deflections and interlaminar shear strains. Key relations found between tire parameters and responses were the optimum angle for minimum cornering deflections and its dependence on cord modulus, and the effect of cord angle and modulus on interlaminar shear strains.


A study review of aging polymer composite materials (PCM) under different heat-moisture conditions or water exposure with the sequential or parallel influence of static or cyclic loads in laboratory conditions is presented. The influence of tension and bending loads is compared. Conditions of the different load influence on parameters of carbon-reinforced plastics and glass-reinforced plastics are discussed. Equipment and units for climatic tests of PCM under loading are described. Simulation examples of indices of mechanical properties of PCM under the influence of environment and loads are shown.


Sign in / Sign up

Export Citation Format

Share Document