Research of large scale mechanical structure crack growth method based on finite element parametric submodel

2019 ◽  
Vol 102 ◽  
pp. 226-236 ◽  
Author(s):  
Yuantao Sun ◽  
Jinjin Zhai ◽  
Qing Zhang ◽  
Xianrong Qin
Keyword(s):  
Finite Element ◽  
Crack Growth ◽  
Large Scale ◽  
Mechanical Structure ◽  
Growth Method ◽  
Structure Crack

Validation of Crack Growth for an Finite Element Based ECA Procedure for Reel-Laid Pipelines With Under-Matching Girth Welds

2015 ◽  
Author(s):  
T. Sriskandarajah ◽  
Daowu Zhou ◽  
Lingjun Cao
Keyword(s):  
Finite Element ◽  
Crack Growth ◽  
Large Scale ◽  
Limit Load ◽  
Bending Test ◽  
Offshore Pipelines ◽  
Reference Stress ◽  
Trial Test ◽  
3D Fea ◽  
Girth Welds

There is a concern on the fracture integrity of the partially over-matching or under-matching weld during reel-lay installation where there is large plastic strain in the pipe. Conventional ECA procedures such as BS7910 and DNV-OS-F101 are applicable for fully over-matching welds only, due to limitations in the reference stress solution (or limit load solutions). The ECA procedure based on 3D finite element (FE) analysis was developed for partially over-matching welds or under-matching. The methodology has been successfully applied to several projects of industry-wide significance, with partially over-matching welds in offshore pipelines. This paper provides a case study validating the crack growth from FE based ECA methodology against the large scale bending trial test where the pipe containing the notched defect was pre-strained under a series of straining cycles. A comparison of the crack growth between 3D FEA and the large scale bending test was presented.

ORNL Pre-Test Analyses of a Large-Scale Experiment in STYLE

2011 ◽  
Author(s):  
Paul T. Williams ◽  
Shengjun Yin ◽  
Hilda B. Klasky ◽  
B. Richard Bass
Keyword(s):  
Finite Element ◽  
Fracture Mechanics ◽  
Crack Growth ◽  
Probabilistic Analysis ◽  
Alternative Assessment ◽  
Large Scale ◽  
Structural Integrity ◽  
Nuclear Industry ◽  
Work Package ◽  
Scale Experiment

Oak Ridge National Laboratory (ORNL) is conducting a series of numerical analyses to simulate a large scale mock-up experiment planned within the European Network for Structural Integrity for Lifetime Management – non-RPV Components (STYLE). STYLE is a European cooperative effort to assess the structural integrity of (non-reactor pressure vessel) reactor coolant pressure boundary components relevant to ageing and life-time management and to integrate the knowledge created in the project into mainstream nuclear industry assessment codes. ORNL contributes “work-in-kind” support to STYLE Work Package 2 (Numerical Analysis/Advanced Tools) and Work Package 3 (Engineering Assessment Methods/LBB Analyses). This paper summarizes the current status of ORNL analyses of the STYLE Mock-Up3 large-scale experiment to simulate and evaluate crack growth in a cladded ferritic pipe. The analyses are being performed in two parts. In the first part, advanced fracture mechanics models are being developed and performed to evaluate several experiment designs taking into account the capabilities of the test facility while satisfying the test objectives. Then these advanced fracture mechanics models will be utilized to simulate the crack growth in the large scale mock-up test. For the second part, the recently developed ORNL SIAM-PFM open-source, cross-platform, probabilistic computational tool will be used to generate an alternative assessment for comparison with the advanced fracture mechanics model results. The SIAM-PFM probabilistic analysis of the Mock-Up3 experiment will utilize fracture modules that are installed into a general probabilistic framework. The probabilistic results of the Mock-Up3 experiment obtained from SIAM-PFM will be compared to those results generated using the deterministic 3D nonlinear finite-element modeling approach. The objective of the probabilistic analysis is to provide uncertainty bounds that will assist in assessing the more detailed 3D finite-element solutions and to also assess the level of confidence that can be placed in the best-estimate finite-element solutions.

Analysis of Ductile Crack Growth in Pipe Test in STYLE Project

2012 ◽  
Author(s):  
Shengjun Yin ◽  
Paul T. Williams ◽  
Hilda B. Klasky ◽  
B. Richard Bass
Keyword(s):  
Finite Element ◽  
Crack Growth ◽  
Large Scale ◽  
Structural Integrity ◽  
Bending Test ◽  
Ductile Crack ◽  
Oak Ridge ◽  
Integrity Assessment ◽  
Ductile Crack Growth ◽  
Bending Load

The Oak Ridge National Laboratory (ORNL) is conducting structural analyses, both deterministic and probabilistic, to simulate a large scale mock-up experiment planned within the European Network for Structural Integrity for Lifetime Management – non-RPV Components (STYLE). The paper summarizes current ORNL analyses of STYLE’s Mock-Up3 experiment to simulate/evaluate ductile crack growth in a cladded ferritic pipe. Deterministic analyses of the large-scale bending test of a ferritic surge pipe, with an internal circumferential crack, are being simulated with a number of local micromechanical approaches, such as Gurson-Tvergaard-Needleman (GTN) model. Both FEACrack [1] and ABAQUS [2] general purpose finite element programs are being used to predict the failure load and the failure mode, i.e. ductile tearing or net-section collapse, as part of the pre-test phase of the project. Companion probabilistic analyses of the experiment are utilizing the ORNL developed open-source Structural Integrity Assessment Modular - Probabilistic Fracture Mechanics (SIAM-PFM) framework. SIAM-PFM contains engineering assessment methodologies such as the tearing instability (J-T analysis) module developed for inner surface cracks under bending load. The driving force J-integral estimations are based on the SC.ENG1 or SC.ENG2 models. The J-A2 methodology is used to transfer (constraint-adjust) J-R curve material data from standard test specimens to the Mock-Up3 experiment configuration. The probabilistic results of the Mock-Up3 experiment obtained from SIAM-PFM will be compared to those generated using the deterministic finite element modeling approach. The objective of the probabilistic analysis is to provide uncertainty bounds that will assist in assessing the more detailed 3D finite-element solutions and to also assess the level of confidence that can be placed in the best-estimate finite-element solutions.

