Experimental and computational study on the effects of injection timing on thermodynamics, combustion and emission characteristics of a natural gas (NG)-diesel dual fuel engine at low speed and low load

2018 ◽  
Vol 160 ◽  
pp. 426-438 ◽  
Author(s):  
Jun Shu ◽  
Jianqin Fu ◽  
Jingping Liu ◽  
Lei Zhang ◽  
Zhichao Zhao
Keyword(s):  
Natural Gas ◽  
Computational Study ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Low Speed ◽  
Low Load

scholarly journals A Numerical Study on the Combustion Process and Emission Characteristics of a Natural Gas-Diesel Dual-Fuel Marine Engine at Full Load

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1342
Author(s):  
Van Chien Pham ◽  
Jae-Hyuk Choi ◽  
Beom-Seok Rho ◽  
Jun-Soo Kim ◽  
Kyunam Park ◽  
...  
Keyword(s):  
Natural Gas ◽  
Combustion Process ◽  
Simulation Software ◽  
Dual Fuel ◽  
Injection Timing ◽  
Emission Characteristics ◽  
Cylinder Pressure ◽  
Marine Engine ◽  
Full Load ◽  
Simulation Results

This paper presents research on the combustion and emission characteristics of a four-stroke Natural gas–Diesel dual-fuel marine engine at full load. The AVL FIRE R2018a (AVL List GmbH, Graz, Austria) simulation software was used to conduct three-dimensional simulations of the combustion process and emission formations inside the engine cylinder in both diesel and dual-fuel mode to analyze the in-cylinder pressure, temperature, and emission characteristics. The simulation results were then compared and showed a good agreement with the measured values reported in the engine’s shop test technical data. The simulation results showed reductions in the in-cylinder pressure and temperature peaks by 1.7% and 6.75%, while NO, soot, CO, and CO2 emissions were reduced up to 96%, 96%, 86%, and 15.9%, respectively, in the dual-fuel mode in comparison with the diesel mode. The results also show better and more uniform combustion at the late stage of the combustions inside the cylinder when operating the engine in the dual-fuel mode. Analyzing the emission characteristics and the engine performance when the injection timing varies shows that, operating the engine in the dual-fuel mode with an injection timing of 12 crank angle degrees before the top dead center is the best solution to reduce emissions while keeping the optimal engine power.

A phenomenological combustion analysis of a dual-fuel natural-gas diesel engine

2016 ◽  
Vol 231 (1) ◽  
pp. 66-83 ◽  
Author(s):  
Shuonan Xu ◽  
David Anderson ◽  
Mark Hoffman ◽  
Robert Prucka ◽  
Zoran Filipi
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Heat Release ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Dual Fuel ◽  
Injection Timing ◽  
Heavy Duty ◽  
Engine System ◽  
Wiebe Function

Energy security concerns and an abundant supply of natural gas in the USA provide the impetus for engine designers to consider alternative gaseous fuels in the existing engines. The dual-fuel natural-gas diesel engine concept is attractive because of the minimal design changes, the ability to preserve a high compression ratio of the baseline diesel, and the lack of range anxiety. However, the increased complexity of a dual-fuel engine poses challenges, including the knock limit at a high load, the combustion instability at a low load, and the transient response of an engine with directly injected diesel fuel and port fuel injection of compressed natural gas upstream of the intake manifold. Predictive simulations of the complete engine system are an invaluable tool for investigations of these conditions and development of dual-fuel control strategies. This paper presents the development of a phenomenological combustion model of a heavy-duty dual-fuel engine, aided by insights from experimental data. Heat release analysis is carried out first, using the cylinder pressure data acquired with both diesel-only and dual-fuel (diesel and natural gas) combustion over a wide operating range. A diesel injection timing correlation based on the injector solenoid valve pulse widths is developed, enabling the diesel fuel start of injection to be detected without extra sensors on the fuel injection cam. The experimental heat release trends are obtained with a hybrid triple-Wiebe function for both diesel-only operation and dual-fuel operation. The ignition delay period of dual-fuel operation is examined and estimated with a predictive correlation using the concept of a pseudo-diesel equivalence ratio. A four-stage combustion mechanism is discussed, and it is shown that a triple-Wiebe function has the ability to represent all stages of dual-fuel combustion. This creates a critical building block for modeling a heavy-duty dual-fuel turbocharged engine system.