scholarly journals Fatigue Crack Growth Analysis with Extended Finite Element for 3D Linear Elastic Material

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 397
Author(s):  
Yahya Ali Fageehi
Keyword(s):  
Finite Element ◽  
Fatigue Crack ◽  
Fatigue Life ◽  
Crack Propagation ◽  
Crack Growth ◽  
Mixed Mode ◽  
Propagation Path ◽  
Loading Conditions ◽  
Extended Finite Element ◽  
Linear Elastic

This paper presents computational modeling of a crack growth path under mixed-mode loadings in linear elastic materials and investigates the influence of a hole on both fatigue crack propagation and fatigue life when subjected to constant amplitude loading conditions. Though the crack propagation is inevitable, the simulation specified the crack propagation path such that the critical structure domain was not exceeded. ANSYS Mechanical APDL 19.2 was introduced with the aid of a new feature in ANSYS: Smart Crack growth technology. It predicts the propagation direction and subsequent fatigue life for structural components using the extended finite element method (XFEM). The Paris law model was used to evaluate the mixed-mode fatigue life for both a modified four-point bending beam and a cracked plate with three holes under the linear elastic fracture mechanics (LEFM) assumption. Precise estimates of the stress intensity factors (SIFs), the trajectory of crack growth, and the fatigue life by an incremental crack propagation analysis were recorded. The findings of this analysis are confirmed in published works in terms of crack propagation trajectories under mixed-mode loading conditions.

scholarly journals Stator Non-Uniform Radial Ventilation Design Methodology for a 15 MW Turbo-Synchronous Generator Based on Single Ventilation Duct Subsystem

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2760
Author(s):  
Ruiye Li ◽  
Peng Cheng ◽  
Hai Lan ◽  
Weili Li ◽  
David Gerada ◽  
...  
Keyword(s):  
Finite Element ◽  
Temperature Distribution ◽  
Design Methodology ◽  
Large Scale ◽  
Synchronous Generator ◽  
Axial Direction ◽  
Scale Model ◽  
Element Analysis ◽  
Axial Temperature ◽  
Ventilation Duct

Within large turboalternators, the excessive local temperatures and spatially distributed temperature differences can accelerate the deterioration of electrical insulation as well as lead to deformation of components, which may cause major machine malfunctions. In order to homogenise the stator axial temperature distribution whilst reducing the maximum stator temperature, this paper presents a novel non-uniform radial ventilation ducts design methodology. To reduce the huge computational costs resulting from the large-scale model, the stator is decomposed into several single ventilation duct subsystems (SVDSs) along the axial direction, with each SVDS connected in series with the medium of the air gap flow rate. The calculation of electromagnetic and thermal performances within SVDS are completed by finite element method (FEM) and computational fluid dynamics (CFD), respectively. To improve the optimization efficiency, the radial basis function neural network (RBFNN) model is employed to approximate the finite element analysis, while the novel isometric sampling method (ISM) is designed to trade off the cost and accuracy of the process. It is found that the proposed methodology can provide optimal design schemes of SVDS with uniform axial temperature distribution, and the needed computation cost is markedly reduced. Finally, results based on a 15 MW turboalternator show that the peak temperature can be reduced by 7.3 ∘C (6.4%). The proposed methodology can be applied for the design and optimisation of electromagnetic-thermal coupling of other electrical machines with long axial dimensions.

scholarly journals Advantageous Description of Short Fatigue Crack Growth Rates in Austenitic Stainless Steels with Distinct Properties

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 475
Author(s):  
Lukáš Trávníček ◽  
Ivo Kuběna ◽  
Veronika Mazánová ◽  
Tomáš Vojtek ◽  
Jaroslav Polák ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Stainless Steels ◽  
Growth Rates ◽  
Large Scale ◽  
J Integral ◽  
Scale Yielding ◽  
Residual Fatigue ◽  
Crack Growth Rates

In this work two approaches to the description of short fatigue crack growth rate under large-scale yielding condition were comprehensively tested: (i) plastic component of the J-integral and (ii) Polák model of crack propagation. The ability to predict residual fatigue life of bodies with short initial cracks was studied for stainless steels Sanicro 25 and 304L. Despite their coarse microstructure and very different cyclic stress–strain response, the employed continuum mechanics models were found to give satisfactory results. Finite element modeling was used to determine the J-integrals and to simulate the evolution of crack front shapes, which corresponded to the real cracks observed on the fracture surfaces of the specimens. Residual fatigue lives estimated by these models were in good agreement with the number of cycles to failure of individual test specimens strained at various total strain amplitudes. Moreover, the crack growth rates of both investigated materials fell onto the same curve that was previously obtained for other steels with different properties. Such a “master curve” was achieved using the plastic part of J-integral and it has the potential of being an advantageous tool to model the fatigue crack propagation under large-scale yielding regime without a need of any additional experimental data.

Sign in / Sign up

Export Citation Format

Share Document