Simulation Research on Combustion Process in a Natural Gas-Diesel Dual-Fuel Marine Engine

2014 ◽  
Vol 525 ◽  
pp. 227-231 ◽  
Author(s):  
Min Xiao ◽  
Chun Long Feng
Keyword(s):  
Natural Gas ◽  
Total Energy ◽  
Combustion Process ◽  
Power Reduction ◽  
Dual Fuel ◽  
Injection Timing ◽  
Simulation Research ◽  
Injection Duration ◽  
Medium Speed ◽  
The Right

In order to solve the problem of Diesel natural gas dual fuel engine, such as power reduction, low charging efficiency, the conception of diesel engine fueled with pilot-ignited directly-injected liquefied natural gas is put forward. On the basis of this theory, a medium speed diesel of the marine is refitted into dual fuel engine, in order to keep original power, decrease the temperature of combustion and reduce emission. The LNG injection timing, duration of LNG injection and the different ratios the pilot diesel to total energy are studied the method of AVL FIRE software. Conclusions are as follows: When the different ratios pilot diesel to total energy is 0.5%, the engine can not work; Delaying the LNG injection timing, shortening the LNG injection duration and choose the right ratios pilot diesel to total energy can reach the indicated power of original machine, and the NOx emissions level will be greatly reduced.

Performance of Dual Fuel Engine Running on Jojoba Oil as Pilot Fuel and CNG or LPG

2007 ◽  
Author(s):  
Mohamed Y. E. Selim ◽  
M. S. Radwan ◽  
H. E. Saleh
Keyword(s):  
Methyl Ester ◽  
Natural Gas ◽  
Pressure Rise ◽  
Combustion Noise ◽  
Dual Fuel ◽  
Maximum Pressure ◽  
Injection Timing ◽  
Pressure Rise Rate ◽  
Rise Rate ◽  
Pilot Fuel

The use of Jojoba Methyl Ester as a pilot fuel was investigated for almost the first time as a way to improve the performance of dual fuel engine running on natural gas or LPG at part load. The dual fuel engine used was Ricardo E6 variable compression diesel engine and it used either compressed natural gas (CNG) or liquefied petroleum gas (LPG) as the main fuel and Jojoba Methyl Ester as a pilot fuel. Diesel fuel was used as a reference fuel for the dual fuel engine results. During the experimental tests, the following have been measured: engine efficiency in terms of specific fuel consumption, brake power output, combustion noise in terms of maximum pressure rise rate and maximum pressure, exhaust emissions in terms of carbon monoxide and hydrocarbons, knocking limits in terms of maximum torque at onset of knocking, and cyclic data of 100 engine cycle in terms of maximum pressure and its pressure rise rate. The tests examined the following engine parameters: gaseous fuel type, engine speed and load, pilot fuel injection timing, pilot fuel mass and compression ratio. Results showed that using the Jojoba fuel with its improved properties has improved the dual fuel engine performance, reduced the combustion noise, extended knocking limits and reduced the cyclic variability of the combustion.

Emission Characteristics from Diesel Engine with Emulsion Fuel and Natural Gas Dual Fuel

2021 ◽  
Vol 25 (5) ◽  
pp. 22-28
Author(s):  
Suk-Ho Jung ◽  
Ji-Ho Kim ◽  
Sang-Won Kim ◽  
Jeong-Min Cheon
Keyword(s):  
Diesel Engine ◽  
Natural Gas ◽  
Dual Fuel ◽  
Emission Characteristics
Sign in / Sign up

Export Citation Format

Share Document